Grizzly T33304 Bedienungsanleitung

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#JM22320 PRINTED IN CHINA

MODEL T33304

3-in-1 20V COMPACT ROUTER

OWNER'S MANUAL

(For models manufactured since 05/22)

V1.09.22

***Keep for Future Reference***

Model T33304 shown

w/optional battery.

This manual provides critical safety instructions on the proper setup,

operation, maintenance, and service of this machine/tool. Save this

document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual

may result in fire or serious personal injury—including amputation,

electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in

a safe environment, personnel training and usage authorization,

proper inspection and maintenance, manual availability and compre-

hension, application of safety devices, cutting/sanding/grinding tool

integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage

from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

Model T33304 (Mfd. Since 05/22) -1-

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazard-

ous conditions. This manual uses a series of symbols and signal words which

are intended to convey the level of importance of the safety messages. The

progression of symbols is described below. Remember that safety messages by

themselves do not eliminate danger and are not a substitute for proper accident

prevention measures.

Indicates an imminent hazardous situation which, if

not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, MAY result in minor or moderate injury.

It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful infor-

mation about proper operation of the equipment.

NOTICE

Safety Instructions for Power Tools

OWNER’S MANUAL. Read and under-

stand this owner’s manual BEFORE using

machine.

TRAINED OPERATORS ONLY. Untrained

operators have a higher risk of being hurt

or killed. Only allow trained/supervised

people to use this power tool. When tool

is not being used, disconnect power, and

store in out-of-reach location to prevent

unauthorized use—especially around

children. Make workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not

use tools in areas that are wet, cluttered,

or have poor lighting. Operating tools in

these areas greatly increases risk of acci-

dents and injury.

MENTAL ALERTNESS REQUIRED. Full

mental alertness is required for safe oper-

ation of power tools. Never operate under

the influence of drugs or alcohol, when

tired, or when distracted.

DISCONNECT POWER FIRST. Always

disconnect tool from power supply

BEFORE making adjustments, changing

tooling, or servicing machine. This pre-

vents an injury risk from unintended startup

or contact with live electrical components.

EYE PROTECTION. Always wear ANSI-

approved safety glasses or a face shield

when operating or observing machinery to

reduce the risk of eye injury or blindness

from flying particles. Everyday eyeglasses

are not approved safety glasses.

Model T33304 (Mfd. Since 05/22)-2-

ELECTRICAL SAFETY. Tool plug must

match outlet. Double-insulated tools have

a polarized plug (one blade is wider than

the other), which must be plugged into a

polarized outlet. Never modify plug. Do

not use adapter for grounded tools. Use

a ground fault circuit interrupter if opera-

tion is unavoidable in damp locations.

Avoid touching grounded surfaces when

operating tool.

WEARING PROPER APPAREL. Do not

wear clothing, apparel or jewelry that

can become entangled in moving parts.

Always tie back or cover long hair. Wear

non-slip footwear to avoid accidental

slips, which could cause loss of workpiece

control. Wear hard hat as needed.

HAZARDOUS DUST. Dust created while

using tools may cause cancer, birth

defects, or long-term respiratory damage.

Be aware of dust hazards associated with

each workpiece material, always wear

a NIOSH-approved respirator, and con-

nect tool to an appropriate dust collection

device to reduce your risk.

HEARING PROTECTION. Always wear

hearing protection when operating or

observing loud machinery. Extended

exposure to this noise without hearing

protection can cause permanent hearing

loss.

REMOVE ADJUSTING TOOLS. Never

leave adjustment tools, chuck keys,

wrenches, etc. in or on tool—especially

near moving parts. Verify removal before

starting!

INTENDED USAGE. Only use tool for its

intended purpose. Never modify or alter

tool for a purpose not intended by the

manufacturer or serious injury or death

may result!

AWKWARD POSITIONS. Keep proper

footing and balance at all times when

operating tool. Do not overreach! Avoid

awkward hand positions that make tool

control difficult or increase the risk of

accidental injury.

SAFE HANDLING. Firmly grip tool. To

avoid accidental firing, do not keep finger

on switch or trigger while carrying.

FORCING TOOLS.. Use right tool for job,

and do not force it. It will do job safer and

better at rate for which it was designed.

SECURING WORKPIECE. When

required, use clamps or vises to secure

workpiece. This protects hands and frees

both of them to operate tool.

GUARDS & COVERS. Guards and cov-

ers reduce accidental contact with mov-

ing parts or flying debris. Ensure they

are properly installed, undamaged, and

working correctly.

CHILDREN & BYSTANDERS. Keep chil-

dren and bystanders at a safe distance

from the work area. Stop using tool if they

become a distraction.

USE RECOMMENDED ACCESSORIES.

Consult this manual or manufacturer

for recommended accessories. Using

improper accessories will increase risk of

serious injury.

MAINTAIN WITH CARE. Keep cutting

tool edges sharp and clean. Follow all

maintenance instructions and lubrication

schedules to keep tool in good work-

ing condition. A tool that is improperly

maintained could malfunction, leading to

serious personal injury or death. Only

have tool serviced by qualified service-

personnel using matching replacement

parts.

CHECK DAMAGED PARTS. Regularly

inspect tool for any condition that may

affect safe operation. Immediately repair

or replace damaged or mis-adjusted parts

before operating tool.

MAINTAIN POWER CORDS. When dis-

connecting cord-connected tools from

power, grab and pull the plug—NOT the

cord. Carrying or pulling the cord may

damage wires inside. Do not handle cord/

plug with wet hands. Avoid cord damage

by keeping it away from heated surfaces,

high traffic areas, harsh chemicals, sharp

edges, moving parts, and wet/damp loca-

tions. Damaged cords increase risk of

electrocution.

UNATTENDED OPERATION. Never

leave tool running while unattended. Turn

tool OFF and ensure all moving parts

completely stop before walking away.

EXPERIENCING DIFFICULTIES.

If at

any time you experience difficulties per-

forming the intended operation, stop

using the machine! Contact our Technical

Support at (570) 546-9663.

Model T33304 (Mfd. Since 05/22) -3-

Additional Safety for Routers

Amputation, serious cuts, entanglement, or death can occur from contact with

rotating cutterhead or other moving parts! Flying chips can cause eye injuries

or blindness. Knives/inserts thrown by cutterhead can strike nearby operator or

bystanders with deadly force. To reduce the risk of these hazards, operator and

bystanders MUST completely heed hazards and warnings below.

POWER SOURCE. Remove battery from

the router before inserting or removing

bit, making adjustments, or performing

maintenance or service. DO NOT make

adjustments while the router is connected

to battery.

ROUTER BITS. Inspect router bits before

use. DO NOT use router bits that have

been dropped, cracked, or damaged.

The router bit may shatter, causing seri-

ous injury.

COLLET WRENCHES. Make sure the

collet wrenches are removed from the

router before inserting battery and turning

router ON.

AVOIDING BIT CONTACT. Keep unused

portion of bit above base or guide. Always

keep some type of guard or other protec-

tive device between your hands and bit

at all times!

ROUTING. Always route with the base

flat upon the workpiece. DO NOT start

the router with the bit in contact with the

workpiece.

REMOVING BIT. The bit is sharp and

will be hot after use. Use gloves when

removing.

PROTECT HANDS/FINGERS. While

feeding workpiece, avoid awkward hand

positions. Never pass hands directly

under, or in front of, bit. Keep hands away

from bit. Hold the router with both hands

to control torque twist and kickback.

FEEDING DIRECTION. Always feed the

router against the cutter rotation. DO

NOT start routing at a corner. Starting at

a corner may cause the router to grab,

damaging the workpiece, and possibly

causing personal injury.

CUTTING DEPTH. Never attempt to

remove too much material in one pass.

Doing this increases risk of workpiece

kickback. Instead, make several light

passes—this is a safer way to cut and it

leaves a cleaner finish.

WORKPIECE CONDITION. Routing a

workpiece with knots, holes, or foreign

objects increases risk of kickback and bit

damage/breakage. Thoroughly inspect

and prepare workpiece before rout-

ing. Rough, warped, or wet workpieces

increase risk of kickback.

SAFE BIT CLEARANCES. Operator or

bystanders may be hit by flying debris

if cutter contacts fence, guard, or table

insert upon startup. Always ensure any

new cutter setup has proper cutter rota-

tional clearance before startup.

SAFE BIT INSTALLATION. Improperly

secured bits or other inserts may become

dangerous projectiles if they come loose.

Always ensure collet and collet nut are

tight.

AVOIDING CLIMB CUTS. Feeding

workpiece in same direction of bit rotation

is a “climb cut.” Climb cutting can aggres-

sively pull workpiece—and hands—into

bits. Always first verify direction of bit

rotation before starting, and always feed

workpiece AGAINST bit rotation.

SAFETY GUARDS. To reduce risk of

unintentional contact with bit, always

ensure included bit guard is correctly

positioned before operation.

SAFETY EQUIPMENT. Wear safety

glasses, respirator, and hearing protec-

tion when operating a router.

Model T33304 (Mfd. Since 05/22)-4-

Additional Safety for Batteries & Chargers

Battery and charger components may cause irritation, burns, electric shock or

fire if disassembled, damaged, stored incorrectly, or disposed of incorrectly.

Connecting charger to circuit it is not rated for could result in fire or explosion.

To reduce the risk of these hazards, operator and bystanders MUST completely

heed hazards and warnings below.

READ ENTIRE MANUAL. Read and

understand all of the instructions and

warnings before charging battery.

CHARGING EQUIPMENT. Only charge

battery using charger and battery

supplied with tool. DO NOT use batteries

or chargers from other cordless tools.

CHARGING ENVIRONMENT. Charge

battery on dry, hard surface in shad-

ed location with good ventilation. DO

NOT place charger on or near flam-

mable materials. DO NOT cover charger

when charging. DO NOT expose

charger to moisture. Only charge

battery when temperature is between

50°F (10°C)–104°F (40°C). Charging in

temperatures beyond these extremes will

damage battery.

DO NOT DISASSEMBLE BATTERY OR

CHARGER. Tampering with battery or

charger may result in risk of electric shock

or fire.

CHARGER DAMAGE. Replace charger if

it has been dropped, damaged, exposed

to liquid, or has received hard impact.

DISCONNECT CHARGER. Unplug

charger when cleaning, or when not in

use.

SHORTING BATTERY. Avoid touching

terminals with skin or metal, to prevent

injury from an electrical shock and to

prevent fire from spark. Do not store bat-

tery with metal objects that could create

connection between terminals or in place

where it could get wet.

CHARGER VOLTAGE. DO NOT plug

into circuit that charger is not rated for.

Connecting charger to circuit with incor-

rect voltage will damage charger, possibly

causing fire or explosion. DO NOT charge

from DC power supply or generator or with

extension cord.

DAMAGED BATTERY. Regularly inspect

battery for any damage, corrosion, or any

condition that may affect safe operation.

Immediately replace damaged battery

before operating tool.

BATTERY DISPOSAL. Battery must be

recycled or disposed of properly. DO NOT

dispose of battery in landfill or incinerate.

Combustion of some of battery's compo-

nents can cause toxic fumes and possible

explosion.

BATTERY LIQUID. Liquid contained in

batteries can cause irritation or burns.

If liquid contacts eyes or skin, flush with

water and seek medical assistance.

No list of safety guidelines can be complete. Every shop environment is different.

Always consider safety first, as it applies to your individual working conditions.

Use this and other machinery with caution and respect. Failure to do so could

result in serious personal injury, damage to equipment or poor work results.

Model T33304 (Mfd. Since 05/22) -5-

SECTION 2: INTRODUCTION

We are proud to offer this manual with

your new router! We've made every effort

to be exact with the instructions, specifica-

tions, drawings, and photographs of the

router we used when writing this manual.

However, sometimes we still make an

occasional mistake.

Also, owing to our policy of continuous

improvement, your router may not exactly

match the manual. If you find this to be

the case, and the difference between the

manual and router leaves you in doubt,

check our website for the latest manual

update or call technical support for help.

For your convenience, we post all avail-

able manuals and manual updates for

free on our website at www.grizzly.com.

Any updates to your model of tool will be

reflected in these documents as soon as

they are complete.

Foreword

Charging Source ............................................................................................................120V

Battery Type .................................................................................................. 20V Lithium-Ion

Collet Size .................................................................................................................... 1/4 in.

Maximum Plunge Depth .................................................................................................. 2 in.

Length x Width x Height ........................................................................ 6 x 5-1/4 x 10-1/2 in.

Dust Port Size ........................................................................................................... 1-1/2 in.

Speed Range ...........................................................................................8000 - 26000 RPM

Weight .........................................................................................................................6.8 lbs.

Specifications

Contact Info

We stand behind our machines. If you

have any service questions, parts requests

or general questions about the machine,

please call or write us at the location listed

below.

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: (570) 546-9663

E-Mail: techsupport@grizzly.com

We want your feedback on this manual.

If you can take the time, please email or

write to us at the address below and tell

us how we did:

Grizzly Industrial, Inc.

C/O Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

Model T33304 (Mfd. Since 05/22)-6-

Identification

Become familiar with the names and locations of the controls and features shown below to

better understand the instructions in this manual.

To reduce your risk of

serious injury, read

this entire manual

BEFORE using Tool.

A. Start/Stop Button

B. Power Lock Button

C. Battery Lock

D. Speed Dial

E. Depth Stop Rod

F. Battery (not included)

G. Depth Adjustment Nut

H. Router Base Lock Knob

I. Guide Lock Knobs

J. Router Plunge Base

K. Dust Port Lock Knob

L. 8-Position Depth Stop Block

M. Spindle Lock Button

N. Plunge Lock Lever

O. Plunge Base Handles (1 of 2)

P. Router Motor

Q. Depth Stop Lock Knob

R. Chip Guard

S. Dust Port

T. Collet Nut

U. Collet

V. Depth Scale

Model T33304 (Mfd. Since 05/22) -7-

Controls &

Components

Refer to Figures 1–4 and the following

descriptions to become familiar with the

basic controls of this tool.

To reduce your risk

of serious injury, read

this entire manual

BEFORE using tool.

C. Speed Dial: Choose from 6 speed set-

tings on dial. Move dial left for higher

speeds and right for slower speeds.

Speed Setting RPM

18,000

211,6 00

315,200

418,800

522,400

625,400

Figure 2. Speed dial.

A. Start/Stop Button: With tool in stand-

by mode, press once to start motor.

B. Power Lock Button: Press once to

unlock tool and enter standby mode.

Press again to lock tool and exit stand-

by mode. Tool can only be started in

standby mode.

Note: Pressing either Start/Stop Button

or Power Lock Button will turn the tool

OFF.

Note: If left in standby mode for more

than 10 seconds, tool will automatically

turn itself OFF.

Figure 1. Power controls.

Model T33304 (Mfd. Since 05/22)-8-

D. Depth Adjustment Nut: Provides fine

control of bit height.

E. Depth Stop Lock Knob: Secures

desired cut height when locked.

F. 8-Position Depth Stop Block: Rotates

to different heights for setting depth of

cut. Used in conjunction with depth

stop rod.

G. Depth Scale: Measures depth of router

plunge travel.

H. Plunge Lock Lever: Controls move-

ment of plunge mechanism. Move

down to lock plunge mechanism, move

up to release.

I. Collet: Holds bit.

J. Spindle Lock Button: Locks spindle in

place for bit installation and removal.

K. Collet Nut: Secures collet and bit tool

on spindle.

Figure 4. Spindle and collet controls

Figure 3. Depth controls.

Inhaltsverzeichnis

Andere Grizzly Holzfräse Handbücher

Grizzly

Grizzly T31636 Bedienungsanleitung

Beliebte Holzfräse Handbücher anderer Marken

Stanley

Stanley SRR1200-RU Bedienungsanleitung

Wolfcraft

Wolfcraft MASTER RT 540 Bedienungsanleitung

Worx Professional

Worx Professional WU600 Bedienungsanleitung

Proxxon

Proxxon BFW 40/E Bedienungsanleitung

Porter-Cable

Porter-Cable 893PK Bedienungsanleitung

Ryobi

Ryobi R181D Bedienungsanleitung

Clarke

Clarke Contractor CR3 Bedienungsanleitung

Vision Engraving & Routing Systems

Vision Engraving & Routing Systems 1624R Bedienungsanleitung

Triton

Triton TMNRTR Montageanleitung

Status

Status RH1800 Bedienungsanleitung

Asist

Asist AE4F120DN Bedienungsanleitung

Sealey

Sealey SV20 Series Bedienungsanleitung

Makita

Makita 3606 Bedienungsanleitung

RIDGID

RIDGID R2901 Bedienungsanleitung

Hitachi Koki

Hitachi Koki M 12V2 Bedienungsanleitung

Promaker

Promaker PRO-RT1600 Bedienungsanleitung

Wen

Wen RT1460 Bedienungsanleitung

Mafell

Mafell LO 50 E Leitfaden