Grundfos KJI K Series Installationsanleitung

r e v i s i o n 0.0

K-Series

Instruction & Operation

Manual for KJI PUMPS

750-18, Jangnok-dong, Gwangsan-gu

Gwangju, Korea

Tel : 82-62-602-8400 (Rep.)

Web : www. kjipumps.co.kr

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 2 / 25

TABLE of CONTENTS

1. Overview

2. General Data

2.1 Information of the nameplate

2.2 Pump code designation

2.3 Maximum operating conditions

2.4 Safety Precautions

2.5 Applications

2.6 Operating Conditions

3. Carriage & Transport

3.1 Lifting the pump

Storage

4.1 Warehouse storage

4.2 Storage in the pit-system not in use

5. Installation

5.1 Points for attention during installation

5.2 Cable joints

5.3 Wet pit ADC installation

5.4 Dry pit installation

5.5 Portable installation

5.6 Horizontal installation

6. Commissioning & Operation

6.1 Initial Examination

6.2 Precautions

6.3 Insulation check

6.4 Control panel wiring

6.5 Thermal protection wiring

6.6 Changing the direction of rotation

6.7 Level switch & General wiring

7. Maintenance, Inspection and Overhaul

7.1 Maintenance

7.2 Inspection

7.3 Overhaul

8. Trouble Shooting

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 3 / 25

KSE & KSN USER MANUAL

OVERVIEW

Thank you for choosing KJI Pumps. This manual is designed to help you achieve the

best results from our products in terms of longevity, efficient usage and maintenance.

All users should read and be familiar with the contents of this manual.

All faults resulting from failure to install or maintain our product as described in this

handbook will be deemed to be faults arising from misuse of the product not covered

by warranty.

For any clarification required related to the contents of this manual, please contact KJI

office. Retain this manual for future reference.

GENERAL DATA

2.1 Information of the nameplate

All pumps can be identified by means of the nameplate on the top cover or frame of

the motor, see fig.1.

If the nameplate is damaged, the pump will be identified by the serial number

stamped on the nameplate.

Model No.

max

Motor

min

-1

Date

Temp. C

max

IP68

Isol.Class

/kW Cos.

VY AV

Manufactured for

11 12

13 14 15

16 16 17 17

Serial No.

Pos.

Description

1 Serial number

2 Production date

3 Pump code

4 Maximum liquid temperature

5 Design head

6 Design flow

7 Low water level

8 Motor speed

9 Weight of the pump

10 Number of phases

11 Frequency

12 Insulation class

13 Power input

14 Shaft power

15 Power factor

16 Voltage/current

D.O.L connection

17 Voltage/current

Star-delta connection

fig.

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 4 / 25

2.2 Pump code designation.

S 200 K S E 37 4 T 3

Volatage : 2=220V,230V / 3=380V / 4=415V,460V upto 6600V

Phase : S=Single Phase, T=Three Phase

Number of Poles : (Motor Synchronous Speed at 50Hz)

2=2850rpm, 4=1450rpm, 6=950rpm,

8=720rpm, 10=580rpm...etc

Motor Output in kW : (Horsepower Output=kW x 1.341)

Impeller Type : E=Enclosed, O=Open, V=Vortex,

SV=Semi-Vortex, PL:Propeller, M=Mixed

Pump Type : S=Sewage, W=Wastewater, D=Drainage,

A=Agitator, R=Aerator, M=Mixer

Manufacturer's Designation : K=K-Series

Discharge Size in mm

Materials of Construction : Blank=Standard Construction

S=All Stainless Steel, B=All Bronze

2.3 Maximum operating conditions.

The K-series submersible pumps are designed for pumping of unscreened wastewater

in municipal and industrial installations and for low to medium density sludge

pumping in sewage treatment plants. The pumps are also suitable for various raw

water pumping duties where the conditions call for submersible pumps to be installed.

Different pump material specifications are available for use in corrosive liquids.

Pump usage is restricted by the following ambient conditions used as design criteria

limits:

-Maximum ambient and pumped liquid temperature is 40℃

-Storage temperature range is – 20℃… + 50℃

-Maximum allowable voltage fluctuation is ± 10% ~5% of nominal voltage

-Maximum submergence is 20 m.

ATTENTION!

Usage of the pumps in installations where conditions exceed those allowed in the

pump specifications may lead to pump malfunction and damage.

2.4 Safety Precautions

This pump contains hazardous moving parts. To prevent risk of injury, disconnect

power before servicing. Never put fingers near impeller when pump is connected to a

power source.

Installation should be performed by technicians with the appropriate qualifications as

required by local legislation.

This pump has not been approved for use in swimming pools and it should not be

installed in this type of application.

fig. 2

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 5 / 25

Do not work alone. Use proper safety equipment including antiseptic masks if

necessary.

Ensure that there is no toxic or explosive gas in the wet well before entering or

welding or using electric tools.

Use approved lifting equipment and slings and do not stand under the pump while it

is being lifted. The cable is not designed to lift the pump and the pump must not be

maneuvered by use of the cable.

Ensure the cable particularly the exposed end is kept dry during installation.

The use of an earth leakage circuit breaker is highly recommended and may be

mandatory under local regulations. Please check local requirements.

2.5 Applications

KJI Pumps are designed for the pumping of sewage and wastewater in a wide range

of municipal and industrial applications.

Depending on the installation type, the pumps can be used for submerged or dry,

horizontal or vertical installation. Maximum solids size can be changed, depending

on impeller type.

KJI Pumps Description Accessories

K-Series

-Waste Water

Municipal Sewage Treatment Plants

-Storm Water

-Industrial Effluent

Process Water Handling

-ADC, Flange

-Hose coupling

-Cooling Jacket

-Explosion proof

-Smart Lift

2.6 Operating conditions

2.6.1 pH value

All pumps can be used for pumping liquids with a pH value between 6 and 10.

-Liquid temperature(0°C to +40°C)

-Explosion-proof pumps must never pump liquids with a temperature

higher than +40°C.

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 6 / 25

2.6.2 Ambient temperature(0°C to +40°C)

-For explosion proof pumps, the ambient temperature on the installation

site must be in the range between 0°C to +40°C.

2.6.3 Level of pumped liquid

• For pumps fully submerged pumps without cooling jacket, the lowest stop level

must be above the stator housing.

-The pump weight is stated on the pump nameplate.

• Install an additional level switch to ensure that the pump is stopped in case the

stop level switch is not operating.

• For a short period of time it is allowed to use the pump to pump down the water

level to remove the float layer. For explosion proof pumps it is not allowed to

go below the stop levels.

• For a submerged pump, the lowest stop level must always be above the pump

housing. To ensure adequate cooling of the motor during operation, the

following minimum requirements must be met :

-For continuous operation, the pump must always be covered by the

pumped liquid to the top of the motor

fig.

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 7 / 25

-For intermittent operation, the pump must always be covered by the

pumped liquid to the middle of the motor

3. CARRIAGE & TRANSPORT

During transportation the pump should be secured in such a manner as to avoid

shocks which may damage the pump.

Handle the pump carefully. Use the lifting eye provided or slings the pump from the

body and moves the pump with the aid of a hoist or proper handling equipment.

The pump should never be moved by the cable. There is a high possibility of

damage which may result in an electric short and risk of shock. The cable and cable

inlet may be damaged leading to loss of water tightness and subsequent severe

damage to the motor.

3.1 Lifting the pump

• KJI pumps approximately weigh up to 10,000 kg without accessories. It is

therefore important to use the right lifting equipment.

-The pump weight is stated on the pump nameplate.

• All lifting equipment must be rated for the purpose and checked for damage

before any attempt to lift the pump. The lifting equipment rating must under no

circumstances be exceeded.

• Always lift the pump by the marked lifting points or by designated equipment.

Never lift the pump by the power supply cables. It may result in electric short-

circuit and risk of electric shock when the pump is connected to the mains. The

cables and cable entry may be damaged, leading to loss of water tightness and

consequent severe damage to the motor.

4. STORAGE

4 .1 Warehouse Storage

• The warehouse must be free of excessive humidity, corrosive gases or vapours

and free from vibration which might damage the pumps.

• Store the pumps in a vertical position on a pallet or stand to keep the pump off

the floor and facilitate easy removal.

• The cable should be coiled and the open end should be tightly sealed with

waterproof plastic and tape or a cable cap to prevent the penetration of moisture

which may reach the motor and cause severe damage to the windings.

• All unpainted surfaces should be given a light coat of oil or grease to prevent

corrosion.

• If the pumps is being stored for longer than two months the impeller must be

turned by hand at least every two months to prevent the lower mechanical seal

faces from seizing up.

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 8 / 25

• For long periods of storage the pump must be protected against moisture and

heat.

• Make sure the cooling jacket is empty before storing the pump.

• After a long period of storage, inspect the pump before putting it into operation.

Make sure that the impeller can rotate freely. Pay special attention to the

condition of the shaft seals and the cable entry.

4.2 Storage in the pit-system not in use

If an installed pump is not in operation for an extended period of time, the insulation

resistance should be measured and the pump runs for 30 mins each month.

If the pump cannot be run due to lack of water in the sump it should be inspected and

turned over by hand each month & prior to being put back into service. If the

insulation resistance drops below 10 Mega-Ohm, contact your local Grundfos office.

The power source must be shut off and isolated at the control panel when the pump is

not in service

If the pump is disconnected from the control panel when not in service, the cable end

should be tightly sealed.

5. INSTALLATION

5.1 Points for attention during installation

• Check that the dimensions of the sump are correct and large enough so that the

pump can be installed and removed for servicing.

• Thoroughly clean and remove all rubbish from the sump and general

installation area to prevent clogging the impeller causing possible motor failure.

• Check the accessories and controls are complete.

• Carry the pump only as described in Clause 3.

• The extra nameplate supplied with the pump should be fixed at the installation

site.

• All safety regulations must be observed at the installation site, for instance the

use of blowers for fresh air supply.

• Prior to installation, check the oil level in the oil chamber.

• The start and stop levels are specified during the design stage. Always check

that the start/stop levels function and possibly alter them when commissioning

the pump in order to ensure good operation .

• To ensure adequate pull-out strength we recommend to use anchor bolt.

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 9 / 25

To prevent mechanical damage,all cables laid under ground must be properly

installed in underground electrical conduit specifically designed for this purpose,

cables must not be installed directly in the ground or in

concrete. (see fig. 4).

The pump must be earthed by connecting the earth (green) wire. Verify the

grounding continuity by checking that the grounding wire (green, labelled

as “E”) is electrically conductive with the bolt on the motor (paint to be stripped).

Ensure all electrical cables are securely supported and that there is no loose cable

which could be sucked into the pump inlet.

After installing the pump, secure the lifting chain or wire rope to a wall or other

rigid surface, outside of the pit, to prevent submerged in wastewater.

fig. 5

fig.

K-Series

I/O Manual

Prepared by.

Rev. No. 0

Date. 11-Jan-11

Page. 10 / 25

5.2 Cable Joints

If it is necessary to extend the pump supply cable ensure that the cross sectional area

of the extension cable used keeps sufficient cross sectional area to absorb voltage

drop. Ensure that the cable joint is waterproof and secure.

Connect each pair of wires (R-U, S-V, T-W) using a Sleeve Joint and staggering the

joints as shown below in fig. 5.

Primary Insulation layer:

Paste each individual wire joint with glue and wind with a strip of natural rubber.

Then wind with waterproof vinyl.

Secondary Insulation layer:

Gather together all the individual wires into one cable and repeat the above insulating

procedure on the complete cable ensuring that the insulation covers the original cable

insulation at both ends by a minimum of 220mm.

The thickness of the joint must be less than twice the original cable diameter.

5.3 Wet pit ADC installation

In the Wet pit installation, the pump is installed on

the Automatic Discharge Connection (ADC) and

operates completely or partially submerged in the

pumped liquid.

fig. 6

fig. 7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Grundfos Wasserpumpe Handbücher

Grundfos

Grundfos NK Bedienungsanleitung

Grundfos

Grundfos MQ 3-25 Bedienungsanleitung

Grundfos

Grundfos NKG Series Bedienungsanleitung

Grundfos

Grundfos MTH Series Bedienungsanleitung

Grundfos

Grundfos DSS Bedienungsanleitung

Grundfos

Grundfos GT-C Bedienungsanleitung

Grundfos

Grundfos TP 32-40 Bedienungsanleitung

Grundfos

Grundfos Conlift1 LS Bedienungsanleitung

Grundfos

Grundfos SE Bedienungsanleitung

Grundfos

Grundfos MTA 110H-180 Bedienungsanleitung

Grundfos

Grundfos Unilift KP 150 Bedienungsanleitung

Grundfos

Grundfos NK Series Bedienungsanleitung

Grundfos

Grundfos CMBE TWIN Bedienungsanleitung

Grundfos

Grundfos JP Booster PS Series Bedienungsanleitung

Grundfos

Grundfos CM Smart Bedienungsanleitung

Grundfos

Grundfos CRE Series Bedienungsanleitung

Grundfos

Grundfos UPE Series Bedienungsanleitung

Grundfos

Grundfos JP Series Bedienungsanleitung

Grundfos

Grundfos Unilift AP12 Bedienungsanleitung

Grundfos

Grundfos MAGNA 2000 Series Bedienungsanleitung

Grundfos

Grundfos NB Series Bedienungsanleitung

Grundfos

Grundfos AC Series Bedienungsanleitung

Grundfos

Grundfos PS.R.05 Bedienungsanleitung

Grundfos

Grundfos MSS Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung