Grundfos SQFlex 11 SQF-2 Bedienungsanleitung

Installation and op erating instructions

Notice d’installation et d’entretien

Instrucciones de instalación y funcionamiento

GRUNDFOS INSTRUCTIONS

LIMITED WARRANTY

Products manufactured by GRUNDFOS PUMPS CORPORATION (Grundfos) are warranted

to the original user only to be free of defects in material and workmanship for a period

of 24 months from data of installation, but not more than 30 months from data of manu-

facture. Grundfos’ liability under this warranty shall be limited to repairing or replacing

at Grundfos’ option, without charge, F.O.B. Grundfos’ factory or authorized service

station, any product of Grundfos’ manufacture. Grundfos will not be liable for any costs

of removal, installation, transportation, or any other charges which may arise in connec-

tion with a warranty claim. Products which are sold but not manufactured by Grundfos

are subject to the warranty provided by the manufacturer of said products and not by

Grundfos’ warranty. Grundfos will not be liable for damage or wear to products caused

by abnormal operating conditions, accident, abuse, misuse, unauthorized alteration or

repair, or if the product was not installed in accordance with Grundfos’ printed installa-

tion and operating instructions.

To obtain service under this warranty, the defective product must be returned to the

distributor or dealer of Grundfos’ products from which it was purchased together with

proof or purchase and installation date, failure date, and supporting installation data.

Unless otherwise provided, the distributor or dealer will contact Grundfos or an author-

ized service station for instructions. Any defective product to be returned to Grundfos or

a service station must be sent freight prepaid; documentation supporting the warranty

claim and/or a Return Material Authorization must be included if so instructed.

GRUNDFOS WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES,

LOSSES, OR EXPENSES ARISING FROM INSTALLATION, USE, OR ANY OTHER CAUSES. THERE

ARE NO EXPRESS OR IMPLIED WARRANTIES, INCLUDING MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE, WHICH EXTEND BEYOND THOSE WARRANTIES DESCRIBED

OR REFERRED TO ABOVE.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential

damages and some jurisdictions do not allow limit actions on how long implied warran-

ties may last. Therefore, the above limitations or exclusions may not apply to you. This

warranty gives you specific legal rights and you may also have other rights which vary

from jurisdiction to jurisdiction.

Installation and

operating instructions

Page 4

Notice d’installation

et d’entretien

Page 14

Instrucciones de instalación

y funcionamiento

Pág. 24

CONTENTS

Page

1. General description 4

1.1 Applications 4

1.2 Type key 4

1.3 MQ pump 5

2. Pumped liquids 5

3. Technical data 5

3.1 Operating conditions 5

3.2 Electrical data 6

3.3 Dimensions 6

3.4 Approvals 6

4. Functions 6

4.1 Control panel 6

4.2 Pump stop 8

5. Mounting and connection 8

5.1 Mounting the pump 8

6. Electrical connection 9

6.1 Generator or inverter 9

6.2 Wiring diagram 10

6.3 Winding resistance measurement 10

6.4 Start-up 11

7. Main

tenance 1

7.1 Service kits 11

7.2 Start-up after a long time of inactivity 11

8. Service 11

9. Disposal 11

10. Fault finding chart 12

Dimensions 35

Before beginning installation procedures,

these installation and operating instruc-

tions should be studied carefully. The instal-

lation and operation should also be in

accordance with local regulations and ac-

cepted codes of good practice.

1. General description

The MQ is a compact water supply system consisting

of a pump, motor, pressure tank and controller com-

bined in an integral unit.

The pump starts automatically when water is con-

sumed in the installation and stops when the con-

sumption ceases. The MQ is a low-noise pump which

can be installed both indoors and outdoors.

Note: When installed outdoors the MQ should not be

exposed to direct sunlight or rain.

The pump is self-priming and has a check valve incor-

porated in the discharge port, see fig. 1. The pump

features a user-friendly control panel.

The pressure tank incorporated in the pump reduces

the number of starts and stops in case of leakage in

the installation.

The MQ pump has built-in overtemperature and dry-

running protection.

1.1 Applications

Typical applications:

• Water pressure boosting

(maximum inlet pressure: 45 psi) and

• water supply from wells (maximum suction lift:

25 ft), e.g.

- in private homes,

- in summer houses and weekend cottages,

- on farms,

- in market gardens and other large gardens.

The pump can be used for rain water and has been ap-

proved for drinking water.

The maximum suction lift of the pump can be deter-

mined from the diagram on page 35.

Example:

If the suction lift is 10 ft, the length of the suction

pipe must not exceed 72 ft.

1.2 Type key

Example MQ 3 -35 A -O -A BVBP

Pump type

Nominal flow rate [m³/h]

Head [m]

Code for pump version

A: Standard

Code for pipework connection

Code for materials

A: Standard

Code for shaft seal

1.3 MQ pump

Fig. 1

2. Pumped liquids

Thin, clean, non-aggressive liquids, not containing

solid particles or fibres.

3. Technical data

3.1 Operating conditions

TM01 9873 2600

Suction port

Drain plug

Base plate

Priming plug

Discharge port Pressure tank

Control panel

Plug

MQ 3-35 MQ 3-45

Maximum flow rate [gpm] 22

Maximum pressure [psi] 51 65

Maximum system pressure [psi] 108

Maximum suction lift [ft], see page 35 25

Minimum ambient temperature [°F] 32

Maximum ambient temperature [°F] 113

Minimum liquid temperature [°F] 32

Maximum liquid temperature [°F] 95

Net weight [lbs] 29

Sound pressure level [dB(A)] < 70

Tank volume [oz] 5

Air pressure in tank [psi] 22 to 25

Connections 1" NPT

3.2 Electrical data

3.3 Dimensions

See dimensions at the end of these instructions.

3.4 Approvals

Materials in contact with the pumped liquid have

been approved by the British Water Regulations

Advisory Scheme (WRAS) according to BS 6920 for use

in drinking water.

Other approvals: See pump nameplate.

4. Functions

4.1 Control panel

The MQ pump is operated entirely by means of the

control panel, see fig. 2. The control panel offers the

possibility of starting/stopping the pump. The pump

settings and operating condition are indicated by in-

dicator lights.

Fig. 2

MQ 3-35 MQ 3-45

Enclosure class IP 54

Insulation class B

Supply cable 6.56 ft H07RN-F with/without plug

Voltage,

power consumption, P1[W]

1 x 110-120 V –10/+6%, 60 Hz 800/7.2 A 1000/9.2 A

1 x 220-240 V –10/+6%, 60 Hz 850/3.7 A 1050/4.5 A

TM01 9684 2600

The functions of the control panel are described in the following table:

Note: The pump settings are stored. After supply failure, the pump will automatically revert to its previous oper-

ating condition when the electricity supply is connected again.

Illustration Description

1Indicator light (red):

When the indicator light is on, the pump is on standby.

2On/off button:

The pump is started/stopped by means of the on/off button.

The on/off button can also be used for manual resetting in case

of an alarm condition:

• press once for resetting and

• press once more for starting.

3Indicator light (green):

Indicates that the pump is ready for operation.

When the indicator light is on, the pump will start automati-

cally when water is consumed. The pump will stop a few sec-

onds after the water consumption has ceased.

4Pump on (green):

The indicator light is on when the pump is running.

5Auto-reset (green):

As standard, this function is activated on delivery (does not

apply to pump versions for Australia).

When the indicator light is

• on, the Auto-reset function is activated. The pump will auto-

matically attempt to restart every 30 minutes after an alarm/

fault over a period of 24 hours. After this period, the pump

will remain in the alarm condition.

• off, the Auto-reset function is deactivated. The pump will not

restart after an alarm/fault.

The Auto-reset function can be activated/deactivated by press-

ing the on/off button for 5 seconds.

Note: When water is consumed, the pump will start and stop

automatically, whether the Auto-reset light is on or off.

6Alarm (red):

The indicator light is on when the pump is in alarm condition.

The alarm condition may have been caused by:

• dry running,

•overtemperature,

• overloaded motor or

• seized-up motor/pump.

See section 4.2 Pump stop.

4.2 Pump stop

The pump incorporates an electronic protective func-

tion which will stop the pump in case of

• dry running,

• overtemperature,

• overloaded motor or

• seized-up motor/pump.

The pump will restart automatically after 30 minutes

(for 24 hours) in case of any type of fault if the Auto-

reset function is activated (the green indicator light

on the control panel is on, see point 5 in the table in

section 4.1 Control panel).

5. Mounting and connection

5.1 Mounting the pump

The pump is resistant to sunlight and can be installed

both indoors and outdoors. When installed outdoors,

it is recommended to protect the pump by means of a

suitable cover.

Always mount the pump on the base plate with hori-

zontal suction port and vertical discharge port.

The pump must be mounted horizontally.

Maximum permissible inclination angle: ±18°, see

fig. 3.

Fig. 3

The pump must be secured to a solid foundation by

bolts through the holes in the base plate, see fig. 4.

Fig. 4

The pump discharge is flexible, ±5°, to facilitate the

connection. Never apply unnecessary force when con-

necting the pipes.

The pump is supplied with 1" NPT screwed connec-

tions to be fitted in the suction and discharge ports,

see fig. 5.

Fig. 5

The pump incorporates a check valve which prevents

backflow during priming and operation.

Installations with long suction pipes: A check valve is

supplied with the pump. It is recommended to fit this

check valve in the pump suction port.

If the pump is installed in long pipes, the pipes must

be adequately supported on either side of the pump

in order not to strain the pump connections. If the

pump draws water from a well, it is recommended

also to fit a foot valve to the end of the suction pipe,

see fig. 6.

Fig. 6

If a hose is used for suction pipe, it must be of a non-

collapsible type.

As the pump is self-cooling, no space is required

around the pump and no ventilation is required.

TM01 9691 2600

TM01 9692 2600

Max. ±18°

7.5 inch

4.5 inch

TM01 9698 2600

TM01 9693 2600

Foot valve

6. Electrical connection

The electrical connections and additional protection

should be carried out by qualified persons in accor-

dance with local regulations.

The operating voltage and frequency are marked on

the nameplate. Make sure that the motor is suitable

for the electricity supply on which it will be used.

The pump must be connected to the mains via a rub-

ber-sheathed cable with a protective ground lead. It is

possible to replace the mains supply cable, see fig. 7.

Fig. 7

Connect the mains supply cable of the pump to the

electricity supply. When the cable is connected, a red

and a green indicator light on the control panel will be

on, see fig. 8.

Fig. 8

* Does not apply to pump versions for Australia.

6.1 Generator or inverter

Note: The MQ can be powered by a generator or an in-

verter. However, the pump will only operate satisfac-

torily if the generator or inverter generates a true

sinusoidal wave with the necessary power and volt-

age input.

Never make any connections in the

pump terminal box unless the elec-

tricity supply has been switched off for

at least 5 minutes.

Risk of electric shock: This pump is sup-

plied with a grounding conductor and

grounding type attachment plug. To

reduce the risk of electric shock, be cer-

tain that it is connected only to a

properly grounded electrical circuit

equipped with a ground fault inter-

rupter device.

This pump is not intended, nor has it

been investigated for use in swimming

pool areas.

This pump has been evaluated for use

with water only.

Do not start the pump until it has been

filled with water (primed, see fig. 9).

For indoor use only.

TM01 9694 2600

TM01 9695 2600

6.2 Wiring diagram

Fig. 9

6.3 Winding resistance measurement

The measurement can be done with or without cables connected to the PCB and the capacitor.

TM02 2424 4303

Capacitor

Electric motor

White (aux.)

Red (main)

Blue

Yellow/green

Ground

ase

Neutral

Brown

Blue

range

Black

Red

=> Mains

=> Flow sensor

=> Pressure switch

Red

Motor

[V/Hz] Measuring point Winding Resistance

[Ω ±10%]

Ambient temperature

[°C] [°F]

230/50 A-B Main 6.4

21 70

230/60 A-C Aux 16.7

120/60 A-B Main 1.5

A-C Aux 6.1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Grundfos Wasserpumpe Handbücher

Grundfos

Grundfos TPE Series Betriebsanleitung

Grundfos

Grundfos KPL Bedienungsanleitung

Grundfos

Grundfos Unilift CC 5 Bedienungsanleitung

Grundfos

Grundfos SCALA 2 Original Betriebsanleitung

Grundfos

Grundfos NB Series Bedienungsanleitung

Grundfos

Grundfos NB Series Bedienungsanleitung

Grundfos

Grundfos COMFORT PM Bedienungsanleitung

Grundfos

Grundfos CMB-SP Booster PM2 Bedienungsanleitung

Grundfos

Grundfos Sololift+ C-3 Bedienungsanleitung

Grundfos

Grundfos SB Series Bedienungsanleitung

Grundfos

Grundfos SL Series Bedienungsanleitung

Grundfos

Grundfos ALPHA Pro Bedienungsanleitung

Grundfos

Grundfos seg autoadapt Original Betriebsanleitung

Grundfos

Grundfos DW Series Bedienungsanleitung

Grundfos

Grundfos MAGNA1 D Bedienungsanleitung

Grundfos

Grundfos Conlift1 LS Bedienungsanleitung

Grundfos

Grundfos SCALA1 Bedienungsanleitung

Grundfos

Grundfos UP15-42F Betriebsanleitung

Grundfos

Grundfos Hydro 1000 Bedienungsanleitung

Grundfos

Grundfos rmq-a Bedienungsanleitung

Grundfos

Grundfos ALPHA 1 Bedienungsanleitung

Grundfos

Grundfos MAGNA 2000 Series Bedienungsanleitung

Grundfos

Grundfos MAGNA1 D Bedienungsanleitung

Grundfos

Grundfos SLV.65 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung