Grundfos Unilift CC 5 M1 Betriebsanleitung

Service instructions

Unilift CC

1 / 8

96581224 0406 GB 8

Contents

1. Identification .................................................................................................................................... 2

1.1 Nameplate ......................................................................................................................................... 2

1.2 Type key............................................................................................................................................ 2

2. Fault finding..................................................................................................................................... 3

3. Cleaning the pump .......................................................................................................................... 4

3.1 Cleaning the suction strainer............................................................................................................. 4

3.2 Cleaning the impeller......................................................................................................................... 4

4. Dismantling and assembly ............................................................................................................. 5

4.1 Removing the motor .......................................................................................................................... 5

4.2 Replacing the capacitor ..................................................................................................................... 5

4.3 Replacing the impeller....................................................................................................................... 5

4.4 Replacing the supply cable or float switch......................................................................................... 6

4.5 Fitting the motor................................................................................................................................. 6

5. Winding resistances........................................................................................................................ 7

6. Drawing............................................................................................................................................. 8

2 / 8

1. Identification

1.1 Nameplate

1.2 Type key

TM03 1001 0905

Pos. Description Pos. Description

1 Pump type 8 Maximum flow rate

2 Frequency 9 Motor insulation class

3 Maximum head 10 Enclosure class

4 Maximum liquid temperature during continuous operation 11 Approvals

5 Product number 12 Motor input power

6 Production code 13 Maximum installation depth

7 Full-load current 14 Supply voltage

Example Unilift CC 7 A1

Pump range

Type

Maximum head [m]

Operation

A1 = Automatic

M1 = Manual

Type

1x 220 - 240 V~40 °C

PC 0540

P171XXXX

Class I

1/1

3,7 A

Model

780 W

f50 Hz

UniliftCC9 -A1

96280970 H

max

m/h

10 m

max

UDIN EN12050-2

LGA

SN XXXXXXX

Made in Italy PC 0540

294

3 / 8

2. Fault finding

Switch off the electricity supply before dismantling the pump.

Fault Cause Remedy

1. Pump does not

run. a) Electricity supply switched off. Switch on the electricity supply.

b) Fuses in installation blown. Replace defective fuses.

c) The pump thermal switch has tripped out. The thermal switch restarts the pump when the motor has

cooled to normal temperature.

d) The main winding is defective, see 5. Winding resist-

ances. Replace the motor, see 4.1 Removing the motor.

2. The pump does

not run, but hums. a) The capacitor is defective. Replace the capacitor, see 4.2 Replacing the capacitor.

Replace the motor, 4.1 Removing the motor.

b) The auxiliary winding is defective.

3. The pump stops

after short time of

operation (ther-

mal switch tripped

out).

a) The pumped liquid temperature is too high. The pump restarts automatically after sufficient cooling.

b) Pump partly blocked by impurities or blocked. Clean the pump, see 3.2 Cleaning the impeller.

c) Water level too low when the pump is started. The

pump cannot self-prime. Move the pump to a position with higher water level or add

water until the pump starts sucking.

4. Pump runs but

gives insufficient

water.

a) Pump is partly blocked by impurities. Clean the pump, see 3.2 Cleaning the impeller.

b) Discharge pipe/hose partly blocked by impurities. The

hose may be sharply bent. Check and clean the non-return valve, if fitted.

c) Impeller, bottom part or diaphragm defective. Replace defective parts.

5. Pump runs but

gives no water. a) Pump is blocked by impurities. Clean the pump, see 3.2 Cleaning the impeller.

b) Non-return valve in discharge pipe/hose blocked in

closed position or blocked by impurities. The hose may

be sharply bent.

Check the non-return valve. Clean or replace the valve, if

necessary.

c) Pumps with float switch:

The pump does not stop because the free cable length

of the float switch is too long.

Reduce the free cable length.

4 / 8

3. Cleaning the pump

3.1 Cleaning the suction strainer

1. Drain the pump.

2. Loosen the strainer (pos. 84) by inserting a screwdriver between the bottom part (pos. 50) and the suction strainer

and turning the screwdriver.

Fig. 1. Removing the suction strainer

3. Clean and refit the suction strainer.

3.2 Cleaning the impeller

1. Loosen the strainer (pos. 84) by inserting a screwdriver between the bottom part (pos. 50) and the suction strainer

and turning the screwdriver.

2. Remove the screws (pos. 84b) and the bottom part (pos. 50).

Fig. 2. Removing the bottom part

3. Remove and clean the O-ring (pos. 37a) and the diaphragm (pos. 58).

4. Flush the inside of the pump between the motor and pump sleeve, and clean the impeller. Check that the impeller

(pos. 49) can rotate freely and is intact.

5. Fit the diaphragm, O-ring and bottom part.

6. Fit and tighten the screws.

7. Press the suction strainer onto the pump.

Switch off the electricity supply before dismantling the pump.

TM03 0831 0505

TM03 1112 1005

5 / 8

4. Dismantling and assembly

General information

Position numbers of pump part (figures) refer to exploded views, sectional drawings and parts lists.

Before dismantling

• Disconnect the electricity supply to the motor.

• Remove the electric cable in accordance with local regulations.

Before assembly

O-rings should always be replaced when the pump is overhauled.

• Clean and check all parts.

• Order the necessary service kits.

Replace defective parts by new parts.

Disposal

This product or parts of it must be disposed of in an environmentally sound way:

1. Use the public or private waste collection service.

2. If this is not possible, contact the nearest Grundfos company or service workshop.

4.1 Removing the motor

1. Loosen the strainer (pos. 84) by inserting a screwdriver between the bottom part (pos. 50) and the suction strainer

and turning the screwdriver.

2. Remove the screws (pos. 84b) and the bottom part (pos. 50).

Fig. 3. Removing the bottom part

3. Remove the O-ring (pos. 37a) and the diaphragm (pos. 58).

4. Remove the screws (pos. 36).

5. Remove the pump sleeve (pos. 55a) by holding the sleeve and pressing the impeller.

6. Moisten the O-rings (pos. 37 and 48a) and remove them.

7. Pull the motor (pos. 48) out of motor sleeve (pos. 55).

4.2 Replacing the capacitor

1. Remove the motor, see 4.1 Removing the motor.

2. Pull the capacitor (pos. 161) out of the retainer (pos. 160).

3. Pull of the cable terminals and fit the new capacitor.

4. Fit the motor, see 4.5 Fitting the motor.

4.3 Replacing the impeller

1. Remove the motor, see 4.1 Removing the motor.

2. Remove the retainer (pos. 160) with capacitor so that the shaft end is visible.

3. Insert a screwdriver into the slot in the shaft end and remove the impeller (pos. 49), nut (pos. 67) and washer (pos.

66) as well as the V-ring (pos. 159) in CC7 and CC9.

4. Keep the screwdriver in the slot and fit the washer, V-ring, if any, the new impeller and the nut.

5. Make sure that the nut is positioned in the "seat" of the impeller.

6. Fit the retainer (pos. 160) with capacitor.

7. Fit the motor, see 4.5 Fitting the motor.

TM03 1112 1005

6 / 8

4.4 Replacing the supply cable or float switch

1. Remove the motor, see 4.1 Removing the motor.

2. Cut the defective cable and the cable entry just above the motor sleeve (pos. 55).

3. Cut off the wire connectors.

4. Pull the cable and cable relief (pos. 250a) out of the motor sleeve from the inside.

5. Push the cable entry out of the motor sleeve (pos. 55) from outside and in.

6. Lead the cable through the motor sleeve, and moisten the cable entry with water and fit it with the thin end

upwards. The cable entry must be approx. 20 cm from the cable end.

Note: The cable entry for H05 cable is red, that for H07 white.

7. Fit the cable relief (pos. 250a) and pull the cable entry into position in the motor sleeve. The cable entry must now

be fixed in the retainer in the motor sleeve. It must not be possible to pull the cable any longer. The cable entry is

fitted correctly when its collar is free of the motor sleeve.

8. Strip the cable and fit the conductors with new wire connectors, see Fig. 4. Wiring diagram.

9. Fit the motor, see 4.5 Fitting the motor.

4.5 Fitting the motor

1. Fit the O-ring (pos. 48a) on the motor and place the motor in the motor sleeve (pos. 55).

2. Fit the O-ring (pos. 37) on the pump sleeve (pos. 55a).

3. Fit the pump sleeve on the motor sleeve.

4. Fit and tighten the three screws (pos. 36).

5. Fit the diaphragm (pos. 58).

6. Fit the O-ring (pos. 37) on the bottom part (pos. 50).

7. Fit the bottom part to the pump sleeve.

8. Fit and tighten the three screws (pos. 84b).

9. Fit the strainer (pos. 84).

7 / 8

5. Winding resistances

By measuring on the mains plug the resistance in the mains winding and the cable is measured.

The float switch must point upwards during the measurement.

Fig. 4. Wiring diagram

Pump type Winding resistancea±10%

a. The table values do not include the cable.

Resistance in cable: 2 x 10 m, approx. 1 Ω

Auxiliary winding Main winding

Unilift CC 5 99 Ω43 Ω

Unilift CC 7 43 Ω31 Ω

Unilift CC 9 31 Ω11 Ω

TM03 1381 1905

Red White

Black

Red

Yellow/green

Float switch

Supply

Blue

Brown

8 / 8

6. Drawing

TM03 1101 1005

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Grundfos Wasserpumpe Handbücher

Grundfos

Grundfos MAGNA1 D Bedienungsanleitung

Grundfos

Grundfos DMX 226 Bedienungsanleitung

Grundfos

Grundfos JP05S Bedienungsanleitung

Grundfos

Grundfos TPE2 D Bedienungsanleitung

Grundfos

Grundfos ALPHA1 B Bedienungsanleitung

Grundfos

Grundfos CR Series Bedienungsanleitung

Grundfos

Grundfos DMH 25X Bedienungsanleitung

Grundfos

Grundfos SPO Bedienungsanleitung

Grundfos

Grundfos PS.R.05 Bedienungsanleitung

Grundfos

Grundfos EZ Boost 15 BMQE Series Bedienungsanleitung

Grundfos

Grundfos UPSD UPN Bedienungsanleitung

Grundfos

Grundfos alpha2 l Bedienungsanleitung

Grundfos

Grundfos CRIE Bedienungsanleitung

Grundfos

Grundfos MAGNA1 C Series Bedienungsanleitung

Grundfos

Grundfos SP Series Bedienungsanleitung

Grundfos

Grundfos LS 500-300-490E Bedienungsanleitung

Grundfos

Grundfos UPM3 Bedienungsanleitung

Grundfos

Grundfos Unilift KP 250 Bedienungsanleitung

Grundfos

Grundfos MQ 3-35 Betriebsanleitung

Grundfos

Grundfos KPC 600A Bedienungsanleitung

Grundfos

Grundfos BME Bedienungsanleitung

Grundfos

Grundfos Conlift1 LS Bedienungsanleitung

Grundfos

Grundfos SLV Series Bedienungsanleitung

Grundfos

Grundfos rmq-a Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung