Grundig Reason GCT-K2305B Bedienungsanleitung

GCT-K%.182.1.18.07.2016

Owner's Manual

HD Video Cameras

GCT-K2305B 2 Megapixel Full HD-TVI Box Camera ICR

WDR

Content:

1. Important Safety Instructions 1

2. Package Contents 2

3. Rear View 2

4. Installation 3

1. Lens Mounting 3

5. Control Stick 3

6. OSD Menu 4

1. LENS 4

2. EXPOSURE 5

3. WHITE BAL (White Balance) 5

4. BACKLIGHT 6

5. DNR (Digital Noise Reduction) 7

6. DAY/NIGHT 8

7. IMAGE 9

8. MOTION 11

9. SYSTEM 11

10. EXIT 12

1. Important Safety Instructions

Be sure to use only the standard adapter that is specified in the specification sheet.

Using any other adapter could cause fire, electrical shock, or damage to the product.

Incorrectly connecting the power supply may cause explosion, fire, electric shock, or

damage to the product. Do not connect multiple products to one single adapter.

Exceeding the capacity may cause abnormal heat generation or fire.

Do not place conductive objects (e.g. screwdrivers, coins or any metal items) or

containers filled with water on top of the product. Doing so may cause personal injury

due to fire, electric shock, or falling objects.

English

If any unusual smells or smoke comes out of the unit, stop using the product. In this

case, immediately disconnect the power source and contact the service center.

Continued use in such a condition may cause fire or electric shock.

If this product fails to operate normally, contact the nearest service center. Never

disassemble or modify this product in any way. (GRUNDIG is not liable for problems

caused by unauthorised modifications or attempted repair.)

To prevent fire or electric shock, do not expose the inside of this device to rain or

moisture.

2. Package Contents

These parts are included:

3. Rear View

2English

4. Installation

Do not install this product in a location subject to high temperature (over 55°C), low

temperature (below -25°C), or high humidity. Doing so may cause fire or electric shock.

Keep out of direct sunlight and heat radiation sources. This may cause fire.

Do not install the unit in humid, dusty or sooty locations. Doing so may cause fire or

electric shock. Install it in a place with good ventilation.

When installing the unit, fasten it securely and firmly. A falling unit may cause personal

injury.

If you want to relocate the already installed product, be sure to turn the power off and

then move or reinstall it.

4.1. Lens Mounting

Lens Mounting for C/CS Mount Lens Model:

It is possible to attach all CS-Mount lenses with manual or DC controlled iris on the

camera. Please remove the camera’s plastic covering first and then attach the CS-Mount

lens onto the camera. If you would like to use a C-Mount lens, you need a 5 mm C/CS

Mount Adapter between the camera and the C-Mount lens, as shown in the illustration

below.

5. Control Stick

- Pressing the SET UP stick: Accesses the menu mode or confirms the setting.

- UP / DOWN: Chooses the desired menu.

- LEFT / RIGHT: Sets up the value of the selected menu and changes the settings.

English

6. OSD Menu

1. Press the SET UP stick to access the menu mode.

2. Select the desired feature by using UP/DOWN.

3. If there is a setting for this feature on the right side of the screen, use LEFT/RIGHT to

switch between the settings and confirm your choice by pressing the stick. If an ENTER

arrow (↵) is displayed, press the stick to access the according submenu.

4. In the sub-menus, please press with the stick on RETURN to return to the previous

menu.

5. To exit the menu, please press the stick on EXIT in the main menu.

When you press the SET UP stick for the first time, the MENU page will be displayed on

the monitor.

LENS: You can choose between Indoor or

Outdoor mode.

EXPOSURE: This function is used to

control the light exposure.

WHITE BAL: You can control the white

balance under different lighting conditions

here.

BACKLIGHT: You can control the backlight

compensation here.

DNR: This noise reduction function is to decrease the noise which can be generated

under low light conditions.

DAY&NIGHT: This function is used to improve the camera's sensitivity at night or when

the brightness level of the ambient environment is low.

IMAGE: You can set different picture related settings like mirroring, sharpness, hue and

gain.

MOTION: This function is used to detect moving objects in the monitoring area.

SYSTEM: Configures camera related functions and data.

EXIT: Here you can exit the menu.

6.1. LENS

Here you can configure the lens setting.

LENS [DC, MANUAL] :

If you are using a lens with manual Iris, set this item to MANUAL. If you are using a DC

controlled lens, set it to DC.

4English

- DC [INDOOR, OUTDOOR, DEBLUR]: You can select a mode depending on the

installation environment.

- MANUAL [NORMAL, DEBLUR]: You can select a mode depending on the installation

environment.

6.2. EXPOSURE

This function is used to control the light exposure.

BRIGHTNESS [0~20] :

Sets the value of auto exposure operations.

As the value increases, the screen gets

brighter.

SHUTTER [AUTO, MANUAL, FLICKER] :

Adjust the electronic shutter speed by selecting one of the modes. If you select

MANUAL, the following sub-menu will appear.

- SPEED [for 25 fps: 1/25~1/30,000 / for 30

fps: 1/30~1/30,000]: Control the image

brightness by adjusting the shutter speed.

SENS-UP [x2~x32] :

This feature ensures clear images at night or under low light conditions.

AGC [0~20] :

This function is used to create brighter images. As the AGC value increases, the overall

screen gets brighter but the level of noise is also increasing.

6.3. WHITE BAL (White Balance)

This function is used to control the white balance under different lighting conditions.

Adjusting the setting calibrates the camera for correct and natural colour rendering.

English

WHITE BAL [ATW, AWB, AWC→SET, MANUAL] :

- ATW: Select this mode when the colour temperature is between 1,800˚K and 10,500˚K.

- AWB: This function is used to search for colours that match the ambient environment

well. Select this mode when the colour temperature is between 3,000˚K and 7,000˚K.

- AWC→SET: To find the optimal luminance level for the current environment, point the

camera towards a sheet of white paper and press the SET UP stick. If the environment

changes, re-adjust this setting.

- MANUAL: Select this option to fine-tune

the White Balance manually. Set the White

Balance first by using the ATW or the AWC

mode. After that switch to MANUAL mode

and press the SET UP stick. Fine-tune the

White Balance (KELVIN) and change the

BLUE and RED values to meet the best

result.

NOTE:

The White Balance may not work properly under the following conditions. If that is the

case, select the ATW or AWB mode (automatic mode).

1. When the colour temperature of the environment surrounding the subject is out of the

control range (e.g. clear sky or sunset).

2. When the ambient illumination of the subject is dim.

3. When the camera is directed towards a fluorescent light or is installed in a place

where the illumination changes dramatically, the White Balance operation may become

unstable.

6.4. BACKLIGHT

To overcome difficult light situations, this GRUNDIG camera features different options to

improve the image quality. You can choose between HLC, BLC, WDR, OFF.

This function is used for backlight compensation. Please choose from OFF, WDR, BLC

and HLC.

OFF: Deactivated.

6English

HLC (High Light Compensation):

This function is used to surpress or mask a

strong light source (for example, headlights

of cars during night-time) so that other

subjects can be seen in more detail.

- LEVEL: Adjust the brightness level from

which on the light source is to be masked

out.

- MODE: Choose the mode.

BLC (Back Light Compensation):

This function is used to counterbalance the

screen image by increasing the brightness

so that a subject which appears dark due to

a strong backlight can be displayed in more

detail. If you select BLC, a submenu

appears where you can make finer

adjustments.

- H-POS/ V-POS/ H-SIZE/ V-SIZE: Define

the position and size of the area of interest

by changing the position & size.

WDR:

The WDR (Wide Dynamic Range) function

works to correct excessive light within the

frame to produce a usable image. When the

image has simultaneous bright and dark

areas, it makes both areas distinct. If you

select WDR, a submenu appears where you

can make finer adjustments.

- WEIGHT [MIDDLE, HIGH, LOW]: Select

the WDR level of the camera.

NOTE: The WDR function might lead to a reduced framerate and “ghost” effects in areas

with very bright background.

6.5. DNR (Digital Noise Reduction)

This function is used to improve the picture quality by filtering the noise which is

generated under low bright light conditions. You can set 3 different levels [LOW,

MIDDLE, HIGH] here.

DNR [OFF, LOW, MIDDLE, HIGH] :

Using DNR (Digital Noise Reduction), you can control the noise on the screen. This is

especially useful when the image is very noisy due to low light.

English

NOTE: If the DNR function is used, the cancellation of the noise will be excellent. The

higher the compensation proportion is raised, the better the effect of noise cancellation

will be, but a ghost effect may also occur.

6.6. DAY/NIGHT

This function is used to improve the camera's sensitivity at night or when the brigthness

level of the ambient environment is low.

DAY & NIGHT [AUTO, COLOR, B/W, EXTERN] :

- EXTERN: The Day and Night function will be adjusted by the built-in Light Sensor.

> SMART IR [0~20] : This option controls

the IR LED (bright portion base), saturation

is not expected.

> EXTERN S / W [HIGH, LOW]: Set the

setting of the external Switch to HIGH or

LOW.

> DELAY [LOW, MIDDLE, HIGH]: Set the

working time of the D/N filter.

- AUTO: This mode switches to ‘Colour’ in a

normal environment, but switches to ‘B/W’

mode when the ambient illumination is low.

To set up the switching time for AUTO

mode, press the SET UP stick. In B/W

mode, you can turn the BURST signal ON

or OFF.

> SMART IR [0~20]: This option controls the IR LED (bright portion base), saturation is

not expected.

> AGC THRES [0-20]: Execute the Day/Night switch depending on the AGC level that is

used to increase the brightness of the image. Higher values require a darker illumination

to execute the switch.

> AGC MARGIN [0-20]: Define the difference between the Day/Night & Night/Day switch

based on AGC THRES. Higher values will increase this distance and can help to prevent

continuous switching between Day & Night mode.

> DELAY [LOW, MIDDLE, HIGH]: Set the working time of the D/N filter.

- COLOR: The picture will be always displayed in colour.

- B / W: The picture will be always displayed in black & white. In B/W mode, you can turn

the BURST signal ON or OFF.

8English

Inhaltsverzeichnis

Andere Grundig IP-Kamera Handbücher

Grundig

Grundig GCI-C0735P Bedienungsanleitung

Grundig

Grundig GCI-K1503B(S) Bedienungsanleitung

Grundig

Grundig GCI-K1677D Bedienungsanleitung

Grundig

Grundig GCI-M1566F Bedienungsanleitung

Grundig

Grundig GCI-F1576V Bedienungsanleitung

Grundig

Grundig GCH-K0305B Bedienungsanleitung

Grundig

Grundig GCI-K0622D Bedienungsanleitung

Grundig

Grundig GCA-B0323T Bedienungsanleitung

Grundig

Grundig GD-CI-BP2647P Bedienungsanleitung

Grundig

Grundig GCH-K1327T-1 Bedienungsanleitung

Grundig

Grundig GCT-K2326D Bedienungsanleitung

Grundig

Grundig GCI-H0503B Bedienungsanleitung

Grundig

Grundig GCI-K1587V Bedienungsanleitung

Grundig

Grundig GCI-K0779P Bedienungsanleitung

Grundig

Grundig GCI-K1503B Bedienungsanleitung

Grundig

Grundig GCI-K1527V-1 Bedienungsanleitung

Grundig

Grundig GCI-K1527V Bedienungsanleitung

Grundig

Grundig GCI-K1577TH Bedienungsanleitung

Grundig

Grundig GCT-K0123T Bedienungsanleitung

Grundig

Grundig G-BCAM-01 Bedienungsanleitung

Grundig

Grundig GCI-K1627D Bedienungsanleitung

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung