Guardian 900-1086 Bedienungsanleitung

Installation

Instruction

Manual

Guardian® Easytrack System

Wall Mount Assembly

Model 900-1086

All manuals and user guides at all-guides.com

all-guides.com

Wall Mount Assembly

2Introduction

TABLE OF CONTENTS

Introduction .......................................................................................... 2

Important Safeguards.............................................................................. 3

Requirements ......................................................................................... 4

Before ou Begin .................................................................................... 4

Kit Contents & Part Numbers .................................................................... 5

Assembly of Wall Mount Assembly ............................................................. 5

Maintenance .......................................................................................... 6

Warranty ............................................................................................... 7

This manual contains important safety and maintenance instructions. Please read

it carefully before usin your Easytrack System and refer to it as often as needed

for safe and efficient use.

If you have questions regarding the safe use and/or assembly, maintenance or specifications of your

Easytrack System, you should call Customer Service at 800-333-4000, 303-218-4600 or from Canada at

800-263-3390.

For service and repair, remember your authorized Sunrise supplier is able to provide the assistance you

need.

Save this manual for future reference.

SUNRISE LISTENS

Thank you for choosing a Guardian Easytrack System. We want to hear your questions or

comments about this manual, the safety and reliability of your Easytrack System and the

service you receive from your Sunrise Medical Supplier. Please feel free to write or call us at

the address and telephone number below:

Sunrise Medical

Customer Service Department

7477 East Dry Creek Parkway

Longmont, Colorado 80503

(303) 218-4600 or (800) 333-4000

FOR ANSWERS TO YOUR QUESTIONS

our authorized supplier knows your Easytrack System best and can answer most of your

questions about its safety, use and maintenance. For future reference, fill in the following:

Supplier: ___________________________________________________________________

Address: ____________________________________________________________________

Telephone: __________________________________________________________________

Serial #: ____________________________________________________________________

Date Purchased: _____________________________________________________________

All manuals and user guides at all-guides.com

Wall Mount Assembly

IMPORTANT SAFEGUARDS

Do not operate this equipment without first readin and understandin this manual.

Should you be unable to understand the warnin s, cautions and instructions,

contact our technical support or your local dealer before attemptin to use this

equipment– otherwise injury or dama e may result.

Important information is highlighted by these terms:

WARNING– Notices as used in the manual apply to hazards or unsafe practices which

could result in serious bodily harm.

CAUTION– Notices as used in this manual apply to hazards or unsafe practices, which

could result in minor personal injury or property damage.

NOTES– Highlight procedures and contain information which assist the operator in

understanding the information contained in this manual.

NOTE– The information contained in this document is subject to change without notice.

SAVE THESE INSTRUCTIONS AND KEEP WITH EASYTRACK AT ALL TIMES.

The Easytrack System and its accessories are intended to be used as an assistive

device for transferrin a person between the posts. The Easytrack system is only

to be used with the Guardian Voya er Portable lift.

USE ONLY AS INTENDED - This product may cause serious injury if not installed and

operated accordin to the instruction manual.

Failure to observe warnings listed below could result in serious injury.

This instruction manual is for the installation of the Easytrack Wall Mount only. For more

information about the Easytrack system, please refer to the Easytrack user manual.

Before you Install the Easytrack Wall Mount

• If you are unsure of the strength or stability of your wall, do not install the wall

mount; consult you local supplier.

• Do not install on a wall with water damage.

• Do not drop product; may cause breakage.

• Do not completely submerge in water.

• Do not attempt to over-extend the rail past the locking point.

When the Easytrack is in Use

• Do not use the Easytrack system as a swing.

• Refrain from swinging patient sideways of rail.

Important Safeguards 3

All manuals and user guides at all-guides.com

ASSEMBLY INSTRUCTIONS

REQUIREMENTS

Failure to meet requirements listed below could result in serious bodily harm.

• Wall mount should be installed by a skilled tradesperson. Installation of the wall

mount by someone unskilled will void Sunrise warranty and may cause serious injury

or damage.

• Every month a maintenance check should be done to ensure the rail is level (see

“Maintenance” in this manual).

• Protect the Easytrack System and its accessories during transport.

•Wall Requirements:

WOOD STRUCTURE – minimum 2” X 3” Studs

CONCRETE STRUCTURE

• Do no install if wall does not meet requirements.

• Do not install on a wall with a steel structure.

BEFORE YOU BEGIN

Read “Requirements” and “Important Safe uards” before attemptin to assemble

the Easytrack System.

1. Survey the room where you plan to install the Easytrack Wall Mount. Make sure the

room meets all the specifications outlined in “Requirements”.

2. Use the measurements below to determine the best place to put the Easytrack System:

a. Over a bed – approx. 36-40” (915-1020 mm) from the head of the bed (Fi ure 1).

b. Over a tub – approx. 16-18” (400-460 mm) from the end of the tub (Fi ure 1).

c. Allow 36” (915 mm) of open area for transfer working space (Fi ure 2).

d. Allow a minimum of 53” (1340 mm) from the bottom of the rail to the top of any

object to be transferred over (Fi ure 3).

3. Transfers should only take place under the Easytrack rail (Fi ures 4 & 5).

4. The Wall Mount may be installed on either a concrete wall or wood-framed wall. For

wood, the wall mount must be attached to a minimum of three (3) 2" X 3" studs. DO

NOT attempt to install the wall mount on less than 3 studs (Fi ure 6).

5. Wall Mount must be positioned on the wall to ensure the angle between the wall and

the rail will be more than 30° (Fi ure 7).

Wall Mount Assembly

4Assembly Instructions

studs

wall mount plate

30° 30°

Maximum angle

36-40"

(915-1020mm)

53"

(1340mm)

80.2-130"

(2040-3300mm)

84.8-134.5"

(2155-3415mm)

20"

(510mm)

84-108"

(2130-2745mm)

16-18"

(400-460mm)

All manuals and user guides at all-guides.com

Wall Mount Assembly

EASYTRACK WALL MOUNT KIT

CONTENTS & PART NUMBERS (Fi ure 8)

Description Part # Qty

1 Wall mount plate 900-1085 1

2 Pivoting rail

attachment 900-1087 1

Includes:

3 Round blue cap 900-1072 1

4 Pivot wall mount N/A 1

5 Fixation wall mount N/A 1

6 Back plate N/A 1

7 M 10 X025 screw 900-0409 1

ASSEMBLY OF WALL MOUNT ASSEMBLY

Tools required:

• Step ladder

• Tape measure

• 6 concrete 3/8” anchors or 6 3/8” lag bolts

• Drill

• Wrench with a 9/16” socket

• Someone to assist you

• Stud finder

1. Refer to Fi ures 9A and 9B for the distance required between the ceiling and where

the top of the wall mount must be installed. Please note that when the wall bracket

will have the pivoting rail of a 3 post system attached, the mounting point must be

lower than with a standard rail.

2. Insert the pivoting rail attachment into the wall plate. Refer to Fi ure 10 to insure

that the bracket is placed properly.

3. Install the wall plate on the wall. The wall plate must be installed on a concrete wall

with six (6) 3/8 in. concrete anchors or on three (3) 2x3 (minimum size) wooded studs

with two (2) 3/8" diameter (M10), 4 in. long lag bolts on each stud (Fi ure 11).

Wood studs– Use a stud finder to find the center of each stud. It is necessary to pre-

drill holes into each stud before screwing the lag bolt to prevent the wood from

cracking.

NOTE– Make sure the rail is level before securing wall mount to wall.

Follow drill size recommendation for lag bolt:

LAG BOLT M10 3/8 "

PRE-DRILL SIZE 6.5 mm 1/4 "

Pre-drilled holes must be in the center of the stud. If holes are not properly

centered, serious dama e or injury may occur.

DO NOT install into steel stud, reinforcement may be required.

CAUTION– Avoid drilling close to any electrical wiring or plumbing. Please, make sure you know what

is behind the wall you are drilling in before doing any modifications to it. Failure to do so

may cause serious injury.

4. See “Before you start” for suggested position. Slide the pivoting rail attachment into its

final position. For the 3 post assembly, the bracket must be placed in a way that the rail

won’t, when turning, generate an angle beyond the maximum allowed (Fi ure 12).

5. Tighten the four bolts on pivoting rail attachment. The rail can now be attached to

wall mount.

Assembly Instructions 5

standard rail

pivoting rail

ceiling

bottom

30° 30°

Maximum angle

1 1/8"

(28mm)

5 1/4"

(133mm)

All manuals and user guides at all-guides.com

MAINTENANCE

Failure to follow maintenance instructions below when indicated could result in

injury or dama e.

Periodic inspection should be performed by a person who is suitably and properly qualified

and well acquainted with the design, use and care of the Easytrack System. Contact your

local dealer/distributor.

Inspection should be carried out both routinely (at least as often as specified) and, as nec-

essary. If any damage to the system is detected through routine inspections, do not use

the system and immediately contact your supplier.

Upon receipt of your Easytrack Wall Bracket:

1. Make sure you received all components listed in Fi ure 8.

2. Inspect all parts for possible damage in transit.

3. Ensure all components are in working order.

4. Repair/replacement of any faulty parts.

5. Keep a log of any repair/replacement required.

Before each time you use the Easytrack Wall Bracket:

1. Clean the outside and inside of the rail and wipe out any water in the rail. Failure to

do so for a long period of time can cause corrosion that will weaken the rail.

2. Check that the rail is secure in place. Press the rail upwards to make sure that the

rail is locked onto the post.

3. Check if there is any appearance of damage. If there is any appearance of damage,

do not use the Easytrack System.

Every month:

1. Clean inside of rail with a damp cloth to ensure there is no dust or grease build-up

inside of rail.

2. Check to ensure you still have all your original parts. If any parts are missing they

should be replaced before using the Easytrack Wall Bracket again.

3. Check for the appearance of rust. If rust is starting to appear, simply scrub the piece

clean.

4. Examine all joints and pieces for wear and fatigue. Replace any part that looks dam-

aged or worn. Document inspection and any repairs.

Follow uidelines in your portable lift manual for maintenance and procedures on

the lift.

Wall Mount Assembly

6Maintenance

All manuals and user guides at all-guides.com

all-guides.com

Wall Mount Assembly

WARRANTY

This warranty is extended only to the original purchaser/user of Sunrise products.

Sunrise Medical Inc. warrants its products to be free from defects in material under normal

use and service and will, within the periods stated below, from the date of purchase. If

within such warranty period any such product shall be proven to be defective, such product

shall be repaired or replaced at Sunrise Medical's option. This warranty does not include

any labor or shipping charges incurred in replacement part installation or repair of any such

product. Sunrise Medical's sole obligation and your exclusive remedy under this warranty

shall be limited to such repair and/or replacement.

Lifter including hydraulics 1 year

Accessories on Lifter 1 year

Slings 1 year

Batteries 3 months

Easytrack System 1 year

For warranty service, please contact the provider from whom you purchased the Sunrise

Medical product. In the event that you do not receive satisfactory warranty service, please

contact Sunrise Medical customer service at 1-800-333-4000.

Do not return products to our factory without prior authorization. Sunrise Medical will issue

a Return Merchandise Authorization (RMA) Number. C.O.D. shipments will be refused; all

shipments to Sunrise Medical must be prepaid. For this warranty to be valid, the purchaser

must present its original proof of purchase at the moment of the claim. The defective unit,

assembly or part must be returned to Sunrise Medical for inspection. The part or compo-

nents repaired or replaced are guaranteed for the remaining period of the initial warranty.

Limitations and Exclusions:

The above warranty does not apply to serial numbered products if the serial number has

been removed or defaced.

No warranty claim shall apply where the product or any other part thereof has been altered,

varied, modified, or damaged; either accidentally or through improper or negligent use and

storage. Warranty does not apply to products modified without Sunrise Medical's express

written consent, (including but not limited to products modified with unauthorized parts or

attachments); products damaged by reason of repairs made to any component without the

specific consent of Sunrise Medical, or to products damaged by circumstances beyond

Sunrise Medical's control. Evaluation of warranty claim will be solely determined by Sunrise

Medical. The warranty does not apply to problems arising from normal wear or failure to

adhere to the instructions in this manual. Sunrise Medical Inc. slings are void of warranty

if not laundered as per instructions on the Sling Label.

Sunrise Medical Inc. shall not be liable for damages losses or inconveniences caused by a

carrier.

This warranty replaces any other warranty expressed or implicit and constitutes Sunrise

Medical Inc.'s only obligation towards the purchaser. Sunrise Medical shall not be liable for

any consequential or incidental damages whatsoever.

Warranty 7

All manuals and user guides at all-guides.com

Manufactured for:

Sunrise Medical

7477 East Dry Creek Parkway

Longmont, Colorado 80503

(800) 333-4000

In Canada (800) 263-3390

Printed in Canada

900-0690 Rev. A

All manuals and user guides at all-guides.com

Inhaltsverzeichnis

Andere Guardian Rack & Stand Handbücher

Guardian

Guardian Floor Stand IC-7714 Bedienerhandbuch

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung