Guildline 7810 Bedienungsanleitung

OPERATOR MANUAL

For The

Model 7810

Transconductance Amplifier

www.guildline.com

NOTICE

The contents and information contained in this manual are proprietary to

Guildline Instruments Limited. They are to be used only as a guide to the

operation and maintenance of the equipmentwith which this manual was issued

and may not be duplicated or transmitted by any means, either in whole or in

part, without the written permission of Guildline Instruments Limited.

OM7810-8-00

25 August, 2023

OM7810-8-00

25 August, 2023

TABLE OF CONTENTS

1. INTRODUCTION.......................................................................................................1-1

1.1. SCOPE................................................................................................................................................................1-1

1.2. GENERAL DESCRIPTION............................................................................................................................1-1

1.3. WARRANTY.....................................................................................................................................................1-2

1.4. TO OBTAIN WARRANTY SERVICE .........................................................................................................1-2

1.5. SPECIFICATIONS...........................................................................................................................................1-4

1.5.1. Output Current Ranges...................................................................................................................................1-4

1.5.2. Stability Over 10 Minute Interval..................................................................................................................1-4

1.5.3. Accuracy Over 1 Year, 95 % Uncertainty.....................................................................................................1-5

1.5.4. General Specifications....................................................................................................................................1-6

2. INSTALLATION........................................................................................................2-1

2.1. INITIAL INSPECTION...................................................................................................................................2-1

2.2. POWER REQUIREMENTS...........................................................................................................................2-1

2.3. PRELIMINARY SETUP POCEDURE .........................................................................................................2-1

2.4. WARNING: .......................................................................................................................................................2-2

3. MANUAL OPERATION ............................................................................................3-1

3.1. FRONT PANEL................................................................................................................................................3-1

3.1.1. Touch Screen..................................................................................................................................................3-1

3.1.2. USB Interface Bus..........................................................................................................................................3-1

3.1.3. Input................................................................................................................................................................3-2

3.1.6. Guard ..............................................................................................................................................................3-3

3.2. REAR PANEL...................................................................................................................................................3-4

3.2.1. Power Entry....................................................................................................................................................3-4

3.2.2. GPIB Interface Bus ........................................................................................................................................3-4

3.2.3. USB Interface Bus..........................................................................................................................................3-5

3.3. FRONT PANEL TOUCH SCREEN OPERATION.....................................................................................3-5

3.4. MAIN SCREEN ................................................................................................................................................3-6

3.5. SETUP SCREEN...............................................................................................................................................3-8

3.8.1. Link To Common.........................................................................................................................................3-11

3.8.2. Circuit Common Connection To Output.....................................................................................................3-11

3.8.3. Input and Output Guard Strategy.................................................................................................................3-11

OM7810-8-00

25 August, 2023

4. THEORY OF OPERATION.......................................................................................4-1

4.1. INTRODUCTION.............................................................................................................................................4-1

4.2. OVERVIEW ......................................................................................................................................................4-1

4.3. INSTRUMENT CONTROL............................................................................................................................4-1

4.4. VOLTAGE INPUT CIRCUIT ........................................................................................................................4-2

4.5. COMPLIANCE VOLTAGE DISPLAY ........................................................................................................4-2

4.6. SIGNAL FREQUENCY and INPUT VOLTAGE DISPLAY.....................................................................4-2

4.7. OVERLOAD DETECTION and PROTECTION........................................................................................4-2

5. MAINTENANCE AND TROUBLESHOOTING.........................................................5-1

5.1. PERIODIC MAINTENANCE.........................................................................................................................5-1

5.2. TROUBLESHOOTING...................................................................................................................................5-1

5.3. PERFORMANCE VERIFICATION AND CALIBRATION.....................................................................5-2

5.3.1. Test Equipment Required...............................................................................................................................5-2

5.3.2. DC Accuracy And Stability Verification and Calibration.............................................................................5-2

5.3.3. Procedural Steps For DC Current Verification..............................................................................................5-3

5.3.4. Procedural Steps For AC Current Verification..............................................................................................5-6

6. REMOTE CONTROL................................................................................................6-1

6.1. INTERFACES...................................................................................................................................................6-1

6.2. IEEE-488 (GPIB) INTERFACE .....................................................................................................................6-1

6.2.1. Controller........................................................................................................................................................6-2

6.2.2. IEEE-488 Responses......................................................................................................................................6-2

6.2.3. Interconnecting Cable And IEEE-488 Connector.........................................................................................6-2

6.2.4. Typical System...............................................................................................................................................6-2

6.2.5. Address And Talk/Listen Selection...............................................................................................................6-3

6.2.6. IEEE-488 Electrical Interface ........................................................................................................................6-3

6.2.7. IEEE-488 Input Buffering..............................................................................................................................6-5

6.2.8. IEEE-488 Output Buffering...........................................................................................................................6-5

6.2.9. IEEE-488 Deadlock........................................................................................................................................6-5

6.3. RS-232C INTERFACE.....................................................................................................................................6-5

6.3.1. RS-232C Responses.......................................................................................................................................6-6

6.4. COMMAND LANGUAGE..............................................................................................................................6-6

6.4.1. General Syntax For Commands.....................................................................................................................6-6

6.4.2. General Syntax For Numbers.........................................................................................................................6-7

OM7810-8-00

25 August, 2023

iii

6.5. REMOTE AND LOCAL OPERATION........................................................................................................6-8

6.5.1. Local...............................................................................................................................................................6-8

6.5.2. Local With Lockout .......................................................................................................................................6-8

6.5.3. Remote............................................................................................................................................................6-8

6.5.4. Remote With Lockout....................................................................................................................................6-8

6.6. PROGRAMMING COMMAND SUMMARY .............................................................................................6-9

6.7. REMOTE COMMANDS...............................................................................................................................6-11

6.7.1. *CLS - Clear Status Command....................................................................................................................6-11

6.7.2. *ESE <u> - Set Event Status Enable Register.............................................................................................6-11

6.7.3. *ESE? - Event Status Enable Query............................................................................................................6-11

6.7.4. *ESR? - Event Status Register Query..........................................................................................................6-11

6.7.5. *IDN? - Identification Query.......................................................................................................................6-13

6.7.6. *OPC - Operation Complete........................................................................................................................6-14

6.7.7. *OPC? - Operation Complete Query...........................................................................................................6-14

6.7.8. *OPT? - Report Available Options..............................................................................................................6-14

6.7.9. *RST - Device Reset....................................................................................................................................6-14

6.7.10. *SRE <u> - Service Request Enable Command ....................................................................................6-15

6.7.11. *SRE? - Service Request Enable Query.................................................................................................6-15

6.7.12. *STB? - Status Byte Query.....................................................................................................................6-15

6.7.13. *TST? - Query Results Of Self Test.......................................................................................................6-15

6.7.14. *TRG - Group Execute Trigger..............................................................................................................6-15

6.7.15. Date? - Display The 7810 Internal Date.................................................................................................6-16

6.7.16. DER? - Device Error Register ................................................................................................................6-16

6.7.17. Operate – Set The Operation State..........................................................................................................6-17

6.7.18. Operate? - Display The Current Operation State....................................................................................6-18

6.7.19. Range - Select Output Current Range.....................................................................................................6-18

6.7.20. Range? - Display The Currently Selected Range...................................................................................6-18

6.7.21. SInce? - Display The Time The 7810 Was Last Reset...........................................................................6-19

6.7.22. Serial Number - Set The 7810 Serial Number........................................................................................6-19

6.7.23. TErse - Turn Off Verbose Mode.............................................................................................................6-19

6.7.24. UPtime? - Display How Long The 7810 Has Been Running................................................................6-19

6.7.25. VErbose - Set Verbose Mode..................................................................................................................6-20

6.7.26. Volt - Select The Input Voltage Range...................................................................................................6-20

6.7.27. Volt? - Display The Current Input Voltage Range.................................................................................6-20

6.7.28. Programming Hints.................................................................................................................................6-20

OM7810-8-00

25 August, 2023

OM7810-8-00

25 August, 2023

LIST OF FIGURES

FIGURE 1-1 : MODEL 7810..........................................................................................................................................1-1

FIGURE 3-1 : FRONT PANEL GUILDLINE 7810....................................................................................................3-1

FIGURE 3-2 : INPUT TERMINALS............................................................................................................................3-2

FIGURE 3-3 : REAR PANEL GUILDLINE 7810.......................................................................................................3-4

FIGURE 4-1 : MODEL 7810 BLOCK DIAGRAM.....................................................................................................4-3

FIGURE 5-1 : VERIFICATION TEST SET-UP.........................................................................................................5-2

FIGURE 5-2: INPUT TERMINALS............................................................................................................................5-3

FIGURE 6-1 : EVENT STATUS BIT OPERATION................................................................................................6-10

OM7810-8-00

25 August, 2023

OM7810-8-00

25 August, 2023

vii

LIST OF TABLES

TABLE 2-1 : LINE CORD WIRING ............................................................................................................................2-1

TABLE 5-1 : TROUBLESHOOTING GUIDE............................................................................................................5-1

TABLE 5-2 : REFERENCE CURRENT SHUNT SELECTION..............................................................................5-3

TABLE 5-3 : POSITIVE DC VERIFICATION VALUES.........................................................................................5-5

TABLE 5-4 : NEGATIVE DC VERIFICATION VALUES.......................................................................................5-5

TABLE 5-5 : 100 KHZ AC VERIFICATION VALUES ............................................................................................5-7

TABLE 5-6 : 1 KHZ AC VERIFICATION VALUES ................................................................................................5-7

TABLE 5-7 : 10 KHZ AC VERIFICATION VALUES ..............................................................................................5-8

TABLE 5-8 : 30 KHZ AC VERIFICATION VALUES ..............................................................................................5-8

TABLE 5-9 : 100 KHZ AC VERIFICATION VALUES............................................................................................5-8

TABLE 6-1 : IEEE-488 DEVICE CAPABILITIES...................................................................................................6-3

TABLE 6-2 : IEEE-488 PIN DESIGNATIONS..........................................................................................................6-4

TABLE 6-3 : RS232 PIN DESIGNATIONS................................................................................................................6-6

TABLE 6-4 : REMOTE/LOCAL STATE TRANSITIONS .....................................................................................6-9

TABLE 6-5 : EVENT STATUS REGISTER............................................................................................................6-12

TABLE 6-6 : STATUS BYTE REGISTER...............................................................................................................6-13

TABLE 6-7 : DEVICE ERROR REGISTER ...........................................................................................................6-17

OM7810-8-00

25 August, 2023

viii

Inhaltsverzeichnis

Andere Guildline Verstärker Handbücher

Guildline

Guildline 7620 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung