H3C PSR1600B-12A-B Bedienungsanleitung

H3C PSR1600B-12A-B

Power Module

User Manual

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: APW100-20190612

its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of New H3C

Technologies Co., Ltd.

Trademarks

Except for the trademarks of New H3C Technologies Co., Ltd., any

trademarks that may be mentioned in this document are the property

of their respective owners.

Notice

The information in this document is subject to change without notice.

All contents in this document, including statements, information, and

recommendations, are believed to be accurate, but they are

presented without warranty of any kind, express or implied. H3C shall

not be liable for technical or editorial errors or omissions contained

herein.

Environmental protection

This product has been designed to comply with the environmental

protection requirements. The storage, use, and disposal of this

product must meet the applicable national laws and regulations.

Documentation feedback

You can e-mail your comments about product documentation to

[email protected].

We appreciate your comments

Contents

Overview ·················································· 1

About the power module··················································· 1

Technical specifications ··················································· 1

Views ··········································································· 2

LEDs············································································ 2

Installing and removing the power module······· 4

Safety precautions ·························································· 4

Installation tools······························································ 4

Installing the power module··············································· 4

Connecting the power cord ··············································· 6

Removing the power module············································· 8

Overview

About the power module

The PSR1600B-12A-B is an AC-input and DC-output power module.

It provides a maximum output of 1600 W.

The power module has the following features:

•Self-protection—The power module provides a self-protection

mechanism against input overcurrent, input undervoltage, output

overcurrent, output overvoltage, output short circuit, and

overtemperature conditions.

•Redundancy—The power module can work together with a

second one or more to achieve N+1 or N+N redundancy and load

sharing.

•Hot swapping—The power module can be installed on or

removed from an operating device. You can remove a power

module only when the remaining power modules can provide

sufficient power for the device.

Technical specifications

Item Specification

Rated input voltage 100 to 240 VAC @ 50 or 60 Hz

Output voltage 12 V

Maximum output current 131 A (12 V)

Maximum output power 1600 W

Dimensions (H × W × D)

(including the handle) 40.2 × 73.5 × 253.8 mm (1.58 ×

2.89 × 9.99 in)

Item Specification

Ambient temperature,

operating –10°C to +55°C (+14°F to +131°F)

Ambient humidity (RH),

noncondensing 5% to 95%

Views

Figure 1 PSR1600B-12A-B power module view

(1) Handle (2) AC-input receptacle

(3) Latch (4) Status LED

LEDs

The power module has a LED to indicate its operating status.

LED status Description

Steady green The power module is operating correctly,

and is in active state.

Flashing green at

1 Hz The power module is operating correctly,

and is in standby state.

Flashing green at

2 Hz The power module is updating the software.

Steady amber The power module is faulty or in

self-protection mode.

Flashing amber at

1 Hz

Abnormal power output. (Output

overvoltage, output undervoltage, output

overcurrent, output overpower, or

overtemperature has occurred. The power

module has not entered self-protection

mode.)

Flashing amber at

2 Hz

The power module does not have power

input but other power modules in the device

have power input.

Off No power modules in the device have

power input.

Installing and removing the power

module

Safety precautions

To avoid injuring yourself or damaging the power module and device,

follow these safety precautions:

•When installing and removing the power module, wear an ESD

wrist strap. Make sure the strap makes good skin contact and is

reliably grounded.

•To avoid damaging the power module and device, make sure

the external power source provides a voltage as required by the

power module and the power module output voltage is as

required by the device.

•To avoid bodily injury, do not touch any bare cables or terminals

of the power module.

•Do not place the power module in a wet area, and prevent liquid

from flowing into the power module.

•To avoid power module damage, do not open the power module.

When an internal circuit or component is faulty, contact H3C

Support.

Installation tools

You must wear an ESD wrist strap when installing or removing the

power module. Prepare one yourself.

Installing the power module

To avoid bodily injury or device damage, strictly follow the procedure

in Figure 2 to install the power module.

Figure 2 Power module installation procedure

To install the power module:

1. Wear an ESD wrist strap, and make sure the strap makes good

skin contact and is reliably grounded.

2. Unpack the power module. Make sure the power module model

is as required.

3. As shown in Figure 3, correctly orient the power module.

Holding the power module handle with one hand and supporting

the power module bottom with the other, align the power module

with the target power module slot. Push the power module

slowly into the slot along the guide rails until the latch clicks and

locks in place.

Make sure the power module makes good contact with the

backplane connector of the device.

If you encounter a hard resistance while inserting the power

module, pull out the power module, orient it correctly, and then

insert it again.

Figure 3 Installing the power module

IMPORTANT:

Keep safe the filler panel for the power module slot and the

package for the power module.

Connecting the power cord

WARNING!

•Make sure each power cord has a separate circuit breaker.

•Before connecting the power cord, make sure the circuit

breaker for it is turned off.

To connect the power cord:

1. As shown in Figure 4, connect the female connector of the AC

power cord into the AC-input receptacle on the power module.

Figure 4 Connecting the AC power cord

2. As shown in Figure 5, use a cable tie to secure the power cord to

the handle of the power module.

Figure 5 Securing the AC power cord

3. Connect the other end of the power cord to an external AC

power source and turn on the circuit breaker.

4. Examine the status LED on the power module to verify that the

power module is operating correctly.

Inhaltsverzeichnis

Andere H3C Steuereinheit Handbücher

H3C

H3C PSR250-12A1 Bedienungsanleitung

H3C

H3C SecPath NSQM2AC1400 Bedienungsanleitung

H3C

H3C LSBM1WCM2A0 Bedienungsanleitung

H3C

H3C PSR450-12A Bedienungsanleitung

H3C

H3C SecPath M9000-AI NSQM5MBSHA1 Bedienungsanleitung

H3C

H3C LSVM1S9800FAN Bedienungsanleitung

H3C

H3C SecPath DC2400 Bedienungsanleitung

H3C

H3C SecPath PSR300-12A2 Bedienungsanleitung

H3C

H3C SecBlade Bedienungsanleitung

H3C

H3C PSR6000 Bedienungsanleitung

H3C

H3C SecPath AC2500 Bedienungsanleitung

H3C

H3C SIC-4G-LTE-M Bedienungs- und Wartungsanleitung

H3C

H3C R6900-FAN Bedienungsanleitung

H3C

H3C PSR360-56A Bedienungsanleitung

H3C

H3C LSVM2106SFAN Bedienungsanleitung

H3C

H3C PSR3000-54A Bedienungsanleitung

H3C

H3C PSR750-A Bedienungsanleitung

H3C

H3C SecPath M9000 NSQM1MBFEA0 Bedienungsanleitung

H3C

H3C LSQM1TGT24FD0 Bedienungsanleitung

H3C

H3C PSR300-12A Series Bedienungsanleitung

H3C

H3C LSVM152SCFAN Bedienungsanleitung

H3C

H3C PSR650C-12A Bedienungsanleitung

H3C

H3C LSQM1SDNB0 Bedienungsanleitung

H3C

H3C S9500 LSB1LB1A0 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung