H3C PSR2400-12AHAH-B Bedienungsanleitung

Overview

简介

•The PSR2400-12AHAH-B is a DC output power module that supports AC

and HVDC power input. It provides a maximum output of 2400 W. The

power module has two power inputs: primary power input (input 1) and

secondary power input (input 2). Only input 1 works if you connect power

to both power inputs. PSR2400-12AHAH-B是一款提供直流输出的电源模

块，既支持交流输入也支持高压直流输入。这款电源模块的最大输出功

率可达 2400W。该电源有两路输入，Input 1 为主用输入，Input 2 为备用

输入，两路同时供电时负载在 Input 1。

•The PSR2400-12AHAH-B power module exhausts air from its faceplate.

The following figure shows the PSR2400-12AHAH-B power module.

PSR2400-12AHAH-B 的风道风向是电源面板侧出风。下图展示

PSR2400-12AHAH-B 的外观。

H3C

PSR2400-12AHAH-B Power Module User

Manual

-5PW100

H3C

PSR2400-12AHAH-B 电源手册-5PW100

BOM: 3101A13R

•The PSR2400-12AHAH-B power module is applicable to multiple switch

models. The applicable switch models might change over time. For

compatibility of the power module with switch models, contact the

marketing personnel or technical support. PSR2400-12AHAH-B适用于多

款交换机产品，其适用机型的准确信息随着时间变化有更新的可能性，

若您需要详细的适配信息，请咨询市场人员或技术支持人员。

•The restrictions for using the PSR2400-12AHAH-B power module

depend on the switch model. For more information, see the installation

guide or hardware information and specifications for the switch.

PSR2400-12AHAH-B 用于不同交换机产品时可能存在不同的使用限制，

具体请参考产品配套安装指导或硬件描述。

Feature

特点

Description

说明

Self-protection

具有保护功能

Provide output undervoltage, input undervoltage, output overvoltage, short

circuit, output overcurrent, and overtemperature protections.

具有输出欠压保护、输入欠压保护、输出过压保护、短路保护、输出限流保护、

过温保护等功能

Redundancy

支持冗余备份

Multiple power modules can be connected in parallel to achieve redundancy

and load sharing.

支持多电源模块并联工作，从而可以实现受电设备电源系统的冗余备份，并且

备份电源间具有负载均流功能

Hot swappable

支持热插拔

You can remove one of power modules in N+N redundancy while the device

is operating. Before removing the power module, disconnect the power

module from the external power supply system.

在设备不断电的情况下，可先断开N+N冗余备份电源系统中某个电源模块与外

置供电系统的连接，然后直接对电源模块进行插拔操作

A power module

shuts down after an input undervoltage, short circuit,

output overcurrent, or overtemperature condition occurs. After the issues

are resolved, it automatically restores power supply.

当电源模块触发输入欠压保护

、短路保护、输出限流保护、过温保护功能时，

电源停止供电。当故障消失后，会自动恢复供电。

A power module

shuts down and is locked after an output overvoltage

condition occurs. It cannot restore power supply automatically after the

issue is resolved. To restore power supply, perform the following tasks:

当电源模块触发输出过压保护功能时，电源锁死，停止供电。当电源模块被

锁死时，其不能自动恢复正常工作，可以采用以下步骤来使电源模块恢复正

常工作：

•Disconnect the power cord from the external power supply system.

首先断开电源线与外置电源系统的连接；

•Disconnect the power cord from the power module and then reconnect it.

接着将电源线插头从电源模块上拔出，然后重新连接电源线至电源模块；

•

Connect the power cord to the external power supply system.

最后连接电源线至外置电源系统。

Technical specifications

电源模块规格

Item

项目

Specifications

规格

AC input

交流输入

Rated input voltage range

额定输入电压范围 100 to 240 VAC @ 50/60 Hz

Max input voltage range

最大输入电压范围 90 to 290 VAC @ 47 to 63 Hz

Max input current

最大输入电流 16 A

HVDC input

高压直流输入

Rated input voltage range

额定输入电压范围 240 to 378 VDC

Max input voltage range

最大输入电压范围 180 to 400 VDC

Max input current

最大输入电流 16 A

Output voltage 输出电压 12 V

Max output current 最大输出电流

•AC:

100 A: 90 to 176 VAC @ 47 to

63 Hz

200 A: 176 to 290 VAC @ 47

to 63 Hz

•DC: 200 A

Max output power 最大输出功率

•AC:

1200 W: 90 to 176 VAC @ 47

to 63 Hz

2400 W: 176 to 290 VAC @

47 to 63 Hz

•DC: 2400 W

Dimensions (H × W × D)

外形尺寸（高×宽×深） 83 × 73.5 × 225 mm (3.27 × 2.89 × 8.86 in)

Weight 重量 2 kg (4.41 lb)

Operating temperature 工作温度 –10°C to +55°C (14°F to 131°F)

Relative humidity 工作环境相对湿度（非凝露） 5% RH to 95% RH, noncondensing

Storage temperature 存储温度 -40°C to +70°C (–40°F to +158°F)

LEDs

电源模块状态指示灯

The PSR2400-12AHAH-B power module provides three LEDs on its faceplate to

indicate the power input and output status. PSR2400-12AHAH-B 电源模块面板上

有三个电源模块指示灯，用于指示电源的输入、输出状态。

LED

指示灯

Mark

面板标示

Status

状态

Description

含义

Output status LED

输出状态指示灯 OUT

Steady green

绿色常亮 Normal power output.

输出正常

Steady red

红色常亮

Abnormal power output.

The power module has

generated an alarm for

power issues (such as

output overcurrent, output

overvoltage, input

undervoltage,

overtemperature, or

remote shutdown), and

has entered protection

state.

输出异常（电源在输出过

流、输出过压、输入欠压、

电源温度过高、远程关闭等

情况下告警，并进入自我保

护状态）

Steady amber

橙色常亮

An overtemperature

condition has occurred.

电源温度过高警告

Off

灭No power output.

无输出

Input status LED1

输入状态指示灯1 IN1

Steady green

绿色常亮 Normal power input.

输入正常

Steady red

红色常亮

An input overvoltage or

input undervoltage

condition has occurred.

Input 2 or a parallel power

module on the switch is

operating correctly.

输入过欠压，12Vsb有反供

电

Off

灭No power input.

无输入

LED

指示灯

Mark

面板标示

Status

状态

Description

含义

Input status LED2

输入状态指示灯2 IN2

Steady green

绿色常亮 Normal power input.

输入正常

Steady red

红色常亮

An input overvoltage or

input undervoltage

condition has occurred.

Input 1 or a parallel power

module on the switch is

operating correctly.

输入过欠压，12Vsb有反供

电

Off

灭No power input.

无输入

Installing and removing the power module

电源模块的安装

和拆卸

1. Safety precautions 安全注意事项

•

Wear an ESD wrist strap and make sure the wrist strap makes good skin

contact.

在安装和拆卸电源模块时请注意佩戴防静电腕带，并确保防静电腕带与皮

肤良好接触。

•Before installing the power module, make sure the operating voltage of

the external power supply system is as required by the power module,

and the output voltage of the power module

is as required by the powered

device.

在安装电源模块前，请确认外置供电系统的工作电压同电源模块所标电

压、电源模块输出电压同受电设备所需电压是否相符，避免对电源模块和

受电设备造成损坏。

•To avoid bodily injury, do not touch any bare wire or terminal.

不要接触露出的任何导线、端子部分，以免对人体造成伤害。

•To avoid power module damage, do not open the power module. When

the internal circuits or components of the power module

fail, contact H3C

Support.

为了防止电源模块受损，请不要随意打开电源模块外壳，当电源模块内部

线路或元器件出现故障时，请移交维修人员进行检修。

•Before installing or removing the power module, make sure no power

cord is connected to the power module.

安装和拆卸电源模块时应确保电源模块上没有连接电源线。

2. Tools 工具准备

An ESD wrist strap is required for installing and removing the power module

and connecting the power cord. Prepare an ESD wrist strap yourself.

安装和拆卸电源模块和电源线过程中需要使用防静电腕带，请用户自备。

3. Installing the power module 安装电源模块

•To prevent damage to the power module or the connector on the

backplane of the powered device, insert the power module gently.

为了避免损坏电源模块或受电设备背板的连接器端子，在电源模块插入过

程中动作要缓慢。

•If you insert the power module upside down, you will encounter a hard

resistance because of the special structure designs of the slot and power

module. You need to pull out the power module, orient it correctly, and

insert it again.

如果上下倒置，安装过程将受插槽和电源模块特意设计的结构限制，不能

顺利进行，必须先拔出模块，然后重新插入。

•Before installing the power module

on a switch, make sure it matches the

switch model. For more information, see the installation guide for the

switch. 安装前请检查电源模块型号与设备是否匹配，具体请参见各产品

的安装指导。

•Keep the filler panel, packaging box, and packaging bags for the power

module secure for future use. 请妥善保管假面板及电源模块的包装盒、

包装袋等物品，以备将来需要时使用。

•Before you install a power module, remove the filler panel or power

module slot adapter (if any) from the target slot. The

following procedure

describes how to install a power module when a power module slot

adapter is installed in the slot. 如果电源槽位有电源假面板和电源转接滑

道，请先拆卸下电源假面板和电源转接滑道。如下以电源槽位存在电源

转接滑道的情况为例介绍。

(1) Use a screwdriver to loosen the captive screw on the power module slot

adapter. 安装电源模块前，请先拆卸电源转接滑道，逆时针方向旋转螺丝刀，

拧松松不脱螺钉。

(2) Hold the power module slot adapter with your right thumb pressing the front

panel and other fingers put into the hole.用右手大拇指顶住电源转接滑道的前

面板，其他手指抠住电源转接滑道侧面的凹槽。

(3) Pull the power module slot adapter part way out of the slot, and then pull it

rightwards until the tabs on its left side disengage the chassis. Pull the power

module slot adapter out of the slot.将电源转接滑道向外拉出一些，然后向右拉，

使电源转接滑道左侧的卡扣与设备脱离。最后将电源转接滑道向外拉出。

(4) Unpack the power module and verify that the input mode of the power module

is as required. 从电源模块包装盒中取出电源模块，确认电源模块的输入方式

与所需一致。

(5) Correctly orient the power module (with the latch below the handle). Grasping

the power module handle with one hand and supporting its bottom with the

other, slide the power module slowly along the guide rails into the slot. Make

sure the latch on the power module clicks into place. 保证电源模块上下方向正

确（请保证电源模块的锁闩位于拉手下方），用一只手握住电源模块上的拉手，

另一只手托住电源模块底部，将其后端对准电源插槽，使电源模块沿电源插槽

水平插入插槽。当电源模块完全插入插槽时，会听到电源模块上的锁闩卡住插

槽的声音。

If the power module slot has a fillerpanel, put your fingerinto the hole in the

filler panel, and then pull the filler panel out of the slot gently. 若准备安装电

源模块的电源槽位上有电源假面板，请先拆卸电源假面板。拆卸方法：将

手指伸入圆孔勾住圆孔边缘，沿插槽导轨向外轻微用力拉出假面板。

4. Connecting the power cord 连接电源线

•Use the power cord provided with the power module for connection. 请使

用电源模块标配的电源线进行连接。

Provide a separate circuit breaker for each power cord. 请保证电源线有

独立的输入断路器。

•Before connecting a power cord, make sure the circuit breaker for the

power feed is turned off. 连接电源线前，请将需要连接电源线的输入端断

路器置于断开状态。

(1) Connect the female connectors of the two power cords to power input1 and

power input2 on the power module, respectively. 将两根电源线带插孔的一端

分别插到电源模块的输入插口 1和电源模块的输入插口 2上。

(2) Use two releasable cable ties to secure the power cords to the handle of the

power module, respectively. 用两根可拆卸式扎带将两根电源线分别固定到电

源模块的拉手处，以防电源线脱落。

5. Removing the power module 拆卸电源模块

•To avoid bodily injury or switch damage, strictly follow the procedure

described in this section to remove the power module. 请严格按照如下操

作顺序拆卸电源模块，否则可能会造成设备损坏或者人身伤害。

•If you are not to install a new power module after removing the old one,

install a filler panel in the slot in time. 如果该电源插槽中不再安装电源模

块，请将假面板安装到该插槽上，以免灰尘进入机箱。

(1) Turn off the circuit breaker for each power feed to the power module. 断开电源

输入端断路器。

(2) Remove the releasable cable ties from the power cords, and then remove the

power cords. 松开固定电源线的可拆卸式扎带，并拔出电源线。

(3) Pressing the latch towards the handle direction, pull the power module part

way out of the slot. 向拉手侧掰动锁闩，同时沿插槽导轨向外拉动电源模块，

将电源模块拉出来一部分。

(4) Grasping the power module handle with one hand and supporting its bottom

with the other, pull the power module slowly out of the slot along the guide rails.

用一只手握住电源模块拉手，另一只手托住电源模块下方，将电源模块沿着插

槽导轨水平缓慢地拉出。

(5) Put the removed power module into an antistatic bag. 将拆卸下来的电源模块

放到防静电袋中。

, New H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.

本文档中的信息如有更改，恕不另行通知

如需了解产品及安装方面的更多信息，请登录 H3C网站 www.

h3c.com

Andere H3C Steuereinheit Handbücher

H3C

H3C S12500 LST1LB1A1 Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Bedienungsanleitung

H3C

H3C EWPA1PCID Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB04B0 Bedienungsanleitung

H3C

H3C R6900-FAN Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM-200 Bedienungsanleitung

H3C

H3C PSR180-56A Bedienungsanleitung

H3C

H3C PSR360-56A Bedienungsanleitung

H3C

H3C NSQ1TGS32SF0 Bedienungsanleitung

H3C

H3C PSR450-12A Bedienungsanleitung

H3C

H3C NSQ1FAB04B0 Bedienungsanleitung

H3C

H3C LSQM1TGT24FD0 Bedienungsanleitung

H3C

H3C S9500 LSB1LB1A0 Bedienungsanleitung

H3C

H3C PSR6000 Bedienungsanleitung

H3C

H3C LSWM18CQ Bedienungsanleitung

H3C

H3C LSXM1SEERBXD2 Bedienungsanleitung

H3C

H3C PSR1800-56A Bedienungsanleitung

H3C

H3C LSWM116FC Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB08D0 Bedienungsanleitung

H3C

H3C S9500E LSR1FW2A1 Bedienungsanleitung

H3C

H3C PSR150-A1 Bedienungsanleitung

H3C

H3C LSVM2106SFAN Bedienungsanleitung

H3C

H3C LSBM1WCM2A0 Bedienungsanleitung

H3C

H3C SecPath PSR300-12A2 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung