H3C SecPath PSR300-12A2 Bedienungsanleitung
H3C SecPath PSR300-12A2 &
PSR300-12D2 Power Modules
User Manual
New H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6W101-20190307
Copyright © 2017-2019, New H3C Technologies Co., Ltd.
and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form
or by any means without prior written consent of New H3C
Technologies Co., Ltd.
Trademarks
Except for the trademarks of New H3C Technologies Co., Ltd., any
trademarks that may be mentioned in this document are the property
of their respective owners.
Notice
The information in this document is subject to change without notice.
All contents in this document, including statements, information, and
recommendations, are believed to be accurate, but they are
presented without warranty of any kind, express or implied. H3C shall
not be liable for technical or editorial errors or omissions contained
herein.
Documentation feedback
You can e-mail your comments about product documentation to
We appreciate your comments
i
Contents
Overview ·················································· 1
Introduction···································································· 1
Technical specifications ··················································· 1
Views ··········································································· 2
LEDs············································································ 3
Installing and removing the power module······· 5
Safety precautions ·························································· 5
Tools············································································ 5
Installing and removing the power module ··························· 5
Installing the power module ·········································· 6
Connecting the power cord··········································· 8
Removing the power module········································10
1
Overview
Introduction
The PSR300-12A2 is an AC-input and DC-output power module. The
PSR300-12D2 is a DC-input and DC-output power module. They
provide a maximum output power of 300 W.
The PSR300-12A2 and PSR300-12D2 power modules have the
following features:
•Self-protected against input overcurrent, input undervoltage,
output overvoltage, output short-circuit, and overtemperature.
•Support for 1+1 redundancy and load sharing.
•Hot swappable.
Technical specifications
Table 1 Technical specifications
Item Specifications
Rated input voltage
•PSR300-12A2: 100 VAC to 240
VAC
•PSR300-12D2: –48 VDC to –60
VDC
Output voltage 12 V
Maximum output current 25 A
Maximum output power 300 W
Dimensions (H × W × D) 40.13 × 101.6 × 234.9 mm (1.58 ×
4.00 × 9.25 in)
2
Item Specifications
Operating temperature 0°C to 55°C (32°F to 131°F)
Operating humidity 5% RH to 95% RH, non-condensing
Views
Figure 1 PSR300-12A2
1
2
3
4
56
8
7
3
Figure 2 PSR300-12D2
(1) Power switch ("O" represents off and "—" represents on)
(2) Power receptacle (3) Spring tab
(4) Handle (5) Power output status LED
(6) Power input status LED (7) Bail clasp mounting holes
(8) Captive screw
(9) Screw holes for securing the power cord connector
LEDs
The power module uses power input and power output LEDs to
indicate the power input and output status, respectively.
4
Table 2 LED description
LED Status Description
Power input status
LED (AC OK or
Input)
Off No power is being input or an
input failure has occurred.
On Normal power input.
Power output status
LED (DC OK or
Output)
Off No power is being output or an
output failure has occurred.
On Normal power output.
If the power input LED is on but the output LED is off, an output issue
might have occurred. To resolve the issue:
1. Turn off the power switch on the power module and reconnect
the power cord.
This operation resolves the power module failure caused by an
output overvoltage, output short-circuit, or output overcurrent
condition. The power module shuts down and latches off if one
of these conditions occurs and cannot automatically restore
operation.
2. If the issue persists, the temperature might be high. Take
measures to decrease the temperature to an acceptable range.
The power module will automatically restore operation.
5
Installing and removing the power
module
Safety precautions
To avoid possible bodily injury and power module and device
damage, follow these safety precautions:
•When installing and removing the power module, always wear
an ESD wrist strap and make sure it makes good skin contact.
•Make sure the voltage of the power source is as required by the
power module, and the output voltage of the power module is as
required by the device.
•To avoid bodily injury, do not touch any bare wire or terminal.
•Do not place the power module in a wet location, and prevent
liquid from flowing into the power module.
•To avoid power module damage, do not open the power module.
If the internal wires or units are faulty, contact H3C Support.
Tools
When installing and removing a power module and power cord, you
must wear an ESD wrist strap. Prepare it yourself.
Installing and removing the power module
The installation and removal procedures are similar for the
PSR300-12A2 and PSR300-12D2 power modules. The following
procedures use the PSR300-12D2 power module as an example.
6
Installing the power module
CAUTION:
To avoid bodily injury and device damage, strictly follow the
procedure in Figure 3 to install the power module.
Figure 3 Power module installation procedure
To install the power module:
1. Wear an ESD wrist strap and make sure the strap makes good
skin contact and is reliably grounded.
2. Unpack the power module and make sure the power module
model is as required.
Keep the power module package secure for future use.
3. As shown in Figure 4, correctly orient the power module (with
the lettering on it upwards). Grasping the module handle with
one hand and supporting the module bottom with the other,
push the module slowly into the slot along the guide rails. Make
sure the power module has good contact with the backplane
connectors.
7
The power module and power module slot are designed to
prevent disorientation and misalignment. If you cannot insert the
power module smoothly into the slot, the orientation might be
wrong or the power module is not aligned correctly with the slot.
Pull out the power module, reorient the power module or realign
it with the slot, and insert it again.
4. When the power module is fully seated in the slot, fasten the
captive screw on the power module.
Figure 4 Installing the power module
1
2
Andere Handbücher für SecPath PSR300-12A2
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere H3C Steuereinheit Handbücher
H3C
H3C SecBlade Bedienungsanleitung
H3C
H3C SecPath M9000-AI NSQM5MBSHA1 Bedienungsanleitung
H3C
H3C PSR1600B-12A-B Bedienungsanleitung
H3C
H3C PSR250-12A Bedienungsanleitung
H3C
H3C SecPath PSR300-12A2 Bedienungsanleitung
H3C
H3C SecPath AC2500 Bedienungsanleitung
H3C
H3C SecPath M9000-AI NSQM5AIASKA1 Bedienungsanleitung
H3C
H3C PSR180-56A Bedienungsanleitung
H3C
H3C PSR2400-54D Bedienungsanleitung
H3C
H3C S9500E LSR1FW2A1 Bedienungsanleitung
H3C
H3C PSR150-A1 Bedienungsanleitung
H3C
H3C SIC-4G-LTE-M Bedienungs- und Wartungsanleitung
H3C
H3C LSVM1S9810FAN Bedienungsanleitung
H3C
H3C SecPath NSQ1FAB04B0 Bedienungsanleitung
H3C
H3C SR6600 SPE-FWM-200 Bedienungsanleitung
H3C
H3C SR6600 SPE-FWM Bedienungsanleitung
H3C
H3C S12500 LST1LB1A1 Bedienungsanleitung
H3C
H3C R6900-FAN Bedienungsanleitung
H3C
H3C PSR2400-12AHAH-B Bedienungsanleitung
H3C
H3C LSVM2106SFAN Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
