H3C S12500CR Series Bedienungsanleitung

Contents

1 Preparing for installation··········································································1-1

Safety recommendations ································································································································1-1

General safety recommendations···········································································································1-1

Electricity safety······································································································································1-1

Handling safety ·······································································································································1-1

ESD prevention·······································································································································1-2

Laser safety·············································································································································1-2

Examining the installation site·························································································································1-2

Weight support········································································································································1-2

Temperature············································································································································1-2

Humidity··················································································································································1-3

Cleanliness··············································································································································1-3

EMI··························································································································································1-4

Grounding ···············································································································································1-4

Power······················································································································································1-4

Cooling····················································································································································1-4

Space······················································································································································1-5

Installation accessories···························································································································1-6

1-1

1 Preparing for installation

H3C S12500CR Ethernet Switch Router Series includes the following models:

•

S12516CR

•

S12508CR

Safety recommendations

To avoid possible bodily injury and equipment damage, read Compliance and Safety Manual

provided with the device and all safety recommendations in this chapter carefully before installation.

The recommendations do not cover every possible hazardous condition.

General safety recommendations

•

Keep the device clean and dust-free.

•

Do not place the device on a moist area, and avoid liquid flowing into the device.

•

Make sure the ground is dry and flat and anti-slip measures are in place.

•

Keep the device and installation tools away from walk areas.

•

Do not wear loose clothing, jewelry (for example, necklace) or any other things that could get

caught in the device when you install and maintain the device.

Electricity safety

•

Clear the work area of possible electricity hazards, such as ungrounded power extension

cables, missing safety grounds, and wet floors.

•

Locate the emergency power-off switch in the room before installation so you can quickly shut

power off when an electrical accident occurs.

•

Remove all external cables, including power cords, before moving the chassis.

•

Do not work alone when the device has power.

•

Before performing a task that is hazardous when power is present, make sure the device is

completely powered off.

•

The device is powered off only when both the power switches on the device are off.

Handling safety

CAUTION:

Hold the chassis handles to move the device.

Do not hold the handle of a fan tray, a power supply,

module, or the air vents of the chassis to move the device. Any attempt to move the device with

these parts might cause equipment damage and even bodily injury.

IMPORTANT:

The maximum load-bearing capacity of the chassis handles is 50 kg (110.23 lb).

Remove power supplies, modules, and all external cables, including the power cords, before moving

the chassis. As a best practice, use a mechanical lift, such as forklift truck, to move the chassis.

1-2

If no mechanical lift is used, follow these guidelines to move the chassis:

•

Cooperate with a minimum of four people to move the chassis.

•

Lift the chassis by using the chassis handles or by supporting the bottom from the two sides.

•

Lift and put down the chassis slowly and never move suddenly.

ESD prevention

To prevent the electric component from being damaged by electrostatic discharge (ESD), follow

these guidelines:

•

Ground the device reliably. For how to ground your device, see "Installing the device."

•

Always wear an ESD wrist strap and make sure it is reliably grounded when installing

removable components. For how to use an ESD wrist strap, see "Installing removable

components."

•

Hold a PCB by its edges. Do not touch any electronic components or printed circuit.

•

Put modules away in antistatic bags for future use.

Laser safety

WARNING

Do not stare into any

fiber port or view directly with non-attenuating optical instruments when the

device has power. The laser light emitted from the fiber port might hurt your eyes.

The device is a Class 1 laser product.

Examining the installation site

The device must be used indoors. To ensure correct operation and long lifespan of your device, the

installation site must meet the requirements in this section.

Weight support

Make sure the floor can support the total weight of the rack, chassis, modules, power supplies, and

all other components. To mount the device in a rack, make sure the slide rails can support the total

weight of the device and its accessories (modules, power supplies, and transceiver modules).

Additionally, the floor and slide rail loading plan must also consider system expansion, such as

adding more modules. For more information, see H3C S12500CR Switch Router Series Hardware

Information and Specifications.

Temperature

CAUTION:

If condensation appears on the chassis when you move it to a high

-temperature environment, dry

the chassis before powering it on to avoid short circuits.

To ensure correct operation of the device, make sure the room temperature meets the requirements

in Table 1-1.

1-3

Table 1-1 Temperature requirements

Temperature Range

Operating temperature 0°C to 40°C (32°F to 104°F)

Storage temperature –40°C to +70°C (–40°F to +158°F)

Humidity

Maintain appropriate humidity in your equipment room, as described in Table 1-2.

•

Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

•

Lasting low relative humidity can cause washer contraction and ESD and cause problems

including loose mounting screws and circuit failure.

Table 1-2 Humidity requirements

Humidity Range

Operating humidity 5% to 95%, noncondensing

Storage humidity 5% to 95%, noncondensing

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of

metal components and contact points. In the worst case, electrostatic adsorption can cause

communication failure.

Table 1-3 Dust concentration limit in the equipment room

Substance Concentration limit (particles/m3)

Dust particles ≤ 3 x 104

(No visible dust on desk in three days)

NOTE:

Dust particle diameter ≥ 5 µm

The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and

premature aging of components, as shown in Table 1-4.

Table 1-4 Harmful gas limits in the equipment room

Gas Max. (mg/m3)

SO21.0

H2S 0.5

NH33.0

Cl20.3

1-4

EMI

All electromagnetic interference (EMI) sources, from outside or inside of the device and application

system, adversely affect the device in the following ways:

•

A conduction pattern of capacitance coupling.

•

Inductance coupling.

•

Electromagnetic wave radiation.

•

Common impedance (including the grounding system) coupling.

To prevent EMI, perform the following tasks:

•

If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)

to filter interference from the power grid.

•

Keep the device far away from radio transmitting stations, radar stations, and high-frequency

devices.

•

Use electromagnetic shielding, for example, shielded interface cables, when necessary.

Grounding

Using a good grounding system to protect your device against lightning shocks, interferences, and

ESD is essential to the operating reliability of your device.

Make sure the equipment room grounding system has a resistance value less than 1 ohm.

For more information about grounding the device, see "Installing the device."

Power

Perform the following tasks to meet the power requirements:

1. Calculate the system power consumption.

The system power consumption varies by module type and density. For more information about

system power consumption calculation, see S12500CR Switch Router Series Hardware

Information and Specifications.

2. Identify the number of power supplies.

The total maximum output power of all power supplies must be higher than the system power

consumption. For more information about available power supplies, see S12500CR Switch

Router Series Hardware Information and Specifications.

3. Verify that the power system at the installation site meets the requirements of the power

supplies, including the input method and rated input voltage. For more information about power

supply specifications, see S12500CR Switch Router Series Hardware Information and

Specifications.

Cooling

Plan the installation site for adequate ventilation:

•

Leave a minimum of 30 cm (11.81 in) of clearance at the inlet and outlet air vents.

•

The rack for the device has a good cooling system.

•

The installation site has a good cooling system.

•

Verify that the airflow design of the chassis meets the airflow design of the installation site.

1-5

Figure 1-1 Airflow through the device (S12516CR)

Space

For easy installation and maintenance, follow these space requirements:

•

Reserve a minimum of 1.2 m (3.94 ft) of clearance between the rack and walls or other devices.

•

Make sure the rack has enough space to accommodate the device.

For information about device dimensions and rack requirements, see "Device dimensions and

rack requirements."

1-6

Installation accessories

Before installation, make sure you have all the required installation accessories.

Table 1-5 Installation accessories

Product code Description Quantity Applicable

device models

2150A0GA

S12516CR mounting brackets

1 pair S12516CR

2150A0GB

S12508CR mounting brackets

1 pair S12508CR

2113A2AK S12500CR SEU filler panel 2 All S12500CR

models

1-7

Product code Description Quantity Applicable

device models

2113A2AR

S12500CR interface module filler panel

•S12516CR:

•S12508CR: 8

All S12500CR

models

2114A0B7

S12500CR power supply filler panel

Each power tray

has six power

supply filler

panels.

All S12500CR

models

2114A0D3

S12500CR front power tray filler panel

2 All S12500CR

models

2114A0D4

S12500CR rear power tray filler panel

2 All S12500CR

models

2114A0D1

S12516CR power input area protective

plate

1 S12516CR

2114A0D7

S12508CR power input area protective

plate

1 S12508CR

2150A0G9

S12516CR cable management bracket

•MPU section:

1 kit

•Interface

module

section: 4 kits

S12516CR

2150A0GC S12508CR cable management bracket •MPU section:

1 kit S12508CR

1-8

Product code Description Quantity Applicable

device models

•Interface

module

section: 2 kits

0223A1L9

S12516CR air filter

1 S12516CR

0223A1L8

S12508CR air filter

1 S12508CR

26020075 Cage nut

•S12516CR:

•S12508CR:

All S12500CR

models

26020141 M6 screw

•S12516CR:

•S12508CR:

All S12500CR

models

0404A0EE

Grounding cable

1 All S12500CR

models

28050001

ESD wrist strap

1 All S12500CR

models

04042967

Console cable

1 All S12500CR

models

Andere Handbücher für S12500CR Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere H3C Netzwerk-Router Handbücher

H3C

H3C SR8800 Series Bedienungsanleitung

H3C

H3C SR6600 Series Bedienungsanleitung

H3C

H3C S3100-52P Montageanleitung

H3C

H3C S12516CR Bedienungs- und Wartungshandbuch

H3C

H3C S9500 Series Montageanleitung

H3C

H3C S1016 Bedienungsanleitung

H3C

H3C MSR 20 Series Bedienungsanleitung

H3C

H3C CR16000-M Bedienungs- und Wartungshandbuch

H3C

H3C MSR2600-6-X1-GL Bedienungsanleitung

H3C

H3C S5120-EI Series Bedienungsanleitung

H3C

H3C MSR 930 Bedienungsanleitung

H3C

H3C MSR Series Bedienungsanleitung

H3C

H3C MSR Series Bedienungsanleitung

H3C

H3C S7502 Bedienungsanleitung

H3C

H3C MSR-20-21 ROUTER Bedienungsanleitung

H3C

H3C MSR 2600 Series Bedienungsanleitung

H3C

H3C S5500-HI Switch Series Bedienungsanleitung

H3C

H3C SR6604 Bedienungsanleitung

H3C

H3C H3C S3600 Series Bedienungsanleitung

H3C

H3C S12500R Series Bedienungsanleitung

H3C

H3C CR1606-F Bedienungsanleitung

H3C

H3C S5500-EI series Bedienungsanleitung

H3C

H3C S3100-52P Bedienungsanleitung

H3C

H3C MSR 5600 Installationshandbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise