H3C S12500-X Stücklistenhandbuch

Manual version: 6PW102-20170411 BOM: 3123A0T2

H3C S12500-X LST1FW3B1 Card Manual

1 Card identifier

The card identifier LST1FW3B1 is at the upper right corner of the front panel.

2 Introduction

The LST1FW3B1 card provides one console port, one CF card interface, two USB interfaces, two

10/100/1000BASE-T Ethernet copper interfaces, and two Gigabit Combo interfaces.

You can use a combo interface to provide the following functions:

•In-band management.

•Outgoing interface for log messages.

•Failover interface for stateful failover.

3 Specifications

Figure 1 Front panel

(1) Console port (CONSOLE)

(2) USB ports (hardware reserved, software not support

currently)

(3) 10/100/1000BASE-T copper combo port

(4) 10/100/1000BASE-T copper combo port

LED (LINK/ACT)

(5) 1000BASE-X fiber combo port (6) 1000BASE-X

fiber combo port LED (LINK/ACT)

(7) Alarm LED (ALM) (8) System LED (RUN)

(9) Ejector lever (10)

Captive screw

Table 1 Card specifications

Item S

ecification

Flash 8 MB NOR flash, 16 bit wide

SDRAM

DDR3 SDRAM

2 slots for SDRAMs

Standard configuration: 16 GB (two 8 GB DDR3 SDRAMs)

Two same-sized DDR3 SDRAMs are required.

CF card One built-in CF card slot

256 MB CF card, expandable to 1 GB

Manual version: 6PW102-20170411 BOM: 3123A0T2

Item S

ecification

Dimensions (H × W × D) 40.1 × 399.2 × 512 mm (1.58 × 15.72 × 20.16 in)

Power consumption 190 to 260 W

Weight 5.8 kg (12.79 lb)

Hot swapping Supported

Ports

•1 console port

•2 USB ports ((not supported by the card software)

•2 combo interfaces, which can operate in 10/100/1000BASE-T copper

port mode or 1000BASE-X SFP fiber port mode at a time.

You can use the combo enable { copper | fiber } command to activate either

port. By default, the copper combo port is activated.

Ambient temperature

•Operating: 0°C to 45°C (32°F to 113°F)

•Storage: –40°C to +70°C (–40°F to +158°F)

Ambient humidity

•Operating: 5% RH to 95% RH, noncondensing

•Storage: 5% RH to 95% RH, noncondensing

Compatible device models •H3C S12500-X series switches

System software version See the release notes that come with the card.

Table 2 Console port specifications

Item S

ecification

Connector RJ-45

Interface standard RS-232

Transmission baud rate 9600 bps (default) to 115200 bps

Transmission medium Asynchronous serial cable

Transmission distance ≤15 m (49.21 ft)

Services

•Provides connection to an ASCII terminal.

•Provides connection to the serial port of a local or remote (through a pair

of modems) PC running terminal emulation program.

•Supports command line interface (CLI)

Table 3 10/100/1000BASE-T copper port specifications

Item S

ecification

Connector RJ-45

Interface standard 802.3, 802.3u, and 802.3ab

Interface type MDI/MDIX autosensing

Supported cable Category-5 (or above) twisted pair cable

Transmission distance 100 m (328.08 ft)

Port transmission rate

•10 Mbps, half/full duplex

•100 Mbps, half/full duplex

•1000 Mbps, full duplex

Manual version: 6PW102-20170411 BOM: 3123A0T2

iii

Table 4 1000BASE-X fiber port specifications

Item S

ecification

Transceiver module SFP

Connector type LC

Interface standard 802.3, 802.3u, and 802.3ab

Operating mode 1000 Mbps, full duplex

Table 5 1000BASE-X SFP port specifications

Gigabit SFP module Central

wavelength

Connector

Cable specifications

Maximum

transmission

distance

SFP-GE-SX-MM850-A 850 nm LC 62.5/125μm

multi-mode optical fiber 0.55 km (0.34 miles)

SFP-GE-LX-SM1310-A 1310 nm LC 9/125 μm single-mode

optical fiber 10 km (6.21 miles)

SFP-GE-LH40-SM1310 1310 nm LC 9/125 μm single-mode

optical fiber 40 km (24.86 miles)

SFP-GE-LH40-SM1550 1550 nm LC 9/125 μm single-mode

optical fiber 40 km (24.86 miles)

SFP-GE-LH80-SM1550 1550 nm LC 9/125 μm single-mode

optical fiber 80 km (49.71 miles)

SFP-GE-LH100-SM1550 1550 nm LC 9/125 μm single-mode

optical fiber 100 km (62.14 miles)

4 LEDs

The card provides LEDs to show the operating status of the card and interfaces.

Table 6 LED description

LED Status Descri

tion

Alarm LED (ALM)

Off The system is operating correctly.

Steady red

The system is in an alarm condition, and immediate

action is required.

To identify the problem, use the system log.

System LED (RUN)

Off No power is input, or the card is faulty.

Steady green The system is not operating correctly.

Flashing green (1 Hz) The system has started up and is operating correctly.

Flashing green (8 Hz) The system is loading the software or is not ready.

Combo interface LED

(LINK/ACT)

Off No link is present on the port.

Steady green A link is present on the port.

Flashing green The port is sending or receiving data.

Manual version: 6PW102-20170411 BOM: 3123A0T2

5 Installing and removing the card

CAUTION:

•Wear a well-grounded ESD wrist strap or ESD gloves before you install or remove the card.

•Do not touch the components on the PCB.

5.1 Installing the card

1. Remove the filler panel from the slot for the card at the front of the switch.

This example uses slot 7.

2. Place the card vertically with the surface-mounted components facing left. Pull the ejector levers

outward, and then gently push the card in along the slot guide rails until the card is in close contact

with the backplane.

3. Push the ejector levers inward.

4. Tighten the captive screws with a Phillips screwdriver to secure the card in the slot.

Figure 2 Installing the card

5.2 Removing the card

1. Use a Phillips screwdriver to loosen the captive screws at both sides of the card.

2. Pull the ejector levers at both sides of the card outward to separate it from the backplane, and then

pull the card along the guide rails to remove it from the chassis.

Manual version: 6PW102-20170411 BOM: 3123A0T2

3. Place the card on an anti-static workbench with the surface-mounted components up. You can also

put it in an anti-static bag.

4. If you are not going to install a new card, install a filler panel to prevent dust and ensure good

ventilation in the switch.

6 Logging in to the card

The card uses an independent operating system. Before you can configure the card, you must log in to

the card by using one of the following methods:

•Log in from the switch's CLI through the oap connect command.

•Log in through the card's Web, console port, or Telnet.

H3C recommends that you log in to the card from the switch's CLI the first time you access the card. This

section includes a procedure for logging in from the switch's CLI. For more information about other login

methods, see H3C SecPath Series High-End Firewalls Configuration Guides.

To log in to the card from the switch's CLI, perform the following task in user view:

Task Command

Remarks

•In standalone mode:

oap connect slot slot-number

•In IRF mode:

oap connect chassis

chassis-number slot

slot-number

To return to the CLI interface of the

switch, press Ctrl+K.

7 Software upgrade

The card uses independent BootWare and system software images. You must upgrade the card software

separately from the switch software. To ensure a successful card upgrade, H3C recommends that you

upgrade the card through the card's console port or management Ethernet port. For more information

about software upgrade of the card, see the release notes that come with the card.

8 Obtaining documentation

To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:

1. Go to http://www.h3c.com.hk/Technical_Documents.

2. Click Security Products, and then choose the desired product.

Andere Handbücher für S12500-X

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere H3C Schalten Handbücher

H3C

H3C S12500 Series Bedienungsanleitung

H3C

H3C S5500-EI series Bedienungsanleitung

H3C

H3C H3C S7500E Series Bedienungs- und Wartungshandbuch

H3C

H3C H3C S5600 Series Bedienungsanleitung

H3C

H3C S6890 Series Kurzanleitung

H3C

H3C S5120-HI Series Bedienungsanleitung

H3C

H3C S5120-HI Series Bedienungsanleitung

H3C

H3C S6890 Series Bedienungsanleitung

H3C

H3C S5810 Series Bedienungsanleitung

H3C

H3C S6890-30HF Bedienungs- und Wartungshandbuch

H3C

H3C S5120-EI Series Bedienungsanleitung

H3C

H3C S12500-X Installationshandbuch

H3C

H3C S12500G-AF Series Bedienungsanleitung

H3C

H3C S7500 Series Bedienungsanleitung

H3C

H3C S5560S-EI Series Bedienungsanleitung

H3C

H3C S6520X-30QC-EI Bedienungsanleitung

H3C

H3C 6W101 Bedienungs- und Wartungshandbuch

H3C

H3C S7502 Bedienungsanleitung

H3C

H3C H3C S3600 Series Montageanleitung

H3C

H3C S3600-28PSI Benutzerhandbuch

H3C

H3C S6860 Series Bedienungsanleitung

H3C

H3C S9500E Series Bedienungsanleitung

H3C

H3C S5560S-SI Bedienungsanleitung

H3C

H3C S9500 Series Montageanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch