H3C S7500 Series Bedienungsanleitung
Installation Manual
H3C S7500 Series Ethernet Switches Table of Contents
i
Table of Contents
Chapter 5 System Commissioning..............................................................................................5-1
5.1 Configuration Environment Setup......................................................................................5-1
5.1.1 Setting up Networking Environment........................................................................5-1
5.1.2 Connecting the Console Cable ...............................................................................5-1
5.1.3 Setting Terminal Parameters ..................................................................................5-1
5.2 Power-on Startup...............................................................................................................5-5
5.2.1 Check before Power-on ..........................................................................................5-5
5.2.2 Power-on.................................................................................................................5-6
5.2.3 Check after Power-on (Recommended) .................................................................5-6
5.2.4 Startup Process.......................................................................................................5-6
Installation Manual
H3C S7500 Series Ethernet Switches Chapter 5 System Commissioning
5-1
Chapter 5 System Commissioning
5.1 Configuration Environment Setup
5.1.1 Setting up Networking Environment
zThe terminal (a PC in this example) is connected to the console port of the switch
with a console cable.
Console cable
P
C
Switch
Connect to the serial
port
Connect to the
Console port
Figure 5-1 Network diagram for switch configuration
5.1.2 Connecting the Console Cable
Follow these steps to connect the console cable:
1) Connect the DB-9 female connector of the console cable to the serial port of the
PC.
2) Connect the RJ-45 connector of the console cable to the console port of the
switch.
5.1.3 Setting Terminal Parameters
Parameter requirements:
zBits per second: 9600
zData bits: 8
zParity check: None.
zStop bits: 1.
zFlow control: None.
zTerminal emulation: VT100.
The following illustrates how to set terminal parameters on the PC running Windows XP
HyperTerminal.
Step 1: Start the PC and run the terminal emulator.
Installation Manual
H3C S7500 Series Ethernet Switches Chapter 5 System Commissioning
5-2
Step 2: Set the parameters for Windows XP HyperTerminal as follows:
zBits per second: 9600
zData bits: 8.
zParity check: None
zStop bits: 1
zFlow control: None
zTerminal emulation: VT100
The parameter setting procedure is as follows:
1) Select Start > Programs/All Programs > Accessories > Communications >
HyperTerminal to enter the HyperTerminal window to establish a new connection
and the system displays the Connection Description dialog box.
Figure 5-2 Connection description of HyperTerminal
2) Enter the name of the new connection in the Connection Description dialog box
and click OK. Then the system displays the Connect To dialog box.
3) Select the serial port to which the cable is connected from Connect using
dropdown list.
Installation Manual
H3C S7500 Series Ethernet Switches Chapter 5 System Commissioning
5-3
Figure 5-3 Select the serial port for hyper terminal connection
4) Click OK. The system displays the serial port parameters setting dialog box as
shown in Figure 5-4.
5) Set the bits per second to 9600, data bits to 8, parity check to none, stop bits to 1
and flow control to none.
Figure 5-4 Set the serial port parameters
Installation Manual
H3C S7500 Series Ethernet Switches Chapter 5 System Commissioning
5-4
6) Click OK. The system enters the HyperTerminal dialogue box as shown in Figure
5-5.
Figure 5-5 HyperTerminal dialog box
7) In the HyperTerminal dialogue box, click the properties icon to open the Switch
Properties dialog box.
8) Click the Settings tab, set the terminal emulation to VT100, and click OK (see
Figure 5-6).
Installation Manual
H3C S7500 Series Ethernet Switches Chapter 5 System Commissioning
5-5
Figure 5-6 Set the terminal emulation
5.2 Power-on Startup
5.2.1 Check before Power-on
Before powering on the switch, make sure that:
zThe switch is mounted steadily.
zAll boards are correctly installed.
zAll communication cables, fibers, power cables, and grounding cables are
correctly connected.
zThe power outlet voltage is the same as the one indicated on the switch label.
zThe console cable is correctly connected, the PC or terminal for configuration is
started, and the terminal parameter settings are completed.
Installation Manual
H3C S7500 Series Ethernet Switches Chapter 5 System Commissioning
5-6
Caution:
Before powering on the switch, locate the position of the power switch for the
equipment room where you will operate so that you can switch off the power supply
promptly in case of any accident
5.2.2 Power-on
zTurn on the power to the system.
zTurn on the power switch on the system.
5.2.3 Check after Power-on (Recommended)
After powering on the switch, check that:
zThe cooling system works normally. You can hear the fans rotate and feel airflows
out of the vent.
zThe system LEDs on the SRPU work normally.
After that, make corresponding configurations.
5.2.4 Startup Process
As the switch is started, the following information will be output on the configuration
terminal:
Note:
The following information may vary with switch models.
******************************************
* *
* H3C S7506 BOOTROM, Version 530 *
* *
******************************************
Copyright(c) 2004-2007 Hangzhou H3C Tech. Co., Ltd.
Creation date : Apr 20 2007, 14:48:52
CPU type : MPC8245
CPU Clock Speed : 300Mhz
BUS Clock Speed : 33Mhz
Installation Manual
H3C S7500 Series Ethernet Switches Chapter 5 System Commissioning
5-7
BOOT_FLASH type : M29W040B
Flash Size : 32MB
Memory Size : 256MB
S7506 main board self testing................................
SDRAM Data lines Selftest.................................OK!
SDRAM Address lines Selftest..............................OK!
SDRAM fast selftest.......................................OK!
Please check LEDs.....................LEDs selftest finished!
CPLD selftest.............................................OK!
FPGA selftest.............................................OK!
The switch Mac address is .....................0000.0309.0004
Press Ctrl+B to enter Boot Menu... 5
Auto-booting...
Auto booting file is srpuprj.app
Decompress Image...................................................
.......................................................OK!
Starting at 0x60000...
..........................................................................
..........................................................................
..........................................................................
....................
User interface Aux0/0 is available
Press ENTER to get started.
The display of the above information indicates the completion of the switch
auto-startup.
Press Enter. The following prompt appears on the configuration terminal, which
indicates that you can start configuring the switch.
<H3C>
Note:
H3C S7500 series switches provide a variety of command views. For the specific
descriptions on the configuration commands and command line interfaces, refer to
H3C S7500 Series Ethernet Switches Operation Manual and H3C S7500 Series
Ethernet Switches Command Manual.
Andere Handbücher für S7500 Series
29
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere H3C Schalten Handbücher
H3C
H3C S3100V2-52TP Bedienungsanleitung
H3C
H3C LSW1SP4P0 Bedienungsanleitung
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C HSW-2024G Bedienungsanleitung
H3C
H3C CR19000-16 Bedienungs- und Wartungshandbuch
H3C
H3C S6860-30HF Bedienungs- und Wartungshandbuch
H3C
H3C H3C S7500E Series Installationshandbuch
H3C
H3C S3610 Series Bedienungsanleitung
H3C
H3C S7500 Series Bedienungsanleitung
H3C
H3C S7500 Series Bedienungsanleitung
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C S7500E-XS Series Bedienungsanleitung
H3C
H3C S9500E Series Bedienungsanleitung
H3C
H3C S6520X-SI Series Bedienungsanleitung
H3C
H3C S3100 Series Bedienungsanleitung
H3C
H3C S5120-EI Series Installationshandbuch
H3C
H3C S5500-HI Switch Series Installationshandbuch
H3C
H3C S5500-EI series Bedienungsanleitung
H3C
H3C WX3000 Series Bedienungsanleitung
H3C
H3C S10500X Series Bedienungsanleitung
