H3C SecPath NSQ1FAB12D0 Bedienungsanleitung
Manual version: 6PW106-20210319 BOM: 3123A0R1
i
H3C SecPath NSQ1FAB12D0 switching fabric module
1 Module view
The NSQ1FAB12D0 switching fabric module uses product code NSQM1FAB12D0.
Figure 1 NSQ1FAB12D0 switching fabric module
2 Specifications
Figure 2 Front panel
(1) Console port (CONSOLE) (2) Status LEDs
Table 1 Module specifications
Item Specifications
Dimensions (H × W × D) 40 × 602 × 298 mm (1.57 × 23.70 × 11.73 in)
Power consumption 195 W to 255 W
Weight 4.51 kg (9.94 lb)
Hot swapping Supported
Connector type RJ-45
Ports 1 × console port
Ambient temperature •Operating: 0°C to 45°C (32°F to 113°F)
•Storage: –40°C to +70°C (–40°F to +158°F)
Ambient humidity •Operating: 10% RH to 95% RH, noncondensing
•Storage: 5% RH to 95% RH, noncondensing
Compatible device models
and slots
•M9014 gateway (slots 14 to 17)
•T9014 IPS (slots 14 to 17)
Manual version: 6PW106-20210319 BOM: 3123A0R1
ii
IMPORTANT:
A
n M9014 gateway and a T9014 IPS each require a minimum of three switching fabric modules, and
slots 14 and 15 must be installed with switching fabric modules.
3 LEDs
The module provides LEDs to show its operating status.
Table 2 LED description
RUN LED ALM LED Description
Flashing (0.5 Hz) Off The switching fabric module is operating properly.
Off On The switching fabric module is faulty.
Flashing (0.5 Hz) On The temperature of the switching fabric module has exceeded the
upper or lower limit.
Off Off The switching fabric module has not started.
On Off The switching fabric module is starting up.
4 Installing or removing the module
CAUTION:
•Wear a well-grounded ESD-preventive wrist strap before you install or remove the module.
•When you install or remove the module, avoid touching the components on it.
4.1 Installing the module
1. Face the rear panel of the device.
2. Remove the filler panel from the target slot.
This example uses slot 15.
3. Place the module vertically with the component side facing left. Open the ejector levers and
gently push the module into the slot along the guide rails, as shown by callout 1 in Figure 3.
4. Close the ejector levers. Make sure the module is in close contact with the backplane, as shown
by callout 2 in Figure 3.
5. Use a Phillips screwdriver to fasten the captive screws on the module, as shown by callout 3
in Figure 3.
Manual version: 6PW106-20210319 BOM: 3123A0R1
iii
Figure 3 Installing the module
(1) Gently push the module into the slot along the guide rails until the module is in close contact with the
backplane.
(2) Close the ejector levers.
(3) Use a Phillips screwdriver to fasten the captive screws.
(4) Installation is finished.
4.2 Removing the module
1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is
released.
2. Simultaneously open the ejector levers on the module to separate the module from the
backplane, and pull the module slowly out of the chassis along the guide rails.
3. Place the module on an anti-static workbench or put it in an anti-static bag, with the component
side facing up.
If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure
good ventilation in the device.
Copyright © 2021 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
1 2
3 4
Andere H3C Schalten Handbücher
H3C
H3C S6800 Series Bedienungsanleitung
H3C
H3C LSWM124TG2H Bedienungsanleitung
H3C
H3C S5120-EI Series Installationshandbuch
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C S6825 Series Bedienungsanleitung
H3C
H3C S6805 Series Betriebsanleitung
H3C
H3C S9825 Series Bedienungsanleitung
H3C
H3C S3100V2-52TP Bedienungs- und Wartungshandbuch
H3C
H3C S7500 Series Bedienungsanleitung
H3C
H3C S10500 Series Bedienungsanleitung
H3C
H3C E500C-F Series Bedienungsanleitung
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C S5500-SI Series Bedienungsanleitung
H3C
H3C S7500X Series Bedienungsanleitung
H3C
H3C S10512 Bedienungsanleitung
H3C
H3C S6520X-EI Series Bedienungsanleitung
H3C
H3C S6300 Series Bedienungsanleitung
H3C
H3C S6890 Series Kurzanleitung
H3C
H3C S5130-28F-EI Bedienungsanleitung
H3C
H3C s5820x series Bedienungsanleitung
