H3C WA6622 Bedienungsanleitung

Contents

1 Preparing for installation······························································· 1-1

Safety recommendations ·········································································································· 1-1

Site preparation ······················································································································ 1-1

Installation accessories ············································································································ 1-1

Installation tools······················································································································ 1-2

2 Installing the AP ········································································· 2-1

Installation flowchart ················································································································ 2-1

Pre-installation tasks················································································································ 2-1

Determining the installation position ···························································································· 2-1

Mounting the AP ····················································································································· 2-2

Mounting the AP on a wall·································································································· 2-2

Mounting the AP on a ceiling ······························································································ 2-4

Connecting the AP to a power source·························································································· 2-5

Connecting a PoE power source·························································································· 2-5

Connecting a local power source ························································································· 2-6

Check after power-on ········································································································ 2-6

Connecting the AP to the network······························································································· 2-6

3 Appendix A Technical specifications ··············································· 3-1

4 Appendix B Ports and LEDs·························································· 4-1

Ports ···································································································································· 4-1

LEDs···································································································································· 4-2

1-1

1 Preparing for installation

Safety recommendations

WARNING!

Only qualified personnel can install and remove the AP and its accessories. You must read all

safety instructions carefully before working with the AP.

To avoid possible bodily injury and equipment damage, read the following safety recommendations

before installing the AP. Note that the recommendations do not cover every possible hazardous

condition.

•Take adequate safety measures to avoid bodily injury and device damage.

•Place the AP in a dry and flat location and take anti-slip measures.

•Keep the AP clean and dust-free.

•Do not place the AP in a moist area and avoid liquid intrusion.

•Keep the AP and installation tools away from walkways.

Site preparation

Before installing the AP, examine the installation site and make sure the AP will operate in a

favorable environment. Make sure the temperate and humidity at the installation site meet the

requirements in Table1-1.

Table1-1 Temperature and humidity requirements

Item Specification

Operating temperature –10°C to +55°C (14°F to 131°F)

Storage temperature –40°C to +70°C (–40°F to +158°F)

Operating humidity 5% RH to 95% RH, noncondensing

Installation accessories

Figure1-1 Accessories provided with the AP

1-2

Installation tools

When installing the AP, you might need the following tools. Prepare the installation tools yourself as

required.

Figure1-2 Installation tools

2-1

2 Installing the AP

Installation flowchart

Figure2-1 Installation flowchart

Pre-installation tasks

Before installing the AP, perform the following tasks:

•Connect the AP to a power source and the network. Examine the LEDs to verify that the AP is

operating correctly. For information about AP LEDs, see "LEDs."

•Record the MAC address and serial number at the rear of the AP for future use.

•Make sure you have completed cabling at the installation site.

Determining the installation position

Determine the installation position by observing the following principles:

•Few obstacles such as wall exist between the AP and clients.

•The AP is far away from electronic devices (such as microwave oven) that might generate

radio frequency (RF) noise.

•The AP does not hinder people’s daily work and life.

2-2

•The place is not water seeping, water soaking, or condensing.

Mounting the AP

The AP can be installed only indoors. You can mount the AP on a wall or a ceiling.

Mounting the AP on a wall

1. Place the mounting bracket against the wall and mark the installation holes on the wall.

Figure2-2 Marking the installation holes on the wall

2. Drill holes with a diameter of 6 mm (0.24 in) and a depth of 30 mm (1.18 in) at the marked

locations, as shown in Figure2-3.

Figure2-3 Drilling holes in the wall

3. Insert a screw anchor into each hole, and tap the screw anchor with a rubber hammer until it is

all flush with the wall surface, as shown in Figure2-4.

2-3

Figure2-4 Hammering the screw anchor into the wall

4. Insert the screws through the installation holes in the wall bracket into the holes in the wall.

Fasten the screws to secure the mounting bracket to the wall.

Figure2-5 Attaching the mounting bracket to the wall

5. Position the four pegs on the AP into the keyhole slots in the mounting bracket and then slide

the AP down until it clicks into place, as shown in Figure2-6.

Figure2-6 Attaching the AP to the mounting bracket

2-4

Mounting the AP on a ceiling

CAUTION:

The ceiling for installing the AP must be less than 18 mm (0.71 in) in thickness, and can bear a load

of 5 kg (11.02 lb). If you must install the AP on a ceiling not strong enough, use boards to reinforce

the ceiling.

To mount the AP on a ceiling:

1. Remove the ceiling tile.

2. Place the mounting bracket against the ceiling tile and mark the installation holes on the ceiling

tile.Drill three holes with a diameter of 6 mm (0.24 in) at the marked positions, as shown

in Figure2-7.

Figure2-7 Drilling holes in the ceiling tile

3. Thread the pan-head screws through the installation holes in the mounting bracket and into the

holes in the ceiling tile. Fasten washers and nuts at the other side of the ceiling to secure the

mounting bracket to the ceiling, as shown in Figure2-8.

Figure2-8 Attaching the mounting bracket to the ceiling

4. Position the four pegs on the AP into the keyhole slots in the mounting bracket and slide the

AP until it clicks into place, as shown in Figure2-9.

2-5

Figure2-9 Attaching the AP to the mounting bracket

5. Verify that the AP is securely installed to prevent it from falling off.

Connecting the AP to a power source

IMPORTANT:

The cable cover is not required in the following conditions:

•Shielded network cables are used to connect Ethernet ports on the AP.

•A power adapter with a straight connector is used to supply power to the AP.

You can supply power to the AP by using a local power source or through 802.3af/802.at PoE as

required. Before powering the AP, make sure the power source (the local power source or the PSE)

is reliably grounded.

Connecting a PoE power source

CAUTION:

The AP is to be connected only to PoE networks without routing to the outside plant.

To power the AP through PoE, use an Ethernet cable to connect an Ethernet port on a PoE switch to

the 5GE/PoE+ port on the AP. After connecting all cables to the AP, attach the cable cover securely

to the AP.

Figure2-10 Powering the AP through PoE

2-6

Connecting a local power source

You can use an AC/DC power adapter to connect the AP to a local power source. No power adapter

is provided with the AP. Prepare one yourself as required. Table2-1 describes the power adapter

specifications.

Table2-1 Power adapter specifications

Item Specification

Input 100 VAC to 240 VAC

Output +54 VDC at 0.74 A

Figure2-11 Using a power adapter to connect the AP to a local power source

Check after power-on

Examine the LEDs on the AP after you power on it to verify that the AP is operating correctly. For

more information about AP LEDs, see "LEDs."

Connecting the AP to the network

All AP settings are configured on the AC. To verify the network connectivity of the AP, execute the

display wlan ap all command on the AC. If the AP status is R/M, the AP has been connected

to the network.

<Sysname> display wlan ap all

Total number of APs: 1

Total number of connected APs: 1

Total number of connected manual APs: 1

Total number of connected auto APs: 0

Total number of connected common APs: 1

Total number of connected WTUs: 0

Total number of inside APs: 0

Maximum supported APs: 3072

Remaining APs: 3071

Total AP licenses: 128

Remaining AP licenses: 127

AP information

State : I = Idle, J = Join, JA = JoinAck, IL = ImageLoad

C = Config, DC = DataCheck, R = Run M = Master, B = Backup

AP name APID State Model Serial ID

2-7

ap1 1 R WA6622 219801A24H8192E00021

Inhaltsverzeichnis

Andere H3C Drahtloser Zugangspunkt Handbücher

H3C

H3C WA6620X Bedienungsanleitung

H3C

H3C WA5510E-T Bedienungs- und Wartungshandbuch

H3C

H3C WA5320 Bedienungsanleitung

H3C

H3C AR 18-3XE/18-21X Series Bedienungsanleitung

H3C

H3C WA6020 Bedienungsanleitung

H3C

H3C WA2600 Series Bedienungsanleitung

H3C

H3C WA4320-ACN-PI Bedienungsanleitung

H3C

H3C WA2620-AGN Bedienungsanleitung

H3C

H3C WA5530i Bedienungsanleitung

H3C

H3C UAP380 Bedienungsanleitung

H3C

H3C WA6120H Bedienungsanleitung

H3C

H3C WA4320H-ACN Benutzerhandbuch

H3C

H3C WA510H Bedienungsanleitung

H3C

H3C WA536 Bedienungsanleitung

H3C

H3C WA2200 Series Bedienungsanleitung

H3C

H3C WA2620i-AGN Bedienungsanleitung

H3C

H3C WA6600 Series Bedienungsanleitung

H3C

H3C WA4320H-ACN Bedienungsanleitung

H3C

H3C WA4320i-ACN Bedienungsanleitung

H3C

H3C WA6500 Series Benutzerhandbuch

H3C

H3C WA2110-AG Bedienerhandbuch

H3C

H3C WA6528X-E Bedienungsanleitung

H3C

H3C WA6630X Bedienungsanleitung

H3C

H3C WA4320-ACN Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung