Hagie UpFront STS 12 Combo Bedienungsanleitung

CALIFORNIA

Proposition 65 Warning

WARNING: Diesel engine exhaust and

some of its constituents are known to the

State of California to cause cancer and

birth defects or other reproductive harm.

WARNING: Battery posts, terminals, and

related accessories contain lead and lead

compounds, chemicals known to the State

of California to cause cancer and birth

defects or other reproductive harm.

ANY PICTURES CONTAINED WITHIN THIS OPERATOR’S

MANUAL THAT DEPICT SITUATIONS WITH SHIELDS, GUARDS,

RAILS, OR LIDS REMOVED ARE FOR DEMONSTRATION

PURPOSES ONLY. HAGIE MANUFACTURING COMPANY

STRONGLY URGES THE OPERATOR TO KEEP ALL SHIELDS

AND SAFETY DEVICES IN PLACE AT ALL TIMES.

HAGIE MANUFACTURING COMPANY

OPERATOR’S MANUAL

FOR

HAGIE MODEL STS 12 HI-TRACTOR

SPRAYER– DETASSELER

07-08 493451

02-09

721 CENTRAL AVENUE WEST

BOX 273

CLARION, IOWA 50525 (515) 532-2861

COVERS MACHINE SERIAL NUMBERS:U1650990001 thru U1650990100

ABBREVIATIONS

A/C........................................................... AIR CONDITIONING

ACCUM..........................................................ACCUMULATOR

ADJ ............................................................................. ADJUST

ADPTR..................................................................... ADAPTER

ALT ................................................................... ALTERNATOR

AMP ........................................................................... AMPERE

APPROX ..................................................... APPROXIMATELY

ASSY .....................................................................ASSEMBLY

AUX.........................................................................AUXILIARY

BRKT ....................................................................... BRACKET

BTTRY ......................................................................BATTERY

C ................................................................................CELSIUS

CAL................................................................... CALIBRATION

CCA ..................................................COLD CRANKING AMPS

CHEM .....................................................................CHEMICAL

cm ...................................................................... CENTIMETER

CTRL........................................................................CONTROL

CYL......................................................................... CYLINDER

DIA........................................................................... DIAGRAM

DIM .......................................................................DIMENSION

DISPL.............................................................DISPLACEMENT

EA ................................................................................... EACH

ELECT .................................................................... ELECTRIC

F......................................................................... FAHRENHEIT

FIG...............................................................................FIGURE

FLO.................................................................................FLOW

FRT...............................................................................FRONT

FT....................................................................FOOT OR FEET

GA................................................................................ GAUGE

GAL.............................................................................GALLON

GPA ...................................................... GALLONS PER ACRE

GPM...................................................GALLONS PER MINUTE

GPS ................................ GLOBAL POSITIONING SATELLITE

HAL..........................................................................HALOGEN

HR...................................................................................HOUR

HYD ......................................................................HYDRAULIC

HYDRO ............................................................HYDROSTATIC

ID ............................................................... INSIDE DIAMETER

IN ..................................................................................... INCH

INFO ................................................................ INFORMATION

Km/H ...............................................KILOMETERS PER HOUR

L....................................................... LITER (DISPLACEMENT)

l ........................................................................LITER (LIQUID)

LB ................................................................................ POUND

LS ...................................................................LIGHT SENSOR

m...................................................................................METER

MAINT............................................................. MAINTENANCE

MIN ............................................................................. MINUTE

M/F.......................................................................MAINFRAME

MPH ............................................................MILES PER HOUR

MT................................................................................ MOUNT

MTH .............................................................................MONTH

MTR .............................................................................MOTOR

NO..............................................................................NUMBER

OD.......................................................... OUTSIDE DIAMETER

PLT ................................................................................PLATE

POLY ............................................................POLYETHYLENE

PRESS.................................................................. PRESSURE

PRKNG ..................................................................... PARKING

PSI ........................................... POUNDS PER SQUARE INCH

QT.................................................................................QUART

RAD ........................................................................RADIATOR

REC ..............................................................RECOMMENDED

REQ ....................................................................... REQUIRED

RPM .......................................... REVOLUTIONS PER MINUTE

SAE............................ SOCIET of AUTOMOTIVE ENGINEERS

SEC............................................................................SECOND

SERV ........................................................................ SERVICE

SLCTR ...................................................................SELECTOR

SMV ................................................ SLOW MOVING VEHICLE

SOLE ......................................................................SOLENOID

SOLU ......................................................................SOLUTION

SPEC .............................................................SPECIFICATION

STRG ......................................................................STEERING

SQ.............................................................................. SQUARE

TACH ............................................................... TACHOMETER

TEMP ............................................................. TEMPERATURE

TERM...................................................................... TERMINAL

TRD...............................................................................TREAD

TT.......................................................................... TUBE-TYPE

TU .......................................................................... TUBELESS

VAR..........................................................................VARIABLE

V.......................................................................................VOLT

VFC............................................ VARIABLE FLOW CONTROL

VLV ............................................................................... VALVE

W/.....................................................................................WITH

W/O.......................................................................... WITHOUT

W.................................................................................WEIGHT

WD....................................................................WHEEL DRIVE

WHL ............................................................................. WHEEL

WK ................................................................................. WEEK

WLD ......................................................................WELDMENT

TO THE OWNER

Congratulations on your selection of a Hagie Model STS 12 SPRAYER/

DETASSELER. We recommend that you study this Operator’s Manual and become

acquainted with the adjustments and operating procedures before attempting to operate

your new sprayer. As with any piece of equipment, certain operating procedures,

service, and maintenance are required to keep it in top running condition.

We have attempted herein to cover all of the adjustments required to fit varying

conditions. However, there may be times when special care must be considered.

Hagie Manufacturing Company reserves the right to make changes in the design and

material of any subsequent sprayer without obligation to existing units.

We thank you for choosing a Hagie sprayer and assure you of our continued interest

in its satisfactory operation for you. If we might be of assistance to you, please call us.

We are proud to have you as a customer.

A WORD FROM HAGIE MANUFACTURING COMPANY

The following pages and illustrations will help

you operate and service your new sprayer. It is the

responsibility of the user to read the Operator’s

Manual and comply with the safe correct operating

procedures and lubricate and maintain the product

according to the maintenance schedule.

The user is responsible for inspecting the

machine and having parts repaired or replaced

when continued use of the product causes damage

or excessive wear to other parts.

Keep this manual in a convenient place for

easy reference when problems arise. This manual

is considered a permanent fixture with this

machine. In the event of resale, this manual should

accompany the sprayer. If you do not understand

any part of the manual or require additional

information or service, contact the Hagie Customer

Support Department:

Hagie Manufacturing Company

721 Central Avenue West

Box 273

Clarion, IA 50525-0273

(515) 532-2861

TO THE OPERATOR

The following symbols, found throughout this manual, alert you to potentially dangerous conditions to

the operator, service personnel, or the equipment.

This symbol indicates a hazardous situation which, if not

avoided, will result in death or serious

injury

This

symbol indicates a potentially hazardous situation

which, if not avoided, could result in death or injury.

This symbol indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury. It may also be used to alert against unsafe

practices.

Most accidents occur as the result of failure to

follow simple and fundamental safety rules. For this

reason, most accidents can be prevented by

recognizing the real cause and doing something

about it before the accident occurs.

Many conditions cannot be completely

safeguarded against without interfering with

efficient operation and/or reasonable accessibility.

Therefore, you must study this Operator’s Manual

SAFETY PRECAUTIONS

and learn how to use the sprayer controls for safe

operation. Likewise, do not let anyone operate

without instruction.

Do not make modifications such as

weldments, add-ons, adaptations, or changes from

the original design of sprayer. Such changes and/

or modifications may become safety hazards to

you and to others and will void all warranties.

SAFETY/ DECALS

I. SAFETY/DECALS

DRIVING

• Before moving sprayer, make sure no persons or obstructions are in path of travel.

• Do not permit passengers on sprayer when it is moving; they may fall off or obstruct operator’s

view.

• Never drive near ditches, embankments, holes, mounds, or other obstacles.

• Never drive on hills too steep for safe operation.

• Always drive at a reasonable field speed.

• Reduce sprayer’s speed before turning.

• Come to a complete stop before reversing direction.

• Pull over to side of road before stopping.

• Additional weight caused from partially full or full solution tanks may cause erratic or increased

stopping distance.

• Never operate sprayer on roadway with any solution in solution tank.

• Do not activate parking brake while machine is in motion or damage may occur to machine.

• Use flashing/hazard warning lights when traveling on public roads, day or night, unless

prohibited by local law.

• Make sure SMV and SIS emblem is in place and visible from rear when traveling on public

roads.

OPERATING

TREAD WIDTH

• Select a tread setting to fit between crop rows.

SPRAYER BOOMS

• Cradle booms when leaving sprayer unattended.

• Make sure booms are folded when cradled.

• Select a safe area before unfolding booms. Avoid power lines and overhead

structures.

OUTRIGGERS

• Make sure the outriggers are locked when folded in or folded out.

GENERAL OPERATION SAFETY

• Do not adjust factory engine RPM settings.

• Operate engine at one bump to assure proper charge pressure for brakes to work

properly.

• Start engine from operator’s seat only. Do not by-pass safety-start switch.

• Never use starting fluid to assist engine start up.

• Never run sprayer engine in a closed building. Proper exhaust ventilation is required.

• If equipped with ground speed sensing radar or light sensing depth units, do not look

directly into radar beam. It emits a very low intensity microwave signal which may

cause possible eye damage.

• Never allow walking personnel in the same field as a detasseler or sprayer.

I. SAFETY/DECALS

SAFETY/ DECALS

REPAIR/MAINTENANCE

HYDRAULICS

• Use caution when working with hydraulic fluid under pressure. Escaping hydraulic

fluid can have sufficient force to penetrate your skin, causing serious injury. This

fluid may also be hot enough to burn.

• Always lower load or relieve hydraulic pressure before repairing a hydraulic oil leak.

• Avoid torching, welding, and soldering near pressurized hydraulic lines.

FUELING

• Always turn engine off and allow it to cool before refueling.

• Do not smoke while refueling.

• Do not fill fuel tank completely. Fuel may expand and run over.

GENERAL REPAIR/MAINTENANCE

• Turn off engine before checking, adjusting, repairing, lubricating, or cleaning any

part of sprayer.

• When servicing radiator, let engine cool before removing pressurized cap.

• Disconnect battery ground cable and turn main battery switch off before servicing

electrical system or welding on machine.

• When charging battery, connect positive cable to positive terminal and negative

cable to negative terminal. Failure to do so may result in an explosion and cause

injury. Likewise, avoid battery acid contact with body.

I. SAFETY/DECALS

SAFETY/ DECALS

CHEMICAL HANDLING

• Never allow chemicals to come in contact with skin or eyes. Wear protective clothing

or respirators as recommended by chemical manufacturer. Store this clothing

outside of the cab so as not to contaminate filtered cab environment. Also, clean

your boots to remove soil or other contaminated particles prior to entering cab.

• Never pour chemicals into an empty tank, fill tank half full of water first.

• Follow chemical manufacturer’s instructions for mixing chemicals.

• Dispose of empty chemical containers properly.

• Wash spilled chemicals or spray residue from sprayer to prevent corrosion and

deterioration.

• Select a safe area to fill, flush, calibrate, and clean sprayer where chemicals will not

drift or run off to contaminate people, animals, vegetation, or water supply.

• Never place nozzle tips or other parts to one’s lips in an attempt to unclog spray tip.

• Do not spray when wind is in excess of chemical manufacturer’s recommended

speed.

• Store pesticides in their original containers with label intact. Keep them in a

separate, locked building.

I. SAFETY/DECALS

GENERAL SAFETY

• Keep a fire extinguisher close at all times.

• Keep all shields in place.

• Keep clear of all moving parts and keep others away when operating.

• Do not wear loose fitting clothing that may be blown or drawn into moving parts.

SAFETY/ DECALS

I. SAFETY/ DECALS

SAFETY/ DECALS

WARNING DECALS

Decals warning you of avoidable danger are

located on various parts of the sprayer. They are

there for your personal safety and protection. DO

NOT remove them. They will fracture upon at-

tempted removal and therefore must be replaced.

Following are locations of important safety de-

cals. Replace them if they are torn or missing. All

warning decals and other instructional Hagie decals

or machine striping may be purchased through Hagie

Customer Support Department. To replace decals,

be sure the installation area is clean and dry; decide

on exact position before you remove the backing

paper.

DECAL LOCATION

Rear of mainframe above booster terminals.

On engine compartment, in front of air intake.

650118

650107

Andere Hagie Traktorzubehör Handbücher

Hagie

Hagie UpFront 120 Bedienungsanleitung

Beliebte Traktorzubehör Handbücher anderer Marken

Land Pride

Land Pride SGC0548 Bedienungsanleitung

Swisher

Swisher Versa Commercial Pro VSP50 Bedienungsanleitung

matev

matev FPS-FKH-Kioti CX 2510 Bedienungsanleitung

matev

matev SCA-130 Bedienungsanleitung

Toro

Toro 08733 Bedienungsanleitung

Avantco

Avantco A425119 Bedienungsanleitung

FTS

FTS G-FTL Series Bedienungsanleitung

Sami

Sami 150-50 Bedienungsanleitung

CAMSO

CAMSO TTS 30 Series Bedienungsanleitung

Luda

Luda tractorCam S Bedienungsanleitung

HLA

HLA BALE KNIFE Series Bedienungsanleitung

P.Lindberg

P.Lindberg 9059890 Betriebsanleitung

Ventrac

Ventrac KD482 Bedienungsanleitung

Original Tractor Cabs

Original Tractor Cabs 4421381 Datenblatt

Grouser Products

Grouser Products 760 Bedienungsanleitung

Degelman

Degelman Landroller Programmierhandbuch

Bush Hog

Bush Hog BS1 Series Bedienungsanleitung

MX MX A104 Bedienungsanleitung