Haier HA1000 Bedienungsanleitung
HA1000\HM1000
Automatic Drum Washing Machine
Table of Contents
Before using
Names of Parts--------------inside front cover
Matters Needing Attention--------------------1-3
Installation----------------------------------------4-5
Control Panel---------------------------------------6
Operational Functions------------------------6-7
During using
Program Selection--------------------------------8
Preparation-----------------------------------------9
Washing Methods---------------------------10-11
Maintenance
Maintenance -------------------------------------12
Trouble Shooting--------------------------------13
Technical Specification-------------------------14
Names of Parts
Drainage hose clip
Back plate
Earth terminal
Power supply cable
Back plate screw (3) Packing bolt (3)
Caution and Warning symbols
For your safety and to prevent damages to the washing machine,
any instructions in this manual with this “Stop” sign shall be
strictly followed.
For your safety, any instructions in this manual with this “Warning”
sign shall be strictly followed.
This diagram may vary slightly with the layout of the washing machine you have just purchased due
to technical improvements.
Drainage hose
Detergent distributor Top
program knob
Operation button
Door
Porthole
Temperature knob
1
Matters Needing Attention
1. A separate earthed socket is required for the
power supply. After installation of the washing
machine,the power plug should be accessible
during the normal wash.
3. Fuses in the power circuit should be rated
for 15A. Refer to a washing machine techni-
cian or a Haier designated service point for
power cable replacement.
5. Do not use flammable detergent or dry clean-
ing agent; do not use flammable spray in close
vicinity to the washing machine; do not remove
or insert the plug in the presence of flammable
gas.
2. Hold the plug and not the electric cable when
unplugging the washing machine.
4. For your safety, dry hands before touching
the washing machine and wear appropriate
footwear .
6. The door of the washing machine will be-
come hot during the water heating process.
Avoid contact with the door during the heating
process. For safety, keep children away from
the washing machine.
7. Do not allow children play with the packing materials after unpacking.
•Safety
2
Matters Needing Attention
9. The washing machine should be place in
a well ventilated area maintaing a space
between walls or furniture.
10. Keep away from heat sources and direct
sunlight to prevent plastic and rubber com-
ponents from aging.
8. The washing machine must not be used in
the open or in area of high moisture as water
droplets may form on electrical components,
Air dry the appliance if the washing machine
components become wet.
1. Make sure that the washing machine is se-
curely connected to the water supply,take the
necessory precautions or con-tact the local
service center if the con-nection is poor or there
is a water leakage.
2. After turning the power off, turn the program
knob clockwise to set washing program.
11. During installation, ensure that the elec-
tric cable is not trapped by the washing ma-
chine and avoid damage to the electric
cable.
•Use
3
Matters Needing Attention
9. Keep the door slightly open when the washing machine is not being used. Never cover
the machine with a plastic sheet.
4. Do not wash foam rubber or similar
sponge materials.
5. Before washing, do up zippers, buttons ,laces
and repair damaged areas,underwear or small
articals should be placed in the laundry bag
or a pillowslip.
Do not wash clothes containing wire frames.
6. Do not open the detergent box during
the wash cycle.
7. The door is fitted with a self-lock device
and will not open until 2~3 minutes after
the washing machine stops. Do not force
the door open. Do not open the door when
water level reaches the port hole.
8. After washing, turn off the tap to prevent
leakage; unplug the washing machine and
wipe clean the lower part of the port hole.
3. Never place heavy objects ,a heating
applianceor a water container on the top
panel of the washing machine.
Installation
4
Fig 1
•As shown in figure1 remove all the packing materials
(including the foam base).
•Remove the packing screws as shown in figure 2.
The packing bolts protect the appliance from shock during
transportation The steps below should be followed before
using the appliance,
1. Remove the rear panel of the washing machine;
2. Remove the three packing bolts from the rear panel of the
washing machine,the rubber hose and then the shock ab-
sorption channel steel;
3. Reinstall the back plate;
4. Fill the holes left by the packing bolts with plastic plugs.
(Attention: the packing bolts and rubber hose should be kept
in a safe place for later use)
Fig 2
•Adjusting the position of the washing machine .There are
adjustable feet under the bottom of the washing machine. Be-
fore use, the washing machine should be adjusted, as shown in
figure 3, so that it is level.
Fig 3
5
Installation
Connection of water inlet hose and washing machine
1. Place the water inlet hose nut on the connector
of the water inlet valve.And rotate it clockwise to
screw onto the connector
2. slightly shake the water inlet hose nut to see if
it is tightly and properly fixed.
connector of water inlet valve
water inlet hose nut
Water drainage hose
•The height of the terminal of the water drainage hose should
be between 80cm-100cm, the water drainage hose must be
securely placed on the clip on the back of the washing machine.
•Use the water drainage support supplied as an accessory
for proper installation of the water drainage hose .fix the water
drainage hose support with waterproof sring.Do not use an
excessively long water drainage hose and contact the autho-
rized technician if the water drainage hose needs to be
extended.the water drainage hose should not be extended
more than250cm.(longer extension will result in concurrent
water inflow and outflow).The diameter of the extension hose
should be the same as the original hose.
caution:water drainage hose must not be immersed in water.
the original and extension hoses should be tightly connected .
Connection of power supply
Check the following items before connection to the power supply.
•The socket conforms to the maximun power load(The maximum current load of the
socket and power supply cable should not be less than 15A).
•Power supply voltage conforms to the required value.
•
The power supply socket and the plug of the washing machine are compatible,if they are not
compatible ,Refer to a washing machine technician or a Haier designated service point
for power cable replacement.The washing machine should be connected to an earth
before use.
•Supplementary earth cable should not be necessary if the socket is connected to the
earth.
•Supplementary earth cable should be installed on the upper back of the washing
machine andconnected to an earth if the power supply socket has no earth connection.
80cm
100cm
•
•
••
6
Control Panel
A Washing program
Turn the knob clockwise to set the desired wash program .
Caution: Turn off the power and turn the program knob clockwise
for setting desired wash program.
B Washing temperature
Turn the knob clockwise to set the desired temperature.
Temperatures between 30OC-90OC can be setted , Cold wash is se-
lected when the knob is set at *.
HA\HM1000
80
80
C Detergent Dispenser.
The detergent dispenser is divided into 3 compartments marked 2,A,C
2 Wash detergent⧊Except liquid detergent⧋
A Softeners, conditioners, perfumes
C Bleach
7
Operational Functions
G Power light
The light will illuminate when the power supply is connected.
F Power button
Press the button ,washing machine will start working;release the button,
the washing machine will stop.
ON
OFF
E No spin button
When this button is pressed, the spin cycle will be spared but water
drain is still available. This function is useful for hard ironing fabrics,
such as chemical fiber and wool fabrics.
D Cold Wash BUtton.
Press it you need a cold wash.
Release it you need a heating wash.
For cotton, water. can be heated to 90 •.
For synthetic, to 60•and for wool, to 40•.
H Door Lock Light
Remember that only when the washer doesn’t work, we can open the
door. After the washing program finish,after 3 minutes, when the self-lock
meter turn off, we can open the door.
8
Program Selection
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Haier Waschmaschine Handbücher
Haier
Haier XPB40-23S Bedienungsanleitung
Haier
Haier HWF75AW1 Bedienungsanleitung
Haier
Haier HW-B1070 Bedienungsanleitung
Haier
Haier HWM80-113S Bedienungsanleitung
Haier
Haier HWM60-15P Bedienungsanleitung
Haier
Haier HLP23E - Electronic Touch Pulsator Ing Portable Washing... Bedienungsanleitung
Haier
Haier HW07-CP1439 Bedienungsanleitung
Haier
Haier HWM100-1701R Bedienungsanleitung
Haier
Haier HWM60-AC Bedienungsanleitung
Haier
Haier HW80-B14939S8 Bedienungsanleitung
Haier
Haier HWF5300AW Bedienungsanleitung
Haier
Haier XQJ60-31 Bedienungsanleitung
Haier
Haier HWM120-01A6 Bedienungsanleitung
Haier
Haier HG1000TXVE Bedienungsanleitung
Haier
Haier HL1400TXV Bedienungsanleitung
Haier
Haier HW80-BD1626 Bedienungsanleitung
Haier
Haier HWM70-1708T Bedienungsanleitung
Haier
Haier HW80-BP1439N Bedienungsanleitung
Haier
Haier HWM 80-AS Bedienungsanleitung
Haier
Haier HWD 105-B14959S8U1 Bedienungsanleitung
