HAKO 7092.65 Bedienungsanleitung

Assembly Manual

LED working light (7092.65)

Foreword

The installation procedures described

in this assembly manual should only be

undertaken by a Hako service centre or

a workshop authorised by Hako. Mem-

bers of staff with the required level of

training and expertise are only guaran-

teed in the said workshops.

This assembly manual may be used

only in conjunction with the instruction

manual of the machine.

Safety instructions

Please observe the general safety reg-

ulations of the corresponding machine

in the relevant operating manual.

Place the machine on a level surface

and secure it with the parking brake.

Switch the machine off and pull out the

key.

We would expressly advise you that no

legal claims may be asserted based on

the contents of this manual. In the case

of necessary repair work, please make

sure that only original spare parts are

used. Only original spare parts guaran-

tee constant and reliable operational

readiness of your machine. We reserve

the right to make changes in the inter-

ests of further technical development.

Valid as from: September 2017

Hako GmbH

23843 Bad Oldesloe, Germany

Hamburger Str. 209-239

Phone +49 4531 806-0

Introduction

LED working light

1 LED working light

1.1 Parts list

1 1x LED working light compl.

2 1x corrugated hose holder

1.2 Before installation

1. Place the machine on a level surface

and turn it off.

2. Remove floor mat in footwell.

3. Remove brake button (Fig. 1/3)

Fig. 1

LED working light

1.3 Installing the working light

The working light is installed on the left

next to the front wheel (Fig. 2/1).

1. Fit working light to holder of chassis

(Fig. 2/2).

2. Insert corrugated hose holder into

existing hole (Fig. 2/3).

3. Secure cable of working light to cor-

rugated hose holder in such a way

that it is free of tension.

4. Lead cable through floor opening

into the interior (Fig. 2/4).

5. Connect plug of working light to

2-pin connector E01 of cable

loom W 3 (Fig. 2/5).

1.4 Adjusting the working light

Align working light so that it is straight-

ahead in the direction of travel.

Set tilt angle to approx 5° (Fig. 2/6).

Fig. 2

5°

LED working light

1.5 Setting in the configuration

The LED working light option must be

activated via the configuration menu.

Requirements:

• Batteries inserted

• 4-digit code or diagnosis plug

97097737 is present.

If diagnosis plug is used:

Connect diagnosis plug to slot X20 of

controller A1 (Fig. 4/1).

Setting:

1. Turn on the machine.

2. Select the arrow softkey (Fig. 3/3) on

the control panel using the turn-push

knob (DDS) (Fig. 3/2) and press to

access the sub-menu.

3. Select the configuration menu in the

sub-menu (Fig. 3/4).

Fig. 3

4. Enter the 4-digit code in the configu-

ration menu at the top (Fig. 3/5):

- Rotate the DDS until the required

field is reached.

- Press DDS, then rotate to adjust

the value.

- Press again to save the value.

Alternatively, use the diagnosis plug!

5. Select the value of the option under

(Fig. 3/6) in the configuration menu

and save by pressing the DDS. After

confirmation of the final digit, OK?

appears. Press the DDS again to

save the value. The saved value is

now displayed in green.

If the value is not to be saved, exit

the menu using the return button

(Fig. 3/7).

Option Value

LED working light 1. 6. 1.

Advanced Technology for a Cleaner,

Better Environment

Hako GmbH ·Head Office · Hamburger Str. 209-239 ·23843 Bad Oldesloe ·Germany

Phone +49 4531 806-0 ·Fax +49 4531 806-338

88-10-3150 - 3925-00

Andere HAKO Arbeitsleuchte Handbücher

HAKO

HAKO 7091.25 Bedienungsanleitung

Beliebte Arbeitsleuchte Handbücher anderer Marken

ANSMANN

ANSMANN POWERLIGHT 5.1 Bedienungsanleitung

RTRMAX

RTRMAX RTX1868 Bedienungsanleitung

FeinTech

FeinTech LAL00220 Bedienungsanleitung

Bunker Hill Security

Bunker Hill Security 64735 Bedienungsanleitung

Goobay

Goobay 30450 Bedienungsanleitung

REV Ritter

REV Ritter SPOT Bedienungsanleitung

Ignition

Ignition Stagepix Line 100 IP Bedienungsanleitung

SCANGRIP

SCANGRIP DUO CONNECT Bedienungsanleitung

Bosch

Bosch GLI 18 V Bedienungsanleitung

Bayco

Bayco SL-1514 Bedienungsanleitung

EUFAB

EUFAB SMD LED 8+1 Bedienungsanleitung

DeWalt

DeWalt DCL510 Bedienungsanleitung

PowerSmith

PowerSmith PWLD080T Bedienungsanleitung

MaxLite

MaxLite 73683 Bedienungsanleitung

Heitronic

Heitronic Trend 27867 Bedienungsanleitung

Monzana

Monzana Gore MZCL10 Bedienungsanleitung

EINHELL

EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung