Hammerhead HLCL360 Bedienungsanleitung
SELF-LEVELING
360-DEGREE
CROSS LINE LASER
MODEL HLCL360
ATTACH YOUR RECEIPT HERE
Serial Number ______________________ Purchase Date_______________________
Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 1-877-888-1880, 8:30 a.m. – 8:00 p.m.
EST (Monday – Friday) & 10:00 a.m. – 6:00 p.m. EST (Saturday and Sunday).
2 SELF-LEVELING 360-DEGREE CROSS LINE LASER
TABLE OF CONTENTS
Technical Specications ...........................................2
Safety Instructions ...............................................3
Unpacking .....................................................5
Description.....................................................6
Operation ......................................................7
Maintenance...................................................13
Troubleshooting ................................................14
Warranty......................................................15
TECHNICAL SPECIFICATIONS
COMPONENT SPECIFICATIONS
Power supply 6V (4 x 1.5V AA alkaline battery)
Laser λ=635 nm, Class II laser, maximum laser
output<1 mW
Self-leveling range ±4°
Accuracy ±1/8 inch @ 30 feet
Operating range 30 feet (diameter 60 feet)
Operating time Approx. 35 hours
Operating temperature 32°F to 104°F (0°C to 40°C)
Storage temperature 14°F to 158°F (-10°C to 70°C)
*Important: Under unfavorable conditions, such as in bright sunlight or when
targeting poorly reecting or very rough surfaces, the tool’s measuring range and
accuracy will be reduced.
SELF-LEVELING 360-DEGREE CROSS LINE LASER 3
SAFETY INSTRUCTIONS
Safety Instructions for Self-Leveling 360-Degree Cross Line Laser
WARNING
LASER RADIATION. Do not stare into beam. Class
II laser product. Turn the laser beam on only when
using this tool.
• Do not remove or deface any product labels.
• Avoid direct eye exposure. The laser beam can
cause ash blindness.
• Do not operate the tool around children or allow
children to operate the tool.
• Do not place the tool in a position that may
cause anyone to stare at the laser beam,
whether intentionally or unintentionally.
• Do not use on surfaces, such as sheet steel, that have shiny, reective
surfaces. The shiny surface could reect the beam back at the operator.
• Always turn the laser tool off when not in use. Leaving the tool on
increases the risk of someone inadvertently staring into the laser beam.
• Do not attempt to modify the performance of this laser device in any way.
This may result in a dangerous exposure to laser radiation.
• Do not attempt to repair or disassemble the self-leveling 360-degree cross
line laser. If unqualied persons attempt to repair this product, serious injury
may occur. Any repair required on this laser product should be performed only
by qualied service personnel.
• Use of other accessories that have been designed for use, with other laser
tools could result in serious injury.
• Do not place or store tool under extreme temperature conditions.
CAUTION
PRECAUCIÓN
CAUTION
PRECAUCIÓN
MADE IN CHINA SERIAL NO.
SERIE NO.
HECHO EN CHINA
Model/ Modelo : HLCL360
6V 4×1.5 V AA Battery
6V Batería AA 4×1,5 V
Self-Leveling 360-Degree Cross Line Laser
Láser autonivelante de líneas cruzadas de 360 grados
AVOID EXPOSURE-
EVITE LA EXPOSICIÓN-
Laser radiation is emitted
from this aperture
La radiación láser se emite
de esta abertura
4 SELF-LEVELING 360-DEGREE CROSS LINE LASER
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS
DANGER
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW
THESE INSTRUCTIONS
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more
of the following measures: Reorient or relocate the receiving antenna. Increase the
separation between the equipment and receiver. Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. Consult the dealer or
an experienced radio/TV technician for help.
SELF-LEVELING 360-DEGREE CROSS LINE LASER 5
SAFETY INSTRUCTIONS
DANGER
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of the
pacemaker.
UNPACKING
When unpacking the box, do not discard any packing materials until all of the
contents are accounted for:
a. Open the carton to locate the following:
• Self-leveling 360-degree cross line laser
• 4 X AA alkaline batteries
• Soft bag
• Operator’s manual
b. Carefully lift the cross line laser out of the carton and place it on a
stable, flat surface.
6 SELF-LEVELING 360-DEGREE CROSS LINE LASER
DESCRIPTION
KNOW YOUR SELF-LEVELING 360-DEGREE CROSS LINE LASER
This self-leveling 360-degree cross line laser is highly versatile. It can be
hand-held, leveled on a horizontal surface or mounted on a tripod (available
separately).
1
23
4
5
PARTS DESCRIPTION
1Mode button
2Leveling LED indicator
3Hand receiver LED indicator
4Power switch
5Laser apertures
65/8" threaded mounting hole
7Battery compartment
7 6
SELF-LEVELING 360-DEGREE CROSS LINE LASER 7
OPERATION
1. TO INSTALL BATTERIES
The battery compartment holds four
“AA” batteries.
a. Push the latch to open the
battery cover.
b. Insert four new “AA” alkaline
batteries, following the polarity
(+/-) as indicated on the inner of
the compartment.
c. Securely close the cover.
NOTE:
• Always turn off the tool before installing or replacing the batteries.
• Remove the batteries from the tool when not using it for extended periods.
• The 4 AA batteries should match each other in brand and type.
• Do not mix old and new batteries.
• Remove depleted batteries immediately, and dispose of them according to the
laws and regulations governing your community.
1
8 SELF-LEVELING 360-DEGREE CROSS LINE LASER
OPERATION
2. TO TURN THE SELF-LEVELING
360-DEGREE CROSS LINE
LASER ON AND OFF
The power switch is located on the
side of the tool.
a. To turn the self-leveling
360-degree cross line laser on,
push the power switch in the
direction of the “ON” arrow.
WARNING
When turning on the self-leveling 360-degree cross line laser, always be aware
of protecting your eyes and the eyes of those around you. Never point the self-
leveling 360-degree cross line laser at anyone’s face, including your own.
b. To turn the tool off, slide the switch in the direction of the “OFF” arrow.
ON
OFF
2
SELF-LEVELING 360-DEGREE CROSS LINE LASER 9
OPERATION
3. LASER LINE PROJECTION
MODES
Your self-leveling 360-degree cross
line laser has three laser-projection
modes. To select a specic laser-
projection mode, press the mode
button until you reach the desired
projection mode. This laser tool
defaults to the cross-hair pattern
mode when it is turned on.
To choose a projection mode, press
the mode button:
a. Press the button once to select the horizontal laser line.
b. Press the button twice to select the vertical laser line.
c. Press the button three times to return to the cross-hair pattern (both
horizontal and vertical lines).
3
MODE
BUTTON
10 SELF-LEVELING 360-DEGREE CROSS LINE LASER
OPERATION
4. HAND RECEIVER MODE
When working with the tool
outdoors, the strong sunlight will
make the laser lines hard to be
identied. Switch to hand receiver
mode: the laser lines will now
pulsate with high frequency. When
received by the a laser receiver
(available separately), the laser can
be detected up to 100 ft. away.
To switch to hand receiver mode,
keep the mode button pressed; the
LED indicator will illuminate.
This mode can be used when the tool is in self-leveling or lock mode.
4
HAND RECEIVER
LED INDICATOR
Inhaltsverzeichnis
Sprachen:
Andere Hammerhead Laser-Nivelliergerät Handbücher
Beliebte Laser-Nivelliergerät Handbücher anderer Marken
Nedo
Nedo ET-5 Bedienungsanleitung
geo-FENNEL
geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung
LaserLiner
LaserLiner X2-Laser Bedienungsanleitung
Spectra
Spectra LL300N Bedienungsanleitung
geo-FENNEL
geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung
Nedo
Nedo Crossliner 4 Bedienungsanleitung
