Handol 35T Bedienungsanleitung

INSTRUCTIONS

34T 35T

Installations

WARNING!

During operation some of the stove surfaces become

extremely hot and can cause burn injuries if touched. Be aware

of the strong heat radiated through the hatch glass. Placing

flammable material closer than the safe distance indicated may

cause a fire. Pyre lighting can cause quick gas ignition with the

risk of damage to property and personal injury.

Quality approval

The stove has been tested by the

Swedish National Testing and

Research Institute and meets

the applicable regulations for

CE marking and the stricter

requirements for P marking.

Certificate number for P

Marking: 0112/07

Manufacturer’s assurance

Manufacture of the product

has taken place in accordance

with those documents which are

the basis for the relevant type

approval certification and the

required manufacturing checks.

Requirements for flue

The chimney must be

dimensioned for at least 350° C

for both top connection directly

upwards and connection directly

backwards from the rear of the

stove.

Handöl 30 is a Swan marked

wood burning stove.

As the premier stove

manufacturer in Sweden, we

at Nibe Stoves are committed

to Swan marking our stoves.

Choosing to Swan mark our

products is one aspect of our

vision to be a company of

the future with equally high

quality standards regarding the

environment.

Certification number 378-001.

NOTE! Report installation of a stove to your local authority.

The owner of the house is personally responsible for ensuring

compliance with the mandatory safety requirements and must

have the installation approved by a qualified inspector.

Your local chimney sweep must also be informed about the

installation as this will affect the routines for regular chimney-

sweeping services.

EC declaration of

conformity

Manufacturer

Name NIBE AB/ NIBE Stoves

Address Box 134, Skulptörvägen 10, SE-285 23 MARKARYD

Place of manufacture Markaryd, Sweden

Product covered by this declaration

Product type Stove ﬁred by solid fuel

Type designation Handöl 30-series

Type acc. to standard EN 13240 annex ZA

Intended for use Heating of living accomodation

Fuels Wood logs

Special conditions None

CE-marking

Nominal output: 5 kW

Fuel type: Wood logs

Flue gas temperature: 275° C

Energy eciency: 80%

Emission of CO: 0,05%

Safety measurments for: Distance to adjacent combustible materials:

Handöl 34T

Behind 100 mm, beside 415 mm

Handöl 35T

Behind 100 mm, beside 415 mm

Manufacturing check by approved organisation

Notiﬁed body No. 0402

Name Swedish National Testing and Research Institute AB

Address Box 857, SE-501 15 BORÅS

Appendix

• Lighting and Installation Instructions

Niklas Gunnarsson

Business area manager NIBE Stoves

www.handol.eu

378 001

TABLE OF CONTENTS

General 76

Installation distance to walls and ceiling 77

Supply of combustion air 79

Removing the loose parts 80

Connection to chimney 82

Installing the surround 34T 84

Installing the surround 35T 88

Installing accessories · heat tank 94

DEAR HANDÖL OWNER

We welcome you to the Handöl family and hope that you will

get a great deal of pleasure from your stove. We understand

that you place high demands on both quality and design. As the

new owner of a Handöl stove you have secured a product with

timeless design and long service life.

The stove combustion is also environmentally friendly and

efficient for the best heat production.

Read the installation instructions carefully before you begin

installation and the separate lighting and user instructions

before you light the fire.

General

This manual contains instructions about how the Handöl

30 series must be assembled and installed. To ensure

the function and safety of the stove, we recommend

that the installation is carried out by an authorised

technician. Our Handöl dealers can recommend suitable

technicians,

information about our dealers can be found at

www.handol.eu

Instructions for lighting are also supplied with the stove.

Read them carefully and keep them safe for future use.

The stove is type approved and must be connected to a

chimney dimensioned for at least 350°C, the external

connection diameter is Ø150 mm. Supply air from the

open air should be used as combustion air.

Building application

Before installing a stove or erecting a chimney it

is necessary for you to make a building application

permission to your local authority. Ask your local

authority for advice regarding building regulations and

the application.

Structural support

Check that the wood joists are strong enough to bear

the weight of the stove and chimney. The stove and

chimney can usually be placed on a normal wooden joist

in a single occupancy house if the total weight does not

exceed 400 kg.

Hearth plate

To protect the floor from any embers the stove must be

placed on a hearth plate. If the floor under the stove is

flammable, it must be protected by a non-flammable

material which covers at least 300 mm to the front and

100 mm on each side.

The hearth plate can consist of natural stone, concrete

or 0.7 mm metal. A painted metal or glass hearth plate is

available as an accessory.

Chimney

The stove requires a draft in the chimney of at least –12

Pa. The draft is affected both by the length and area

of the chimney, and by how well sealed it is. Minimum

recommended chimney length is 3,5 m and a suitable

cross section area is 150-200 cm² (140-160 mm in

diameter). Carefully check that the chimney is sealed and

that there is no leakage around soot hatches and flue

connections.

Note that a flue with sharp bends and horizontal routing

reduces the draught in the chimney. Maximum horizontal

flue is 1 m, on the condition that the vertical flue length

is at least 5 m. It must be possible to sweep the full

length of the flue and the soot hatches must be easily

accessible.

Eldstadsbeklädnad

Rosterreglage Asklåda

Förbränningsluftsreglage

Brasbegränsare

HANDÖL

In accordance with standards below

marking was affixed:

European Standard:

SE Quality Certification, P-marked:

NO Standard NS 3059:

DE and AT Standard DIN 18.891 and

Art 15a B-VG:

Type:

Nominal Output:

Fuel:

Minimun draught:

Flue gas temerature:

Energy efficiency:

Emission of CO in cumbustion products:

Distance to cumbustible wall (mm):

Follow the user’s instructions and use only recomended fuel

NIBE AB Box 134 SE-285 23 MARKARYD SWEDEN

2007

EN 13240

Cert no 0112/07

SINTEF 110-0275

RRF-40 07 13 90

Handöl 31/31A/32/32A

5 kW

Wood

12 Pa

280°C

78%

0,14%

Behind 150

Beside 450

Corner 150

HANDÖL

NIBE AB SE-85 21 Markaryd Sweden

Type:

Production no.

50-series

7090300236

Technical specifications

Output 3-7 kW

Nominal output 5 kW

Efficiency up to 80%

Model 34T 35T

Weight (kg) 320 250

Width (mm) 550 550

Depth (mm) 430 430

Height (mm) 1600 1600

Tank stone (kg) 70 70

Connector diameter Ø150 mm ext.

Type approved in accordance with:

European standard EN-13240

Swedish environmental and quality marking, P-marking cert.

no. 0112/07

Norwegian standard NS 3059, SINTEF 110-0275

German standard DIN 18.891, RRF-40 07 13 90

Rating plate

Fire bars

Hearth cladding

Grate control

Combustion air control

Ash-pan

Installation distance to walls and ceiling

550

1600

min 2300

Combustible roof

Air inlet Ø64

120

430

1050

1140

167

Hole in foot plate Ø120

Place the stove on the hearth plate and

check that the installation distances

given in the figures below are followed.

The minimum distance in front of the

stove opening to combustible parts of the

building or interior decoration must be at

least 1 m.

368

150

729

781

Combustible wall

267

100

415

400

300

100

300

200

100

690

Combustible wall

Permitted area for

combustible material

H34T

*To prevent discolouration of painted fire walls, we recommended the same side distance as to combustible walls.

268

629

640

Fire-retardant wall of

brick or concrete

217

50*

325*

Fire-retardant wall of

brick or concrete

When top connecting a steel

flue please refer to the relevant

manufacturer’s installation

instructions. Observe the safety

distances to combustible material

that steel flues require.

Installation distance to walls and ceiling

550

1600

min 2300

Air inlet Ø64

Combustible roof

430

1050

1140

167

120 Hole in foot plate Ø120

Place the stove on the hearth plate and

check that the installation distances

given in the figures below are followed.

The minimum distance in front of the

stove opening to combustible parts of the

building or interior decoration must be at

least 1 m.

368

150

729

781

Combustible wall

267

100

415

400

300

100

300

200

100

690

Combustible wall

Permitted area for

combustible material

H35T

217

50*

325*

Fire-retardant wall of

brick or concrete

268

629

640

Fire-retardant wall of

brick or concrete

When top connecting a steel

flue please refer to the relevant

manufacturer’s installation

instructions. Observe the safety

distances to combustible material

that steel flues require.

*To prevent discolouration of painted fire walls, we recommended the same side distance as to combustible walls.

** 1640 with soapstone top

Supply of combustion

air

Combustion air can be provided directly via a

duct from outside, or indirectly via a vent in the

outer wall of the room where the stove is to be

placed. The amount of combustion air that is

used for combustion is approx. 25 m3/h.

Some installation alternatives are shown to the

right.

The air duct connection on the stove has an

external diameter of Ø64 mm.

In hot areas the duct should be insulated with

30 mm mineral wool covered with a moisture

inhibitor (plastic). It is important that the lead-in

between the pipe and the wall (or floor) is sealed

using jointing compound. When duct routing

for further than 1 m the pipe diameter must be

increased to 100 mm and a correspondingly

larger wall vent must be selected.

A 1 m length of condensation insulated ducting

for combustion air is available as an accessory.

40 mm

Knockout

To insert the combustion air hose, tap out the

knockout from the floor panel or leg using a hammer,

remember to protect the floor.

Unpacking

The insert is secured by four packaging ring angles.

Loosen the screws and remove the angles.

Before the stove is used, it must be inspected by an

authorised chimney sweep.

Read the Instructions for Lighting the Handöl 30

series before lighting the fire for the first time.

Removing the loose parts

Sweeping

When sweeping, the smoke baffle must be lifted out,

on the Handöl 30 series this can be done by lifting the

smoke baffle and removing the side piece. Lift the smoke

baffle out and remove the remaining sections. Handle

the parts with care.

Self-closing hatch

The stove has a spring to close the hatch automatically.

The spring is above the heat deflector. The closing

force of the hatch can be adjusted by moving the spring

between the three notches on the lever. The angle of the

stove also affects the closing force of the spring.

If the spring force seems weak despite

the spring being mounted at the end of

the lever, the angle of the stove should be

checked.

Type plates

Two type plates are supplied with the stove. One for the

insert and one for the surround kit.

Refer to the chimney installation instructions. The

following describes how the chimney system is

connected to the stove.

The stove body is prepared for top connection on

delivery. When connecting from the rear, the cover and

connection must be swapped around.

Top connection to the chimney

When connecting to the top, the whole stove surround

must be installed before installation of the chimney can

begin. Installation of the surrounds for the respective

models is described later on in these installation

instructions.

The start pipe is placed over the connection on the

insert. Make sure that the gasket on the connection is

intact and in position. The stop washer is positioned over

the collar on the start pipe. The cuff must rest against

the top of the stove. Then install the remaining parts of

the chimney. The cuff covers the lower section of the

start pipe and facilitates any service work.

Connection to chimney

Chimney mantle

Cuff

Stop washer

Start pipe

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Handol Herd Handbücher

Handol

Handol H26T/K Tall Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung