Hanover KAMADO Bedienungsanleitung

BARBECUE GRILLS

MANUAL

OWNER’S

KAMADO

WELCOME Page 1

Accessories

Ash Cleaning Tool Secondary Cooking Grid

(Half Grid)

Chimney Top Control

Ceramic Top (dome lid)

Ceramic Base

Cart

Bottom Air Control &

Ash Clean Out

Thermometer

Inside of Grill

Fire Grate

Fire Box

Fire Ring

Oak Shelf

Grill Cover

Congratulations on the purchase of your Hanover Kamado Grill and Smoker!

You now have one of the most versatile cookers available for your BBQ adventures.

PARTS IDENTIFIER Page 2

Left Shelf Bracket

Left Oak Side Shelf Right Oak Side Shelf

Hinge Assembly

Right Shelf Bracket

Handle

Shelf Stop Tab

Shelf Support

10 mm Acorn Nut w/

Flat Head Screw (8) Top & Bottom Bands

H5 Band Tension Bolt w/10mm Nut & Washer

Springs (2) 10mm Acorn Nut w/ Flat

Head Screw

Oak Filler

Oak Handle Retainer

Screws w/ Nuts

Handle Bracket

Shelf Support

Large Phillips head screwdriver, 10 mm wrench (included), 5 mm (3/16”) Allen wrench (included).

Locate the serial number of your grill on the lower base portion of the grill box or on the inside wall of the

grill hinge. Record your serial number for future reference.

Built-in Enclosure Dimensions Please use the following dimensions and guidelines for built-in applications.

It is always best to build a non-combustible enclosure with masonry and/or steel studs and cement board

(Hardiebacker, Wonderboard, Durock, etc.).

It is best to keep your countertops and the area underneath the grill of non-combustible materials. Always

keep the surface of the grill at least 1”away from combustible materials inside the enclosure and 1” at the

counter top.

In a sealed, combustible enclosure make sure there is at least 20 square inches of ventilation at the bottom

and 20 square inches of ventilation at the top of the enclosure. This will provide enough air to cool the

enclosure and feed the re. Note that an open enclosure ensures the best air ow and easy access to the

Bottom Air Control.

22½” Combustible Top

22 “ Non Combustible Top

ASSEMBLY - for Built-in Applications Page 3

Assembly Tools Required

1. If your grill will be on a combustible surface, the Ceramic Feet and Stainless Steel Heat Shield (SSHS)

must be used.

2. Place the Feet and Shield in the position you would like the grill.

3. The Feet should be arranged underneath the Shield with equal spacing between them. One should be

placed directly in the center on the back side of the Shield and the other two on the left and right of the

front side. Fig. 1

4. The ceramic Feet and Heat Shield may be replaced with a non-combustible slab. The slab should be a

solid stone or masonry unit (at least 1¼” thick). The recommended dimensions of the slab are at least 16”

square or round. Fig. 2

Unbox the Grill

Ceramic Feet and Heat Shield

1. Cut and remove the plastic bands from the box.

2. Lift o the top of the box.

3. The sides of the box are individually removable.

4. Open the grill and remove the cooking grid and discard the cardboard.

5. Remove other items from their packaging and set aside: Stainless Steel Heat Shield, Ceramic Feet (3pcs.),

Chimney Top, Handle, Grate and Stainless Steel Eciency Plate.

6. The stainless steel heat shield and ceramic feet are packaged separately and are only provided for

built-in applications (These items are not included if grill is purchased with cart)

ASSEMBLY - for Built-in Applications Page 4

Warning:

If the grill is placed on or near a combustible surface, such as a wood deck, it is the owner’s responsibility to

ensure embers do not escape the grill and ignite the wood. A non-combustible protective pad is recommended

underneath and in front of the lower air control/ash clean out door. 10:00am

Fig.1

Fig.2

Proceed to nal grill assembly on page 6

(Skip assembly for cart application).

Assembly Tools Required

Large Phillips head screwdriver, 10 mm wrench (included), 5 mm (3/16”) Allen wrench (included).

Unbox the Grill

1. Cut and remove the plastic bands from the box.

2. Lift o the top of the box.

3. The sides of the box are individually removable.

4. Open the grill and remove the cooking grid and discard the cardboard.

5. Remove the items in the bottom of the grill and set aside: Stainless Steel Heat Shield, Chimney Top,

Handle, Grate and Stainless Steel Eciency Plate.

6. Unbox cart kit.

7. Unbox shelf kit (optional).

Cart Assembly

8. Remove the bubble wrap from Leg Joiners and the four stainless

steel Cart Legs.

9. Slide the two Leg Joiners into one of the legs that has a locking

castor wheel. Fig.1 The at side of the Joiners should be facing up.

Screw them into place with a Phillips head screw driver.

ASSEMBLY - for Cart Applications Page 5

10. Select one of the stainless steel legs without the locking caster and

slide it onto the Leg Joiner opposite the rst leg. Screw into place

loosely.

11. The remaining two legs may now be attached without regard to their

position. After the legs are all in, place the cart in an upright position

and securely tighten down the screws. Fig. 2

Fig. 2

Fig.1

Warning:

Do not fully tighten any of the screws until completion. Take care that the screws

are going in straight so the threads are not ruined. Be gentle and do not force the

screws. They should turn with very little pressure.

Fig. 1

4. Unpack the Top Dome Handle.

8. For Built-in Application-Place the Stainless Steel Eciency Plate in the

bottom of the rebox with the small leg spacers facing down.

9. Place the ceramic Firebox into the grill so that the Bottom Air Control Port

aligns with the bottom Air Control Door on the grill. Place the Fire Ring on

top of the Firebox with the three notches facing upward and with one of the

notches all the way to the back. Fig. 7

Placing Grill in Cart

6. With assistance, grip the stainless steel hinge and grip inside the bottom air control and lift the grill into

the Cart. The front of the grill should be located between the two legs with locking caster wheels.

Placing Grill in Built-in Enclosure

7. If you are placing the grill into the hole of an enclosure one person should grip the stainless steel hinge

at the rear of the grill. The second person should open the lid and grip the Bottom Air Control from the

inside of the grill. Keep the other hand on the Main Handle. Put the grill into position on the feet or slab.

5. Check the rest of the pre-installed acorn nuts to ensure that they are all tight

(use the 10mm wrench). Fig. 6 If the acorn nuts spin without tightening,

just use a rapid jerking action as you tighten and this usually cause them

to tighten suciently. The pre-installed Band Tension Bolts should also be

checked for tightness.

3. Remove the cardboard pad from the bottom inside of the grill and discard.

2. Remove the packing materials from around the perimeter of the Firebox

and lift it out of the grill. Set it aside. It is easiest to lift it by the holes or the

clean-out port at the bottom. Fig. 4

FINAL GRILL ASSEMBLY Page 6

Fig. 4

Fig. 3

Fig. 7

Fig. 5

Fig. 6

Acorn Nuts

Note:

There are 2 acorn nuts packaged with the handle. Use the acorn nuts to fasten the

handle to the two screws protruding from the stainless steel band on the front of

the grill. Fig. 5

Note:

The Band Tension Bolt may be tightened very securely without fear of damaging the ceramics (usually 2 or 3

revolutions). This ensures that the hinge will be stable and secure and that you may use the hinge or shelf brackets to

lift the grill without incident. Use the 5mm or 3/16 hex key (Allen wrench) to hold the bolt in position. Use the 10mm

wrench to turn the nuts. Do not turn the bolt as it may ruin the threads.

Unpack the Grill

1. Remove the packing materials from around the perimeter of the ceramic

Fire Ring and lift out of the grill. Set it aside. It will be necessary to hold

the Fire Ring from the inside to avoid pinching your ngers. Fig. 3

Proceed to step 9.

10. Replace the grate and then place the cooking grid on top of the ceramic Fire Ring. Fig. 9

11. Place the Chimney Top Control on the top of the grill. No fasteners are

necessary. Fig.10

12. To properly install your side shelves hold the shelf close to the inside

edge in a downward position and drop the pin into the shelf bracket.

Slowly lift up the shelf until the locking hook is aligned with the pin stop

tab.

Great job! You are now ready to barbecue!

ASSEMBLING YOUR GRILL Page 7

Fig.9a Fig.9b

Fig.10

Fig.11

Fig.12

Note:

If you position the Chimney Top hinge on the right side it will close when the grill is

opened (recommended).

Note:

Side shelf brackets are part of the shelf kit and must be attached. Fig.11

Please ensure that the left and right shelves are properly installed. The right

shelf has a protective metal plate to prevent the grill bands from touching the

wood shelves.

Note:

When you lift the shelf up, slide the hook on the shelf support back so they align

underneath the Stop Tab. Fig.12

Stop Tab

USING YOUR GRILL Page 8

1. Remove the cooking grid.

2. If you have charcoal left in the grill from the previous re, stir it around enough to knock the ash down

through the grate. This will allow better air ow for a quicker start. The remaining charcoal is good to use

again.

3. Pour lump charcoal into the rebox until it covers the series of round holes in the rebox. (see Fig.13)

You may ll it to the top of the rebox if you need to cook or smoke for more than three hours.

Starting the Fire

4. If you are using a combustible re-starter, nestle it down into the charcoal. You may place re starters

in more than one spot in the charcoal if you want to get the whole area burning more quickly for high

temperature grilling and searing. You may stack some charcoal around the starter to speed up the

process. Be sure to leave enough air space around the stacked charcoal for the air and ame or it will not

burn properly. Now light the starter. Fig.13

5. If you are using an electric re-starter, nestle it down into the charcoal so it is resting on the charcoal just

above the grate. The charcoal should envelop the lower half of the starter element. Plug in the starter

and let it operate for no more than 8 minutes.

6. Unplug and remove the starter within 8 minutes to avoid damaging the starter. You do not have to leave

the starter in longer as the re will continue to increase after removing it. Fig.14

7. Replace the cooking grid and close the grill. Swing the chimney top damper fully open until the grill is

up to your desired temperature.

8. When the grill has reached your desired cooking temperature, adjust the top and bottom damper for the

desired temperatures as seen on next page.

9. When you are nished cooking, close the Top and Bottom Air Controls to snu the re out. This will

preserve any remaining coals for the next use.

Fig.14Fig.13

CAUTION: DO NOT USE LIGHTER FLUID INSIDE THIS GRILL! IT WILL VOID YOUR WARRANTY.

Not only does lighter uid create a bad smell in the neighborhood and on your food, but it is not good for the ceramics

in your grill.

Note:

You may close the air controls before the food is done as it will hold the heat for a long time and allow the food to

nish cooking.

CLEANING YOUR GRILL Page 9

Cooking Grids

Safe Practices

It is not necessary to use soap to clean the Cooking Grids after every use. The easiest way to keep your

grids clean is by using a brass or stainless steel bristled brush just before cooking. After starting the re,

put the Cooking Grid into position and allow it to heat up at a high temperature setting for 5 to 10 minutes.

Brush the grids, close the lid and slow the grill down with the air control. A good way to nish cleaning and

prepare the grid for food is to wipe it with a cloth soaked with vegetable or olive oil. You can use your grill

brush to aid in the application. A small piece of cloth will normally stick to the wire brush quite well. Do this

just before putting food on.

Ash is removed through the Bottom Air Control. Prevent ash from lling up to the re grate. The Ash

Cleaning Tool (ACT) or similar shaped implement is used to scrape the ashes out the door and into a metal

container. DO NOT STORE ASHES IN A COMBUSTIBLE CONTAINER.

We recommend that the top and bottom air controls be adjusted in sync with one another so that the

bottom control is not open much more than the top control. As air reaches the re and is superheated it

expands greatly. With this in mind, it is better to slow the re down by closing the bottom damper and then

reducing the top damper opening to ne tune the temperature.

Starter & High Temperature Grilling and Searing 500º to 600º

Medium Temperature for Roasting and Grilling 300º to 450º

Low Temperature for Smoking 200º to 300º

Top Control - Swing chimney top fully open.

Top Control - Chimney top closed with

spin damper holes 100% open.

(Swing chimney top open a little if needed for more heat)

Top Control - Chimney top closed with

spin damper holes open halfway.

Bottom Control - 1 to 2 inches open.

Bottom Control - approx. 1/2 to 1 inches open.

Bottom Control - approx. 1/8 to 1/4 inches

WARNING::

If it has only been a couple of minutes since you have closed down the air setting on a very hot fire, do not

abruptly open the lid. As with most grills, this can cause the additional smoke in the top of the grill to ignite

into flame when it is open. When opening the grill it is always good practice to open the Chimney Top rst and then

lift the lid open one or two inches and hold there for a count of 5. Then open the lid fully. This allows the excess smoke

to exit the grill safely.

Inhaltsverzeichnis

Andere Hanover Grill Handbücher

Hanover

Hanover 500325 Bedienungsanleitung

Beliebte Grill Handbücher anderer Marken

Orbegozo

Orbegozo GR 2300 Bedienungsanleitung

bora

bora PT11 Bedienungsanleitung

Klarstein

Klarstein 10031664 Bedienungsanleitung

Garland

Garland MWE3W Bedienungsanleitung

Char-Broil

Char-Broil 463722714 Bedienungsanleitung

Nexgrill

Nexgrill 720-0830HK Bedienungsanleitung

Kenmore

Kenmore 415.16123800 Bedienungsanleitung

Camp Chef

Camp Chef PG24CLAU Bedienungsanleitung

Tucker Barbecues

Tucker Barbecues GTR Series Montageanleitung

Monogram

Monogram ZGG540NCP1SS Bedienungsanleitung

Equipex

Equipex Sodir Savoy Bedienungsanleitung

Gaggenau

Gaggenau VR 414 610 Bedienungsanleitung

Miele

Miele KM 408-1 Bedienungsanleitung

George Foreman

George Foreman GGR50B Bedienungsanleitung

AOG

AOG T series Bedienungsanleitung

Gorenje

Gorenje TG2000CB Bedienungsanleitung

Weber

Weber Genesis Silver-B Permamount NG 051701 Bedienungsanleitung

Glen

Glen SA 3037 Bedienungsanleitung