Hanwha Vision XWV-3010 Bedienungsanleitung
XWV-3010
SSM workstation
Quick Guide
Copyright
©2023 Hanwha Vision Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered
trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or
wholly, without formal authorization.
Disclaimer
Hanwha Vision makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee
shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
Hanwha Vision reserves the right to change the contents of this document without prior notice.
Design and specications are subject to change without prior notice.
SSM workstation
Quick Guide
4_ Overview
Overview
Before reading the user manual
Be sure to read the following before reading the user manual.
• This manual is copyrighted by the manufacturer.
• This manual cannot be reproduced without permission.
• We are not responsible for any damage caused by using products other than the standard product or using the
product for the purpose other than mentioned in the manual.
• If you need to open the case and touch the inside of the case for troubleshooting, always contact the dealer where
you purchased the product for professional help.
• Do not allow water or liquid to come into contact with the connections of the product.
• Do not apply excessive force or shock.
• Do not pull the power cord by force.
• Do not disassemble the product.
• Use only within the rated input/output power range.
• Use only approved power cords.
• For products with an input ground, be sure to use it with a grounded power plug.
• If a wrong battery is used, there is a risk of an explosion. Never replace the batteries with ones that aren’t the same
model or equivalent product.
• Be cautious so that the batteries are not exposed to excessive heat, such as sunlight or fire.
• Place the power plug where it can be easily operated. If there is a problem with the product, you should unplug the
power plug to completely terminate the power. The power will not be completely terminated by only turning off
the main body’s power button.
5
●OVERVIEW
Notes, Cautions, and Warnings
MNotes Provides important information which helps you use the product more efficiently.
JCautions Explains the risk of hardware damage or data loss while teaching how to prevent these
problems.
JWarnings The warning explains that there is a risk of property loss, bodily injury, or death.
6_ Overview
Overview
The manual of this product is composed as follows.
yQuick Guide
ySSM User Manual
ySystem User Manual
This User Manual is the default setting for user's guide. The User Manual contains the following in order:
If you want to apply the modification to the actual operating environment, refer to the SSM User Manual and the
System User Manual.
yChecking components
yProduct name and functions
yGuide to SSM operation and installation start
J
`The operating system and application software installed on this product are optimized for the hardware of this
equipment.
Do not add or remove any hardware, or update the operating system, or install any other software.
Or it may cause the risk of electric shock and product performance degradation.
Configuration and Tips of User Manual
7
●OVERVIEW
Package Contents
Main body Mouse Power cord
mDP to DP adapter Quick Guide
M
`Accessories other than the SSM workstation body are consumables and are excluded from the warranty.
`All manuals can be downloaded from our homepage (www.HanwhaVision.com).
8_ Overview
Overview
Part Names and Functions
Front
a
c
d
e
g
i
b
f
h
No Name No Name
a
Power button and power indicator
f
USB 2.0 port
b
SD card reader
g
USB 3.2 Gen2x2 Type-CⓇport
c
Hard drive operation indicator
h
USB 3.2 Gen2x2 port
d
Universal audio jack port
i
Optical disk drive
e
USB 2.0 port, supports PowerShare
Front
9
●OVERVIEW
Rear
a
c
d
e
f
g
h
i
j
p
k
l
m
o
n
b
No Name No Name
a
Line In/Out re-assignment
i
Power connector port
b
2 DisplayPort 1.4 ports
j
Power supply diagnostic indicator
c
Serial port
k
Loop lock
d
PS/2 keyboard port
l
Network port
e
USB 3.2 Gen 2 port
m
3 USB 3.2 Gen 1 ports
f
2 USB 2.0 ports, supports turning on the power
n
Kensington security cable slot
g
Extended Network port
o
PS/2 mouse port
h
4 Extended mini DisplayPort ports
p
Release latch
10_ Execution
Execution
Power Supply
Plug all of the power cords into the back of the product, and press the power button.
If the product does not turn on, check the following.
1. Make sure that all the power cords have been plugged in rmly, and that they meet the required power
specications.
2. If you are using a power strip, make sure that the power strip is turned on.
J
`If all the power cords are plugged in firmly but the power does not turn on even after you have pressed the power
button, follow the procedure described below.
This product can be operated in power protection mode to protect it in the event of a power outage or instability
in the power supply.
This is similar to the operation of the fuse of the earth leakage circuit breaker. It is not a malfunction of the product.
Follow the steps described below.
1) Unplug all of the power cords from the back of the product.
- If you are using a power strip, turn off the power strip.
2) Wait 10 seconds after the cords have been removed.
- The protection circuit is now initialized, as the current inside the power supply has been discharged.
3) Plug in the power cords again.
- If you are using a power strip, turn it on again.
4) Press the power button on the product.
Inhaltsverzeichnis
