Harbor Breeze FLANAGAN Bedienungsanleitung

HARBOR BREEZE and logo design are trademarks or

ATTACH YOUR RECEIPT HERE

Purchase Date _________________________

ITEM #3786967

FLANAGAN CEILING FAN

MODEL #42461

AS21025

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-888-251-1003, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could also

Español p. 20

TABLE OF CONTENTS

Package Contents .................................................................3

Hardware Contents ................................................................4

Safety Information .................................................................5

Preparation ......................................................................6

Initial Installation ..................................................................7

Standard or Angle Mounting Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Wiring .........................................................................11

Final Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Operating Instructions .............................................................15

Care and Maintenance ............................................................16

Troubleshooting..................................................................16

Limited Lifetime Warranty ..........................................................18

Replacement Parts List ............................................................19

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

A Downrod 1

B Downrod Pin (preassembled to the Downrod [A]) 1

C Downrod Clip (preassembled to the Downrod [A]) 1

D Mounting Bracket (preassembled to Canopy [E]) 1

E Canopy 1

F Canopy Cover (preassembled to Canopy [E]) 1

G Yoke Cover 1

HMotor Assembly 1

I Set Screw (preassembled to the Motor Assembly [H]) 2

J Mounting Bracket Screw (preassembled to the Mounting Bracket [D]) 4

K Fitter Plate (preassembled to the Motor Assembly [H]) 1

L Fitter Plate Screw (preassembled to the Fitter Plate [K]) 3

M Light Pan 1

N Light Pan Screw (preassembled to the Light Pan [M]) 3

O Light Kit 1

P Remote Pack 1

Q Glass Bowl 1

R Blade Arm 5

S Blade 5

R S

O Q

HARDWARE CONTENTS

Wire Connector

Qty. 3

+ 1 extra

Blade Screw

Qty. 15

+ 1 extra

Blade Washer

Qty. 15

+ 1 extra

Motor Screw

Qty. 15

+ 1 extra

(shown actual size)

AA BB CC

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the

product.

• Before you begin installing the fan, disconnect the power by removing fuses or turning o󰀨 the circuit

breakers.

• Make sure all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-199. Hire a qualied electrician or consult a do-it-yourself wiring

handbook if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to

the oor and at least 30 in. from the end of the blades to any obstruction.

• The net weight of this fan is: 15.67lb (7.11kg).

DANGER: When using an existing outlet box, make sure the outlet box is securely attached to

the building structure and can support the full weight of the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan

after installation is complete.

WARNING: To avoid personal injury, the use of gloves may be necessary while handling fan

parts with sharp edges.

WARNING: Using a full-range dimmer switch to control fan speed will cause a loud humming

noise from the fan. To reduce the risk of re or electric shock, do NOT use this fan with any solid-state

speed control device.

WARNING: To reduce the risk of re, electric shock or personal injury, mount the fan to an outlet

box marked “ACCEPTABLE FOR FAN SUPPORT” and use the mounting screws provided with the

outlet box. Most outlet boxes commonly used for the support of lighting xtures are not acceptable

for fan support and may need to be replaced. Consult a qualied electrician if in doubt. Secure the

outlet box directly to the building structure. The outlet box and its support must be able to support the

moving weight of the fan (at least 35 lbs.).

WARNING: To reduce the risk of re, electric shock or personal injury, wire connectors provided

with this fan are designed to accept only one12-gauge house wire and two lead wires from the fan. If

your house wire is larger than 12-gauge and/or there is more than one house wire to connect to the

two fan lead wires, consult an electrician for the proper size wire connectors to use.

WARNING: To reduce the risk of re, electric shock or personal injury, do not bend the blade

arms when installing them, balancing the blades or cleaning the fan. Do not insert objects between

the rotating fan blades.

WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use

of parts OTHER than those provided with this fan will void the warranty.

SAFETY INFORMATION

CAUTION: Read all instructions and safety information before installing your new fan. Review the

accompanying assembly diagrams.

CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present.

CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are

secured.

CAUTION: This device complies with part 15 of FCC Rules. Operation is subject to the following

two conditions: 1) This device may cause harmful interference, and 2) this device must accept any

interference received, including interference that may cause undesired operation.

CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment o󰀨 and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver

--Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is

connected.

--Consult the dealer or an experienced radio/TV technician for help.

Please note changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

HKC-US

3350 Players Club Parkway, Suite 225

Memphis, TN 38125

1-888-251-1003

PREPARATION

Before beginning the assembly of this product, ensure that all parts are present. Compare all parts

with the package contents list and hardware contents list. If any part is missing or damaged, do not

attempt to assemble the product.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety

Glasses, Step Ladder, Wire Cutters and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape Measure and Wiring Handbook

INITIAL INSTALLATION

1. Turn o󰀨 the circuit breakers and the wall switch to the

fan supply line leads.

DANGER: Failure to disconnect the power supply

prior to installation may result in serious injury or death.

2. Determine the mounting method to use.

Standard Mounting is best suited for ceilings 8 ft. or

higher. For taller ceilings you may want to use a longer

downrod (not included).

Angle Mounting is best suited for angled or vaulted

ceilings. A longer downrod is sometimes necessary to

ensure proper blade clearance.

Important:If using the angle mount, check to ensure

the ceiling angle is not steeper than 16°.

Flushmount is not available for this item.

Closemount is not available for this item.

Standard Mounting

Flushmount Closemount

Angle Mounting

3. Ensure the blades (S) will be at least 30 in. from any

obstructions. Also check the downrod (A) length to

ensure the blades (S) will be at least 7 ft. above the oor.

7 feet

minimum

30 in.

minimum

INITIAL INSTALLATION

4. Loosen all four preassembled mounting bracket

screws (J), then completely remove the two

mounting bracket screws (J) from the round holes

of canopy (E). Set aside for later use. Turn the

canopy in a counterclockwise direction.

Detach mounting bracket (D) from canopy (E).

5. Attach mounting bracket (D) to outlet box (not

included) using screws and washers provided with

the outlet box.

CAUTION: It is very important to use the proper

hardware when installing the mounting bracket (D) as

this will support the fan.

Standard

Mounting

Angle

Mounting

STANDARD OR ANGLE MOUNTING INSTRUCTIONS

1. Remove the downrod clip (C) and downrod pin (B)

from the downrod (A). Then partially loosen the

set screws (I) in the yoke at the top of the motor

assembly (H).

2. Insert the downrod (A) -- or a longer downrod (not

included), if required -- through the canopy (E) and

yoke cover (G). Feed the wires from the fan through

the downrod (A).

3. Slide the downrod (A) into the yoke, align the holes,

then re-install the downrod pin (B) and downrod clip

(C). Secure with set screws (I) and slide the yoke

cover (G) down until it rests on top of the motor

assembly (H).

Yoke

STANDARD OR ANGLE MOUNTING INSTRUCTIONS

4. Depending on the length of downrod you use, you

may need to cut the lead wires back to simplify the

wiring. If you decide to cut back the lead wires, it is

suggested you do so in the following manner: Take

the lead wires and make sure you have pulled them

all the way through the top of the downrod. Measure

8 inches of lead wire, then cut the excess wire o󰀨 with

wire cutters (not included).

5. If you decided to cut back the lead wire in Step 4, strip

1/2 in. of insulation from the end of the white wire.

Twist the stripped ends of each strand of wire within

the insulation with pliers (not included). Repeat the

step for the black wire.

Note:If you did not cut back the lead wires in Step 4,

Step 5 is not necessary and you may proceed to Step

6 instead.

6. Install the ball end of the downrod (A) into the opening

of the mounting bracket (D). Align a slot in the ball

with the tab in the mounting bracket (D).

Important:The downrod (A) should not rotate in the

mounting bracket (D) if installed properly.

DANGER: Failure to align a slot in the ball with

the tab may cause the fan to wobble or fall, which

could result in serious injury or death.

Tab

Slot

8 in.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Harbor Breeze Lüfter Handbücher

Harbor Breeze

Harbor Breeze AERO CEILING FAN E-AER52BRZ5LKRCI Bedienungsanleitung

Harbor Breeze

Harbor Breeze 0883783 Bedienungsanleitung

Harbor Breeze

Harbor Breeze LAKE LAGODA LP8300LAZ Bedienungsanleitung

Harbor Breeze

Harbor Breeze TG52BNK3D1RC Bedienungsanleitung

Harbor Breeze

Harbor Breeze RLG52NWZ5C3L Handbuch

Harbor Breeze

Harbor Breeze KEYPORT HUGGER 40141 Bedienungsanleitung

Harbor Breeze

Harbor Breeze CEDAR HILL Bedienungsanleitung

Harbor Breeze

Harbor Breeze FLANAGAN II 42477 Bedienungsanleitung

Harbor Breeze

Harbor Breeze COGDELL COG60BNK7LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze L1305 Bedienungsanleitung

Harbor Breeze

Harbor Breeze Crosswinds II 40821 Bedienungsanleitung

Harbor Breeze

Harbor Breeze MAZON MZ44MBLK3LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze WELLSBORO 42072 Handbuch

Harbor Breeze

Harbor Breeze FAIRWIND Bedienungsanleitung

Harbor Breeze

Harbor Breeze MERRIMACK II 41125 Bedienungsanleitung

Harbor Breeze

Harbor Breeze C-TMH44CH5D1R Bedienungsanleitung

Harbor Breeze

Harbor Breeze TILGHMAN WCK52LMW5N Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40094 Bedienungsanleitung

Harbor Breeze

Harbor Breeze E-ER56ORB3LKLR Bedienungsanleitung

Harbor Breeze

Harbor Breeze 42079 Bedienungsanleitung

Harbor Breeze

Harbor Breeze LP8071LBN Bedienungsanleitung

Harbor Breeze

Harbor Breeze FW60AGV3LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze 52 IN CLASSIC STYLE 40081 Bedienungsanleitung

Harbor Breeze

Harbor Breeze PRESTWICK 42868 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung