Harbor Breeze RLG52NWZ5L Bedienungsanleitung

Sailor Bay Ceiling Fan

Harbor Breeze® is a registered trademark

ITEM #1461040

1461041

1461042

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Sunday.

Purchase Date

Español p. 21

MODEL #RLG52NWZ5L

RLG52BNK5L

RLG52WW5L

BM19336

4007498

ATTACH YOUR RECEIPT HERE

ADJUNTE SU RECIBO AQUÍ

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate the

product.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for

repairs, it must be shipped in its original packaging to ensure proper protection against damage that

might exceed the initial cause for return.

• Make sure all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring

handbook if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the

floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 18.74 lbs.

Safety Information ................................................................................................................2

Package Contents ................................................................................................................5

Hardware Contents ............................................................................................................

Preparation

...........................................................................................................................

Initial Installation ...................................................................................................................

Downrod-Style Fan Mounting ..............................................................................................

Closemount-Style Fan Mounting ........................................................................................10

Wiring ..................................................................................................................................12

Final Installation ...............................................................................................................

..14

Operating Instructions ...................................................................................................

..16

Care and Maintenance .....................................................................................................

.18

Troubleshooting.................................................................................................................

.18

Limited Lifetime Warranty .................................................................................................

Replacement Parts List ......................................................................................................20

TABLE OF CONTENTS

SAFETY INFORMATION

To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box

marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. (15.9 KG) OR LESS" and use

mounting screws provided with the outlet box. Most outlet boxes commonly used for the

support of lighting fixtures are not acceptable for fan support and may need to be replaced.

Consult a qualified electrician if in doubt.

When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box; do NOT use a

plastic outlet box. Secure the outlet box directly to the building structure. The outlet box and its

support must be able to support the moving weight of the fan (at least 35 lbs.).

To avoid personal injury, the use of gloves may be necessary while handling fan parts with

sharp edges.

To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan

are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your

house wire is larger than 12-gauge or there is more than one house wire to connect to the

corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.

To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control

device or control fan speed with a full range dimmer switch.

To reduce the risk of fire, electrical shock or personal injury, do not bend the blade arms when

installing them, balancing the blades or cleaning the fan. Do not insert objects between the

rotating fan blades.

To reduce the risk of personal injury, use ONLY parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

Before installation, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

WARNING

DANGER

CAUTION

When using an existing outlet box, make sure the outlet box is securely attached to the building

structure and can support the full weight of the fan. Failure to do this can result in serious injury or

death. The stability of the outlet box is essential in minimizing wobble and noise in the fan after

installation is complete.

To reduce the risk of serious bodily injury, DO NOT use power tools to assemble any part of the

fan, including the blades.

Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.

Before beginning installation, carefully check all screws, bolts and nuts on fan motor assembly to

ensure they are secure.

SAFETY INFORMATION

CAUTION

Modifications not approved by the party responsible for compliance could void the user's authority

to operate the equipment.

*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Distributed by: Litex Industries Inc., P.O. Box 535639, Grand Prairie, TX, 75053; 1-800-527-1292

NOTE: Dimmable to 10% with select dimmers. See Lowes.com for more information.

IMPORTANT: You must use the parts provided

with this fan for proper installation and safety.

A Downrod 1

B Canopy 1

C Mounting Bracket 1

D Motor Housing 1

E Star Washer 4

(preassembled)

F Light Kit Fitter 1

G Blade 5

H Blade Arm 5

I Glass Shade 3

J Motor Screw 10

(preassembled) + 1 extra

DESCRIPTIONPART QUANTITY

PACKAGE CONTENTS

DESCRIPTIONPART QUANTITY

K Lock Washer 10

(preassembled) + 1 extra

L Pin (preassembled) 1

M Clip (preassembled) 1

N Bulb 3

O Canopy Mounting Screw 4

(preassembled)

P Switch Housing Screw 3

(preassembled)

PREPARATION

HARDWARE CONTENTS (shown actual size)

Before beginning assembly of product, make sure all parts are present. Place motor on carpet or on

foam to avoid damage to ﬁnish. Compare parts with package contents list and hardware contents list.

If any part is missing or damaged, do not attempt to install, operate or assemble the product.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety

Glasses, Stepladder and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and

Wire Cutters

Turn off circuit breakers or fuse and wall switch to

the fan supply line leads.

DANGER: Failure to disconnect power supply

prior to installation may result in serious injury or

death.

INITIAL INSTALLATION

OFF

AA DD

Pull Chain

Extension

Qty. 2

Wire

Connector

Qty. 4

Blade

Screw

Qty. 15

+ 1 extra

Blade

Washer

Qty. 15

+ 1 extra

Check to make sure blades (G) will be at least

30 inches from any obstruction. Check downrod (A)

length to ensure blades (G) will be at least 7 ft.

above the floor.

INITIAL INSTALLATION

7 ft.

min.

30 in.

min.

2. Determine mounting method to use.

A. Downrod mount (standard or angled ceiling)

B. Closemount (standard ceiling only)

IMPORTANT: If using the angle mount, ensure the

ceiling angle is not steeper than 19°.

*Helpful Hint: Downrod-style mounting is best

suited for ceilings 8 ft. or higher. For taller ceilings

you may want to use a longer downrod (not

included). Angle-style mounting is best suited for

angled or vaulted ceilings. A longer downrod is

sometimes necessary to ensure proper blade

clearance.

19° max.

Secure mounting bracket (C) to outlet box (not

included) using screws, spring washers and flat

washers provided with the outlet box.

*NOTE: It is very important you use the proper

hardware when installing the mounting bracket

IMPORTANT: If using the angle mount, make

sure open end of mounting bracket (C) is installed

facing the higher point of the ceiling, and ensure

the ceiling angle is not steeper than 19°. Open End

ANGLE MOUNTSTANDARD

MOUNT

4. 4

INITIAL INSTALLATION

5. Remove preassembled motor screws (J) and lock

washers (K) from underside of motor housing (D).

If there are plastic motor blocks installed with the

motor screws (J), discard the plastic motor blocks.

Note: Make sure to keep loose hardware separate

to avoid confusion during installation.

For DOWNROD-STYLE FAN MOUNTING,

proceed to Step 1 below.

For CLOSEMOUNT-STYLE FAN MOUNTING,

skip to page 10.

Plastic

Motor

Block

Yoke

DOWNROD-STYLE FAN MOUNTING

Remove pin (L) and clip (M) from downrod (A).

Partially loosen preassembled set screws and

nuts in motor housing yoke at top of motor

housing (D).

Set Screw

& Nut

Side View

2. Insert downrod (A) through canopy (B). Thread

wires from motor housing (D) up through

downrod (A).

Depending on the length of downrod you use,

you may need to cut the lead wires back to

simplify the wiring. If you decide to cut back the

lead wires, it is suggested you do so in the

following manner:

Take the lead wires and make sure you have

pulled them all the way through the top of the

downrod. Start at the TOP of the hanging ball

on the downrod and measure 8 in. of lead wire,

and then cut the excess wire off with wire

cutters (not included).

NOTE: If you do not cut back the lead wires,

Steps 4 and 5 are not necessary and you

may proceed to Step 6 instead.

DOWNROD-STYLE FAN MOUNTING

Slip downrod (A) into motor housing yoke, align

holes and re-install pin (L) and clip (M). Tighten

set screws in motor housing yoke and then

tighten preassembled nuts on the set screws.

Hanging

Ball

8 in.

Yoke

Set Screw

& Nut

Side View

If you decided to cut back the lead wires in Step 4,

strip 1/2 in. of insulation from end of each wire --

white, black, green and blue (if applicable). Twist

stripped ends of each strand of wire within the

insulation with pliers (not included).

5. 5

DOWNROD-STYLE FAN MOUNTING

Install hanging ball of downrod (A) into opening of

mounting bracket (C). Align one of the slots in

hanging ball with tab in mounting bracket (C).

DANGER: Failure to align one of the slots in

the ball with the tab may result in serious injury or

death.

Continue to WIRING on page 12.

CLOSEMOUNT-STYLE FAN MOUNTING

Remove preassembled canopy cover from bottom of

canopy (B). NOTE: To remove canopy cover from

canopy (B), twist canopy cover until the two small

protrusions on the inner lip of the canopy cover align

with the two notches on the bottom of the canopy

(B). Pull on canopy cover to remove.

NOTE: The downrod (A) and canopy cover are not

used in this type of installation.

1. 1

Canopy

Cover

Slot

Tab

Remove every other preassembled screw and lock

washer from top of motor housing (D).

2. 2

Screw

Lock Washer

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Harbor Breeze Lüfter Handbücher

Harbor Breeze

Harbor Breeze OCEANSIDE Bedienungsanleitung

Harbor Breeze

Harbor Breeze E-ER56ORB3LKLR Bedienungsanleitung

Harbor Breeze

Harbor Breeze LP8210LAZ Bedienungsanleitung

Harbor Breeze

Harbor Breeze BRADBURY BRD48BNK6LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze CLASSIC STYLE 00819 Bedienungsanleitung

Harbor Breeze

Harbor Breeze URBANIA E-AR54BNK5C1 Bedienungsanleitung

Harbor Breeze

Harbor Breeze PRESTWICK 42868 Bedienungsanleitung

Harbor Breeze

Harbor Breeze TALAMORE TAL60MBK8LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze 00728 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BOD52MW3 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40105 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 42224 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 00878 Bedienungsanleitung

Harbor Breeze

Harbor Breeze TILGHMAN Bedienungsanleitung

Harbor Breeze

Harbor Breeze Cape Coast E-YLM52WW5C1 Bedienungsanleitung

Harbor Breeze

Harbor Breeze C-TR56BNK3D1R Bedienungsanleitung

Harbor Breeze

Harbor Breeze CEDAR HILL Bedienungsanleitung

Harbor Breeze

Harbor Breeze HTD21011 Bedienungsanleitung

Harbor Breeze

Harbor Breeze CALERA 00830 Bedienungsanleitung

Harbor Breeze

Harbor Breeze WELLSBORO 42072 Handbuch

Harbor Breeze

Harbor Breeze 80210 Bedienungsanleitung

Harbor Breeze

Harbor Breeze Bath Ventilator with Light Bedienungsanleitung

Harbor Breeze

Harbor Breeze Santa Ana LP8294LBN Bedienungsanleitung

Harbor Breeze

Harbor Breeze TG52BNK3D1RC Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung