Harbor Freight Tools 90444 Bedienungsanleitung
OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
WALL MOUNT
KEY SAFE
®
SKU 90444 PAGE 2
SPECIFICATIONS
SAVE THIS MANUAL
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
1. AVOID SHARP EDGES WHEN HANDLING.
2. KEEP PRODUCT USAGE AREA CLEAN.
3. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it
will operate properly and perform its intended function. Check for damaged parts and
any other conditions that may affect its operation. Replace or repair damaged or worn
parts immediately.
4. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical
replacement parts.
5. DO NOT ALLOW CHILDREN TO PLAY WITH THIS PRODUCT. Avoid pinching fingers when
operating.
6. DO NOT SHARE THE COMBINATION WITH THOSE YOU DO NOT WANT TO USE THE
WALL MOUNT KEY SAFE. Avoid writing the combinaton in a place that can be seen by
others. Harbor Freight Tools is not responsible for the careless use of combinations for
the Wall Mount Key Safe.
7. IT IS RECOMMENDED THAT THE KEY SAFE be mounted in a hidden location. Make
sure the mounting of the Key Safe is secure enough so that it can not be easily removed.
DESCRIPTION
4-1/8”L X 2-1/2”W X 1-3/4” Thick
Cast Steel
Hammer-Finish Flat-Black, Grey Rubber Cover
Push Button Combination
1.40 Lbs.
ITEM
Overall Dimensions
Materials
Color Finish
Lock Type
Net Weight
SKU 90444 PAGE 3
INSTRUCTIONS for SETTING THE COMBINATION
1. Use the combination on the “button pad”. Remove Safe Cover (#2) from the Key Safe by
pushing the Latch (#1) down. Flip Safe Cover over. Use a flat head screwdriver and remove
the four Screws (#13). See Figure 1 and Figure 2.
2. Choose a set combination of numbers (10 Maximum). (Using your birth date or drivers license
number for example. Caution: Do not use the address of the location of the Wall Mount Key Safe).
3. Choose your combination number and then one at a time, rotate the Buttons (#5) on the back of
the Safe Cover (#2) until the arrows points UP. This locks the button. Proceed with each Button
until the combination selected is complete. Only the buttons selected may be used to open
the lock.
4. The new combination is now locked into place. The old combination will not work. Replace the
backside of the Safe Cover (#2) making sure that all the Buttons (#5) fit into the slots in the
Safe Cover. Replace the four Screws (#13) that hold the Safe Cover (Backside) to the Safe
Cover.
5. If you want to change the combination simply repeat the previous steps. Remember when the
arrow points “UP” that number is activated. When the arrow on the Button points “DOWN”, the
Button is not activated.
NOTE: Always remember to “clear” the lock by pressing the Reset Button (#3) before inputting the
combination. If you press the wrong Button, you must “reset” the lock and re-enter the correct
combination. As a precaution you will need to “reset” the lock before replacing the Safe Cover (#2)
with the key inside. Recheck to see that it is locked before you leave the area. See Figure 1.
#2
Safe
Cover
Figure 1
#1 Latch
Figure 2
#13
#13
Screws
Four
Places
#2
Safe Cover
(Backside)
Button Button
Turn
until it
is “UP”
1
2
3
4
5
6
7
8
9
10
“Button
Pad”
#3 Reset
Button
SKU 90444 PAGE 4
OPERATING INSTRUCTIONS
1. Press Reset Button (#3). Punch the combination of Buttons (#5) on the “key pad”. Press the
Latch (#1) and lift off Safe Cover (#2). Remove the stored key, hidden in the recess of the
Housing (#17)-(key not included). See Figure 3.
2. When finished with the key, replace in the recessed area. Press the Reset Button (#3).
Punch the combination of Buttons (#5) on the “key pad”. Snap the Safe Cover (#2) back
on the Wall Mount Key Safe using the Latch (#1). Check to be sure the Wall Mount
Key Safe is secure. If not, press “reset” and repeat combination. See Figure 3.
NOTE: Check and double check before leaving the area.
MAINTENANCE
1. For better and safer performance, keep all parts of this product clean and dry.
2. Periodically check to see that all hardware is in place.
“Key Pad”
Latch
#5
Buttons
(1 of 10)
#17, #18
Housing
and
Outerware
#2
Safe
Cover
Figure 3
MOUNTING INSTRUCTIONS
1. Choose a place to mount the Wall Mount Key Safe. See Operating Instructions below.
Punch the combination of Buttons (#5) on the “key pad”. Press the Latch (#1) and lift off
Safe Cover (#2). Use Wood Screws (not included) to mount the Key Safe in the holes
provided. The Wall Mount Key Safe should be mounted securely on a solid wooden
beam or butress. Replace the Safe Cover (#2) as instructed below.
#3
Reset
Button
SKU 90444 Page 5
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EX-
PRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LI-
CENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS
OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
#9
#1
#6 #4
#7
#3
#2
#5
#8
PARTS LIST
Latch
Safe Cover
Reset Mechanism
Spring
Set Button
Spring
Set Spindle
Spring
Engage Plate
Screw
Trifle
Base Plate
PART # DESCRIPTION QTY
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
10
1
1
1
1
1
1
1
Screw
Back Plate
Screw
Key Ring
Housing
Outerware
PART # DESCRIPTION QTY
13
14
15
16
17
18
4
1
1
1
1
1
#10
#11
#18
#13
#15
#17
#12
#14
#16
Recess Area
for Key
and Mounting
Holes
Inhaltsverzeichnis
Andere Harbor Freight Tools Rack & Stand Handbücher
Harbor Freight Tools
Harbor Freight Tools 95621 Bedienungsanleitung
Harbor Freight Tools
Harbor Freight Tools Pittsburgh Motorcycle 64926 Montageanleitung
Harbor Freight Tools
Harbor Freight Tools 91729 Bedienungsanleitung
Harbor Freight Tools
Harbor Freight Tools 94861 Bedienungsanleitung
Harbor Freight Tools
Harbor Freight Tools 92021 Bedienungsanleitung
Harbor Freight Tools
Harbor Freight Tools 69571 Bedienungsanleitung
Harbor Freight Tools
Harbor Freight Tools 91734 Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
