Harken 46.2 ST EL Handbuch

Installation and Maintenance Manual

MRW-D

Powered Radial Winch

46.2 ST EL/HY

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

Index

Introduction 3

Technical characteristics 3

Performance data 3

Weight 4

Maximum working load 4

Outline 5

Installation 6

Procedure 1 7

Procedure 2 8

Winch installation procedure 10

Positioning the self-tailing arm 11

Motor installation procedure 11

Electric wiring diagrams 12

Hydraulic connections diagram 14

Maintenance 15

Washing 15

Maintenance table 15

Disassembly procedure 15

Exploded view with maintenance products 19

Assembly 20

Harken®limited worldwide warranty 21

Ordering spare parts 21

Exploded view 22

Radial Winch 46.2 STA, STC, STCW EL/HY 22

Parts List 24

Radial Winch 46.2 STA EL/HY 24

Radial Winch 46.2 STC EL/HY 25

Radial Winch 46.2 STCW EL/HY 26

Exploded view 27

Radial Winch 46.2 STBBB, STCCC EL/HY 27

Parts List 29

Radial Winch 46.2 STBBB EL/HY 29

Radial Winch 46.2 STCCC EL/HY 30

Exploded view and parts list 31

Horizontal electric motor 12V / 24V 31

Vertical electric motor 12V / 24V 32

Hydraulic motor 33

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

Introduction

This manual gives technical information on winch installation and maintenance, including

disassembling and reassembling.

This information is DESTINED EXCLUSIVELY for specialised personnel or expert users.

Installation, disassembling and reassembling of the winch by personnel who are not experts may

cause serious damage to users and those in the vicinity of the winch.

Harken®accepts no responsibility for defective installation or reassembly of its winches.

In case of doubt the Harken®Tech Service is at your disposal at techservice@harken.it

This Manual is available only in English. If you do not fully understand the English language, do not

carry out the operations described in this Manual.

NOTICE

To use and understand this manual, user must refer to other documents, available on web site

www.harken.com and listed below:

- The Dual Funtion Control Box user manual, for the use of the Dual Function Control Box.

- The Dual Funtion Control Box installation manual, for all details, informations, wiring schemes and

warnings about its installation

Technical characteristics

Power ratio Gear ratio

1st speed 11,70 : 1 2,30 : 1

2nd speed 46,50 : 1 9,17 : 1

The theoretical power ratio does not take friction into account.

Performance data

Winch 46.2 ST EL (electric)

horizontal motor vertical motor

12 V (700 W) 24 V (900 W) 12 V (1500 W) 24 V (2000 W)

1st

speed

2nd

speed

1st

speed

2nd

speed

1st

speed

2nd

speed

1st

speed

2nd

speed

line speed (m/min)** 26,7 6,7 33,5 8,4 35,1 8,8 42,3 10,7

max load (Kg) 315 1300 315 1300 315 1300 315 1300

**Line speed is measured with no load

motor nominal power (W) current absorption at winch

MWL (A)

12 V 24 V 12 V 24 V

winch 46.2 ST E L horizontal 700 900 180 140

vertical 1500 2000 220 120

Introduction - Technical characteristics - Outline

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

Winch 46.2 ST HY (hydraulic)

1st speed 2nd speed

line speed (m/min)* 52,5 13,2

max load (Kg)*** 315 1300

* at 20 l/min oil ow (5,28 Gal/min)

*** at 120 bar at 20 l/min

NOTE

The ratio of the line load - pressure is evaluated at nominal ow rate.

The performance is evaluated measuring the pressure and ow on the motor ports.

The performance data are based on oil with a viscosity of 35mm2/s [165 SUS] and

temperature of 50°C [120°F].

Weight

ST A EH ST C/CW EH ST A EV ST C/CW EV ST A H ST C/CW H

weight (Kg) 14,9 17,5 16,7 19,3 12,7 15,3

ST BBB EH ST CCC EH ST BBB EV ST CCC EV ST BBB H ST CCC H

weight (Kg) 18,6 18,6 20,4 20,4 16,4 16,4

Versions:

A = drum in anodised aluminium

C = drum in chrome bronze

CW = chrome/white

BBB = all bronze

CCC = All-Chrome bronze

EH = horizontal electric winch

EV = vertical electric winch

H = vertical hydraulic winch

Maximum working load

WARNING!

The maximum working load (MWL) for the 46.2 ST Radial Winch is 1300 Kg (2866 lb)

Subjecting the winch to loads above the maximum working load can cause the winch to fail or

pull off the deck suddenly and unexpectedly during high loads causing severe injury or death.

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

Outline

Vertical electric motor (12 V / 24 V)

Hydraulic motor

Winch 46.2 ST EL/HY Horizontal electric motor (12 V / 24 V)

Winch 46 ST EL/HYWinch 46 ST Winch 46 ST EL HO Winch 46 ST HY

201

Ø101

Ø184

201

Ø101

Ø184

201

Ø101

Ø184

155

201

Ø101

Ø184

130

234

Winch 46 ST EL VT

201

Ø101

Ø184

394

140

Line entry height

Winch 46 ST EL/HYWinch 46 ST Winch 46 ST EL HO Winch 46 ST HY

201

Ø101

Ø184

201

Ø101

Ø184

201

Ø101

Ø184

155

201

Ø101

Ø184

130

234

Winch 46 ST EL VT

201

Ø101

Ø184

394

140

Line entry height

Winch 46 ST EL/HYWinch 46 ST Winch 46 ST EL HO Winch 46 ST HY

201

Ø101

Ø184

201

Ø101

Ø184

201

Ø101

Ø184

155

201

Ø101

Ø184

130

234

Winch 46 ST EL VT

201

Ø101

Ø184

394

140

Line entry height

Winch 46 ST EL/HYWinch 46 ST Winch 46 ST EL HO Winch 46 ST HY

201

Ø101

Ø184

201

Ø101

Ø184

201

Ø101

Ø184

155

201

Ø101

Ø184

130

234

Winch 46 ST EL VT

201

Ø101

Ø184

394

140

Line entry height

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

Installation

The winch must be installed on a at area of the deck, reinforced if necessary to bear a load equal

to at least twice the maximum working load of the winch.

It is the installer's responsibility to carry out all structural tests needed to ensure that the deck can

bear the load.

Harken®does not supply the screws needed to install the winch since these may vary depending

on the deck on which it is to be installed.

It is the installer's responsibility to choose the correct screws taking account of the loads they will

have to bear.

Harken®assumes no responsibility for incorrect installation of its winches or for an incorrect choice

of mounting screws.

DANGER!

Incorrect installation of the winch may cause severe injury or death. Consult the yard that built

the boat in the case of doubt over the correct positioning of the winch.

WARNING!

Failure to use the correct number and type of mounting fasteners or failure to ensure the

correct deck strength can result in the winch pulling off the deck suddenly and unexpectedly

during high loads causing severe injury or death.

WARNING!

Verify the entry angle of the sheet. This must be 8° with tolerance of

±2°, to avoid sheet overrides and damaging the winch or making the

winch inoperable leading to loss of control of the boat which can lead to

severe injury or death.

WARNING!

Mount the winch on the deck so that the drive gear is positioned where

the sheet enters the winch drum.

Incorrect position of drive gear can weaken winch leading to failure

which can cause an accident leading to severe injury or death.

NOTICE

For winch STA, STC and STCW versions only

You can find the icon on the skirt to identify

the drive gear position.

After correctly positioning the nal drive gear with respect to the load, check that the motor,

gearing, electrical wiring and/or hydraulic pipes can be housed below decks. To help nd the

optimal compromise, remember that, to make the installation of the motor easier, It can be coupled

to the winch in different positions.

Once you have decided the correct mounting position for the winch on the deck and checked the

space available below deck, proceed with the installation.

drive gear

SHEET

8°

Installation

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

The winch can be installed following one of the two procedures below (Procedure1 or Procedure 2):

Procedure 1

To install the winch you must remove the drum and use bolts as described ahead.

Tools needed: One medium at-bladed screwdriver

To identify the various parts, refer to the exploded view at the end of this Manual.

Torque to apply when assembling

1. Pull out the disconnect rod n°21 2. Unscrew the central screw ( 2Nm/18 in-lb)

3. Slide off the assy socket n°31 and the cover

n°30.

Pay attention to the o-ring in the socket.

4. Unscrew the three screws n°29

(4Nm/35 in-lb)

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

5. Remove the self-tailing arm n°28 by rotating

and lifting it.

1. Remove the skirt n°2 with the help of the

screwdriver placed as shown by the symbol

6. Lift off the drum n°24

2.Take off the base n°2

Winch STA, STC and STCW versions:

Install the winch on the deck in the position you have chosen, keeping in mind the limits described

on page 4 and using socket head (SH) bolts.

Winch STBBB and STCCC versions:

Install the winch on the deck in the position you have chosen, keeping in mind the limits described

on page 4 and using socket head (SH) bolts or hexagonal headed bolts (HH).

Procedure 2 (not pertinent for ST BBB/CCC versions)

To install the winch, remove the winch skirt and use hexagonal headed (HH) bolts.

Tools needed: One medium at-bladed screwdriver

To identify the various parts, refer to the exploded view at the end of this Manual.

See (paragraph on installation) the limits described on page 6 and using socket head (SH) bolts.

Torque to apply when assembling

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

3. Position the 5 M8 hexagonal headed bolts

in their holes

4. Reposition the skirt n°2 in its housing 5. Press down the skirt to position it correctly

NOTICE

Make sure the skirt is correctly clipped on to the base of the winch.

Install the winch on the deck in the position you have chosen, keeping in mind the limits described

on page 6 and using hexagonal headed (HH) bolts.

Radial Winch 46.2 ST EL/HY

Installation and Maintenance Manual - Mod.D

Winch installation procedure

Carry out Procedure 1 or Procedure 2,then install the winch on the deck in the chosen position.

NOTICE

Before drilling the deck, check the space available below deck for the ange and the motor

A. Position the base of the winch on the deck and mark the position of the holes or use the

drilling cut-out template at the point where you have decided to place the winch.

Below is a reduced scale diagram.

Ø150

46°

64°

70°

64°

Winch outside Ø184

final pinion

position

Ø8

n°5

Ø80 cut out for

powered winches

The drilling cut out template is available on the Harken®website, www.harken.com

B. Remove the winch and drill the ve 8.2 mm and a 80 mm diameter holes.

C. Bolt the base of the winch to the deck using ve M8 bolts (not supplied by Harken®) as

described at Procedure 1 or Procedure 2, correctly chosen for the thickness and type of the boat

deck. Consult the yard that built the boat in case of doubt.

WARNING!

To install the winch on the deck, use only bolts in A4 stainless steel (DIN 267 part11).

Bolts made of other materials may not have sufficient strength or may corrode which can result in

winch pulling off deck suddenly and unexpectedly during high loads causing severe injury or death.

NOTICE

To mount winches on the deck, do not use countersunk bolts.

D. Fill the mounting holes with a suitable marine sealant.

E. Remove the excess adhesive/sealant from the holes and base drainage channels

F. Reassemble the winch following the steps in Procedure 1 or Procedure 2 in the reverse order,

and apply the products indicated in the section on maintenance.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Harken Winde Handbücher

Harken

Harken HighTailer IN171 Bedienungsanleitung

Harken

Harken Performa Winch 80.3 STP Handbuch

Harken

Harken Riggers Winch 200 Bedienungsanleitung

Harken

Harken Powered Performa 60.3 STP E Handbuch

Harken

Harken 42.2 Handbuch

Harken

Harken 20.2 PTBBB Handbuch

Harken

Harken 16.2 Two Speed Winch Handbuch

Harken

Harken 16st Handbuch

Harken

Harken Performa Winch 70.3 STP Handbuch

Harken

Harken 40.2STAACCSH Bedienungsanleitung

Harken

Harken Performa 60.2 STP EL/HY Handbuch

Harken

Harken INLH500KIT.US Bedienungsanleitung

Harken

Harken UniPower Radial Handbuch

Harken

Harken Radiial 40.2 ST Handbuch

Harken

Harken 200 Bedienungsanleitung

Harken

Harken Performa Winch 40.2 PTP Handbuch

Harken

Harken Performa 35.2 PTP Handbuch

Harken

Harken Carbo AirBlock 340 Bedienungsanleitung

Harken

Harken Powered Performa Handbuch

Harken

Harken Performa 46.2 STP Handbuch

Harken

Harken Powered Performa 80.3 STP EL/HY Handbuch

Harken

Harken 50.2 ST EL/HY Handbuch

Harken

Harken 35.2 PT Handbuch

Harken

Harken 40.2 ST EL Series Handbuch

Beliebte Winde Handbücher anderer Marken

WARRIOR

WARRIOR Trojan 40PUS12 Kurzanleitung

SVERO

SVERO 16 Bedienungsanleitung

Warrior Winches

Warrior Winches C10000NH Bedienungsanleitung

Badland Winches

Badland Winches 68146 Bedienungsanleitung

Bush

Bush II Series Bedienungsanleitung

Badland

Badland APEX 5500 Bedienungsanleitung

Quadratec

Quadratec Q9000 Synthetic Handbuch

C-Max

C-Max VIGO Bedienungsanleitung

Comeup

Comeup DV-9 Bedienungsanleitung

Orvea

Orvea Italwinch 805 Bedienungsanleitung

Prowinch

Prowinch PWJTHF300 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LD2000-A Bedienungsanleitung

Topex

Topex 97X080 Bedienungsanleitung

Eastbound

Eastbound MotoWinch 1707001 Bedienungsanleitung

Runva

Runva EWD8000 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Installationsanleitung

Granit

Granit 11157675 Bedienungsanleitung

TREX

TREX TB75 Bedienungsanleitung