Harman System 9098 Bedienungsanleitung
User
Guide
Serial No: A
IMPORTANT
For convenience, write your serial number in the box above and
keep this guide in a safe place. The number can be found on the
rear of the product and also on the Authentification Certificate.
This number MUST be quoted in all communications in order to
obtain technical support and spare parts from either the factory or
your dealer.
1
Microphone
Amplifier
Dual
System 9098
by Rupert Neve the designer
© Harman International Industries Ltd. 1997
All rights reserved.
Parts of the design of this product may be protected by worldwide patents.
AMEK is a trading division of Harman International Industries Ltd.
Information contained in this manual is subject to change without notice and does
not represent a commitment on the part of the vendor. AMEK shall not be liable
for any loss or damage whatsoever arising from the use of information or any
error contained in this manual or through any mis-operation or fault in hardware
or software contained in the product.
No part of this manual may be reproduced, stored in a retrieval system,
transmitted in any form or by any means, electronic, electrical, mechanical,
optical, chemical, including photocopying and recording, for any purpose
whatsoever without the express written permission of AMEK.
It is recommended that all maintenance and service on the product should be
carried out by AMEK or it's authorised agents. AMEK cannot accept any liability
whatsoever for any loss or damage caused by service, maintenance or repair by
unauthorised personnel.
Part No: MANRNDMA Issue 2
Tel: +44 (0) 161 868 2400
Fax: +44 (0) 161 873 8010
E-mail: [email protected]
Web: www.amek.com
Harman International Industries Ltd
Langley House
Third Avenue
Trafford Park
Manchester M17 1FG
United Kingdom
2
Audio Connections
21Specifications
22Warranty
10
11
Block Diagram 12
Installation Location
Rack mounting
Power up and clicks
Cleaning
M-S Operation 16by Rupert Neve
Operational Guide 13
DMA Controls
Contents
7
5
4
Unpacking
Safety
Mains Cable
115V/230V operation
Safety symbols
Earthing
Changing the fuse
3
4
Check List
The following items are included with the
product.
It is recommended that packaging
materials are retained until all expected
items are accounted for and found to be
operating correctly.
Carton
Packet containing:
4 off M6 mounting screws
4 off plastic washers
1 off fuse for 110V operation.
Moulded
IEC
mains lead
Protective foam
materials
Dual Mic Amp
Quality
Certificate
User
Guide
Unpacking
5
Safety
Caution
For your own safety and to avoid invalidation of warranty, all text
marked with these Safety Symbols should be read carefully!
Please keep this information!
IMPORTANT SAFETY INSTRUCTIONS
Important
Please read this manual carefully before connecting this apparatus to the mains
for the first time! Obey the following safety instructions. Read and understand
these instructions before operating the apparatus or doing troubleshooting,
testing, adjustments or repairs. Failure to comply with the safety instructions
may result in personal injury.
Warning
Hazards or unsafe
practices which can
result in minor personal
injury or product or
property damage.
Important
information.
Read this before
proceeding.
Caution
Hazards or unsafe
practices which can
result in severe
personal injury or
death.
Caution - Earthing
This apparatus MUST be earthed. Under no circumstances should the mains
earth be disconnected from the mains lead.
Caution - Changing the Fuse
To avoid the risk of fire replace only with same value and type of fuse as
marked on the unit, 200mA T (230V) or 400mA T (115V). Fuses are 20mm
anti-surge, IEC type.
Using a suitable flat blade screwdriver, press the fuse cap inwards gently and
twist anti-clockwise to release the cap. Fit the new fuse to the cap and replace
it in the fuseholder by reversing the procedure.
Before changing the fuse, always switch off the unit and remove the AC power
cable!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN !
Safety
6
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Do not place the apparatus on an unstable surface.
Do not insert objects through any apertures.
Do not use this apparatus near water.
Unplug the unit before cleaning. Clean only with a damp cloth.
Do not block any of the ventilation openings. Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves
or other apparatus including amplifiers or power supplies that produce heat.
Do not defeat the safety purpose of the polarised or grounding-type plug.
A polarised plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong. The
wider blade or the third prong are provided for your safety. When the plug
provided does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles and the point where they exit from the
apparatus.
Avoid using mains outlets on the same circuits as air control systems or
other equipment that regularly switches on and off.
Only use attachments /accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way such as the power supply cord
or plug is damaged liquid has been spilled or objects have fallen into the
apparatus the apparatus has been exposed to rain or moisture the
apparatus does not operate normally the apparatus has been dropped.
Unplug the unit under these circumstances.
Adjust only those controls that are covered by the operating instructions.
Use only the mains lead provided with the equipment . Other leads may
not have sufficient current rating.
Do not operate this unit with the cover removed.
WARNING - For your own safety and to avoid invalidation of the
warranty please read this section carefully.
7
Mains Cable
The supplied IEC mains cable must be terminated correctly to the AC mains
supply before use. Use only an approved AC plug or power distribution
device. The three cores are colour coded as follows:
The Green/Yellow core in the mains
cable is a safety ground and must be
connected at all times!
Green/Yellow
Brown
Blue
=
=
=
Safety Earth
Live
Neutral
115V/230V Operation
Before adjusting the operating voltage, always switch off the unit and
remove the AC power cable!
To adjust the operating voltage, use a flat blade screwdriver to click the voltage
selector across to the required position until the legend 115V or 230V appears
in the window and fit the appropriate fuse supplied in the fixings pack.
IMPORTANT SAFETY INSTRUCTIONS
8
Sécurité
Précaution
Pour votre sécurité et afin de ne pas interrompre la garantie il est important
de lire attentivement les paragraphes marqués d'un symbole!
Conserver ce document!
Importante
information.
Priere de lire
avant utilisation.
Avertissement
Dangers ou pratiques
dangereuses pouvant
résulter en blessures
personnelles mineures
légères ou en
dommages à la
propriété.
Avis
Dangers ou pratiques
dangereuses pouvant
résulter en des
blessures graves ou
causant la mort.
Important
Ce manuel est à lire attentivement avant de brancher cet appareil pour la
première fois! Suivre les instructions de sécurité. Lire et comprendre ces
intructions avant l'utilisation de l'appareil ou avant dépannage, essai, ajustement
ou réparation. Ne pas se conformer aux instructions de sécurité peut
provoquer de graves blessures.
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR !
Avis - Terre
Cet appareil DOIT être branché à la terre. En aucun cas devoir la terre
principale est débranchée du plomb principal.
Avis - Changer le Fusible
Afin d'éviter un risque de feu, remplacer seulement avec fusible de la meme
valeur et type, 200mA T (230V) ou 400mA T (115V). Les fusibles sont de type
IEC 20mm protection-surtension (pour fusibles).
Avant de changer le fusible, éteindre l'appareil et enlever la prise
d'alimentation! Utiliser un tourne vis à tête plate, appuyer sur le capuchon du
fusible doucement vers l'interieur et tourner dans le sens contraire des aiguilles
d'une montre pour dégager le capuchon. Mettre le nouveau fusible dans le
capuchon et remettre en place en faisant la procédure inverse.
9
Cable de Secteur
Le cable de secteur IEC fourni doit être correctement au cable d'alimentation
avant l'utilisation. Protéger le cordon d'alimentation afin d'éviter qu'il soit
piétiné, écrasé ou pincé, en particulier au niveau des prises de courant, des
fiches femelles et des points de sorties de l'appareil.
Utiliser seulement une prise de courant conforme. Les 3 cables à l'intérieur du
cable d'alimentation sont de couleurs suivantes:
Le cable vert/jaune à
l'intérieur du cable
d'alimentation est la sécurité
terre et doit être toujours
connecté!
Vert/Jaune
Marron
Bleu
=
=
=
Prise de Terre
Phase
Neutre
115V/230V Fonctionnement
Avant le réglage du voltage, toujours éteindre et débrancher l'appareil!
Pour le réglage du voltage, utiliser un tourne vis à tête plate afin de déclancher
le voltage sur la position choisie jusqu'à ce que 115V ou 230V apparaisse dans
la fenêtre et mettre le fusible approprié qui se trouve dans le kit fourni.
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES
10
Installation
Location
This product is designed and screened to minimise internal electromagnetic
emissions and provide immunity to external electromagnetic fields.
To reduce the risk of performance degradation due to external interference,
do not site this unit close to sources of strong magnetic fields such as power
supplies, power amplifiers, loudspeakers etc.
Powering up and Clicks
Clicks may be heard from in/out switches when the product is powered up,
these will dissipate after approximately 10 minutes. This is perfectly normal.
Cleaning
The product should be cleaned with a soft brush around the controls. If the
facia becomes dirty, use a damp cloth with a little household soap to remove
the dirt. DO NOT use solvent cleaners under any circumstances or the facia
may be permanently damaged and warranty invalidated!
Rack Mounting
This product is designed to be rack mounted using the screws and washers
supplied to help preserve the finish of the facia panel.
The facia graphic layer is under-surface printed to provide a robust hard
wearing surface designed to last the life of the product in virtually any operating
environment. Failure to use the supplied fixings may result in damage to the
facia surface which can invalidate the warranty.
It is recommended that additional rack-mount side supports are used in
conjunction with the facia panel fixings, particularly when the unit is mounted in
a flite case or vehicle where vibration and transit shocks can be expected.
Inhaltsverzeichnis
Andere Harman Verstärker Handbücher
Harman
Harman CROWN CT16S Bedienungsanleitung
Harman
Harman JBL GTR-102 Bedienungsanleitung
Harman
Harman JBL Club A600 Bedienungsanleitung
Harman
Harman CA470 Bedienungsanleitung
Harman
Harman Infinity Reference 6001A Bedienungsanleitung
Harman
Harman Crown CDi DriveCore 4|300 Bedienungsanleitung
Harman
Harman JBL Stage A6004 Bedienungsanleitung
Harman
Harman JBL CSA 1300Z Bedienungsanleitung
Harman
Harman Infinity 3004A Bedienungsanleitung
Harman
Harman Infinity REFERENCE 4555A Bedienungsanleitung
Harman
Harman AXYS Dante OCTADRIVE DSP-DN Bedienungsanleitung
Harman
Harman JBL GTO7520 Bedienungsanleitung
Harman
Harman JBL Performance Series Bedienungsanleitung
Harman
Harman Infinity Kappa one K Bedienungsanleitung
Harman
Harman Crown XTi2 Series Bedienungsanleitung
Harman
Harman JBL Club A754 Bedienungsanleitung
Harman
Harman Infinity Kappa Perfect PowerSports Bedienungsanleitung
Harman
Harman crown CDi DriveCore Series Bedienungsanleitung
Harman
Harman Infinity Reference 6001A Bedienungsanleitung
Harman
Harman JBL Apex PA454 Bedienungsanleitung
