Harman JBL CBT Series Bedienungsanleitung

CBT 200LA-1

Assembly & Bracket Installation Guide

INCLUDED:

op Speaker

Module

Bottom Speaker

Module

Coupler

Plate

Speaker

Bracket

Swivel-Tilt

Wall Bracket

M6-34L M6-12L SS Flatwashers

M6-20L

Flat head

M6-Nuts SS Lockwashers Switch covers

[Not shown to relative scale]

CBT 200LA-1 Assembly & Bracket Installation Guide – Page 2

WALL SURFACE MOUNTING

Note that the BRACKET ASSEMBLY consists of a SPEAKER BRACKET and a WALL BRACKET.

1) RUN WIRING -- Run the wiring from the power amplifier to the location desired for mounting the

JBL CBT Loudspeakers.

2) ATTACH

WALL BRACKET TO WALL -- Using a level to ensure that the WALL BRACKET is

straight, secure the WALL BRACKET to the wall. Be sure to use the appropriate wall anchors for

attaching the bracket. Use all four screw holes for maximum integrity and safety. Be sure that the

slot feature is at the top.

Hardware for attaching WALL BRACKET to wall not included.

CBT 200LA-1 Assembly & Bracket Installation Guide – Page 3

3) ORIENTING TOP & BOTTOM SPEAKER MODULES

This drawing shows the proper orientation of the two speaker modules, where the coupler plate

attaches and where the wall bracket attaches (onto the coupler plate).

IMPORTANT: Note that the speaker will not work correctly if the TOP AND BOTTOM

SPEAKER MODULES are not oriented exactly as shown.

CBT 200LA-1

Assembly

1) Align Top & Bottom

Speaker Modules

So Arrows Point

at Each Other

2) Attach Coupler Plate

Using 8 Included

Flathead Bolts

For Bottom Module:

CAUTION:

Installation must be

done by qualified

persons using safe

rigging standards.

For Top Module:

CBT 200LA-1

Assembly

1) Align Top & Bottom

Speaker Modules

So Arrows Point

at Each Other

2) Attach Coupler Plate

Using 8 Included

Flathead Bolts

CAUTION:

Installation must be

done by qualified

persons using safe

rigging standards.

CBT200LA-1

Assembly

1)Align Top & Bottom

SpeakerModules

SoArrows Point

atEach Other

2)Attach Coupler Plate

Using8 Included

FlatheadBolts

CAUTION:

Installationmust be

doneby qualified

personsusing safe

riggingstandards.

CBT200LA-1

Assembly

1)Align Top & Bottom

SpeakerModules

SoArrows Point

atEach Other

2)Attach Coupler Plate

Using8 Included

FlatheadBolts

CAUTION:

Installationmust be

doneby qualified

personsusing safe

riggingstandards.

Coupler Plate

(8 flathead bolts)

Switches at the End of the Column

Labels Show Orientation and Gives Instructions

(Point Arrows Toward Each Other)

Swivel/Tilt

Wall Bracket

(4 panhead bolts)

TOP SPEAKER MODULE

BOTTOM SPEAKER MODULE

CBT 200LA-1 Assembly & Bracket Installation Guide – Page 4

4) CONNECT SPEAKER MODULES TOGETHER VIA COUPLER PLATE

Attach COUPLER PLATE to the TOP AND BOTTOM SPEAKER MODULES, as shown, with 8

pcs of M6-20L flathead bolts, through to TOP AND BOTTOM SPEAKER MODULE’S rear

cabinet insert points.

5) ATTACH SPEAKER BRACKET TO 4 THREADED HOLES ON COUPLER PLATE

Attach Speaker Bracket to the 4 indicated threaded points on the Coupler Plate using the

included M6-12L (6 mm diameter, 12 mm long) bolts, with lock washers and flat washers.

Threaded points

for attachment of

Wall Bracket

(use included

M6 x 12 mm

pan-head bolts)

Threaded points

for attachment of

Wall Bracket

(use included

M6 x 12 mm

pan-head bolts

IMPORTANT: Because of the height of this speaker, the speaker bracket MUST be

installed to these threaded points on the Coupler Plate. Do NOT install the bracket

to any other positions on the speaker.

Speaker Section of

Speaker/Wall Bracket

Assembly

M6L12

BOLT

LOCK

WASHER

FLAT

WASHER

[4 Places]

Coupler Plate

(already installed on speaker)

CBT 200LA-1 Assembly & Bracket Installation Guide – Page 5

6) SLIDE SPEAKER WITH

SPEAKER BRACKET ONTO WALL BRACKET

nOnce the wall mount has been attached to the wall and speaker mount has been attached

to the speaker, loosely install the M6-L34 PIVOT BOLT (bolt, lock washer and flat washer on

one side and flat washer, lock washer & nut on the other side) of the WALL BRACKET. Then

slide the speaker so that the SPEAKER BRACKET engages into the WALL BRACKET,

dropping the hook slot of the SPEAKER BRACKET onto the PIVOT BOLT (which will already be

installed loosely in the WALL BRACKET), as shown in Drawing n.

FLAT

WASHER LOCK

WASHER M6-34L

BOLT

FLAT

WASHER

LOCK

WASHER

M6 NUT

PIVOT BOLT LOCATION

[Same hardware order

for both bolts]

CBT 200LA-1 Assembly & Bracket Installation Guide – Page 6

oInsert the top tilt-angle bolt through the appropriate hole – one of the preset angle holes or the

slot for continuous adjustment capability (see below for more information about tile angles).

Install with M6-L34 bolt, lock washer and flat washer on one side and flat washer, lock washer &

nut on the other side, as shown in Drawing o. Make sure bolt goes through holes in WALL

BRACKET and in SPEAKER BRACKET.

pFinal BRACKET ASSEMBLY is shown in Drawing p.

TIGHTEN THE BOLTS.

7) MORE ABOUT TILT ANGLES -- The bracket allows for +/-15 degrees of up or down tilt, however

because of the height of this speaker, the end of the speaker hits the wall at any angle greater

than 10 degrees.

PRE- SET ANGLES and CONTINUOUSLY VARIABLE ANGLE -- The bracket has through holes

for mounting angles of +/- 15 degrees in 5 degree increments. There is also a slot above the set of

holes for continuously variable adjustment. The pre-set angles are recommended for accurate

aiming in 5 degree increments and the slot for any angle between 5 degree increments. Either

can be utilized for setting the speaker’s tilt angle.

8) SET THE SWIVEL (PAN) ANGLE – Loosen the top and bottom bolts on the pivot. Adjust the

side-to-side swivel (ie, pan) aiming angle of the speaker. Tighten the bolts securely.

Maximum Swivel Angles before Wall Interference – The bracket swivels a full 90 degrees from

side-to-side, however when mounting the CBT speaker onto a wall, the side-to-side swivel is

limited by the end of the speaker encountering the wall. The maximum swivel angle depends on

the up/down tilt angle setting.

9) SAFETY CABLE -- Attach a safety cable (not included) to any of the 6 mm inserts on the back of

the CBT 200LA-1 cabinet using one of the extra included M6 bolts or via an M6 forged shoulder

steel eyebolt. Attach the other end of the cable to a secondary attachment point on the wall.

10) SWITCH COVERS – To discourage tampering with the switch settings, adhesive switch covers are

provided. Peel off the backing from the switch cover and stick the cover over the switch shaft,

lining up the ridge with the recess in the switch shaft.

CBT 200LA-1 Assembly & Bracket Installation Guide – Page 7

11) USING OPTIONAL MTC-CBT-FM1 FLUSH-MOUNT WALL BRACKETS – The optional MTC-

CBT-FM1 brackets allow installing the speaker with its back very close to the wall. It is

recommended to use two brackets – one on the top and one on the bottom – for stability.

CBT 200LA-1 Assembly & Bracket Installation Guide – Page 8

CBT 200LA-1 Bracket Dimensions

CBT200 Install

07/12

JBL Professional

8500 Balboa Blvd.

Northridge, CA 91355

USA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Harman Sprecher Handbücher

Harman

Harman LSR6325P JBL LSR6325P Bedienungsanleitung

Harman

Harman JBL QUANTUM Stream Bedienungsanleitung

Harman

Harman Harman/Kardon ONYX STUDIO 5 Bedienungsanleitung

Harman

Harman Infinity Primus P143 Bedienungsanleitung

Harman

Harman JBL IRX ONE Bedienungsanleitung

Harman

Harman JBL FLIP ESSENTIAL 2 Bedienungsanleitung

Harman

Harman JBL Club 322F Bedienungsanleitung

Harman

Harman Infinity KAPPA 753T Bedienungsanleitung

Harman

Harman JBL C Series Bedienungsanleitung

Harman

Harman JBL Concert 601CF Bedienungsanleitung

Harman

Harman JBL CONCERT 621 Bedienungsanleitung

Harman

Harman infinity REF-6500cx Bedienungsanleitung

Harman

Harman SB400OM Bedienungsanleitung

Harman

Harman REVEL PERFORMA Be4 F226Be Bedienungsanleitung

Harman

Harman JBL PartyBox Ultimate Bedienungsanleitung

Harman

Harman JBL Home Theater Series Bedienungsanleitung

Harman

Harman JBL 2.0 JEMBE Kurzanleitung

Harman

Harman Axys ABF-260/100W PA6 V0 Low Profile Bedienungsanleitung

Harman

Harman JBL PARTYBOX 300 Bedienungsanleitung

Harman

Harman Martin P3 PowerPort 1000 IP Bedienungsanleitung

Harman

Harman JBL PARTYBOX 710 Bedienungsanleitung

Harman

Harman JBL 4312MII Bedienungsanleitung

Harman

Harman JBL PULSE 2 Bedienungsanleitung

Harman

Harman JBL PartyBox Ultimate Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung