Harmar Mobility LiftAL030 Montageanleitung

AL010 Micro Scooter Lift AL050 Micro Power Chair Lift

AL030 Power Tote for

Manual Wheelchairs

CLASS 2

Hitch Adapter

HITCH POST

AL010 - Micro Scooter Lift

LIFT BODY

HARDWARE

PACK

CLASS 2

Hitch Adapter OR CLASS 3

OPTIONAL

HITCH POST

AL030 - Manual Wheelchair Lift

AL050 - Micro Power Chair Lift

LIFT BODY

HITCH ADAPTER

and Stabilizer

HARDWARE PACK

HARDWARE

PACK

U-Bolt

HARDWARE

PACK

CLASS 3

OR CLASS 2

OPTIONAL

HITCH POST

PLATFORM

KEEPER

NOTE: The Platform will not be

allowed to unfold until the platform

has been lowered at least 1 inch.

Unpackaging the Lift

Check the contents of the box against the package check list to be sure that all parts are

included with the lift that are required for proper installation. If any parts are missing or if any damage is

noted, immediately contact your Harmar Dealer. DO NOT attempt to install or use the lift with any missing

or damaged parts.

Models AL010and AL050 are packaged with a standard Class 2 hitch adapter. Model AL030 is packaged with a stan-

dard Class 1 flat bar style hitch adapter and stabilizer. If a different model hitch adapter or a Swing Away option is

required, separate parts must be ordered.

Vehicle Wiring Instructions

BLACKWIRE

Side mount Top mount

Unwind the harness and lay it flat on the ground. One end of

the harness has a black plug; this runs to the back of the

vehicle.

BEGIN ROUTING THE HARNESS AT THE VEHICLE BATTERY.

Connect the black wire to the negative terminal of the battery.

Do not connect the positive terminal yet.

Run wiring harness under, or if possible, through the vehicle,

using cable ties provided to secure the harness to the vehicle.

Position the harness away from the fuel tank, exhaust sys-

tem, brake and fuel lines and any possible pinch points.

Harness should be positioned where it will not come in con-

tact with any road debris.

The harness may be too long for the vehicle. DO NOT CUT

OR SHORTEN THE HARNESS. Use cable ties provided to coil

excess wire and secure it to the vehicle frame.Rear plug

should be secured even to the vehicle’s trailer hitch.

Connect the red wire to the positive battery

terminal.

Wire in a standard 4-contact female flat trailer

connector to the vehicle’s taililights. This will

provide power for the motor cover light.

TRAILER PLUG

ON LIFT HARNESS MOTOR COVER

LIGHT

Ground for light is

provided by main

2 prong power

connector

BROWN WIRE

REDWIRE

COIL

EXCESS

WIRE

HERE

REDWIRE

Side mount Top mount

XCESS

WIRE

HERE

To back

of vehicle

To vehicle's

battery

Harness requires direct connection to

vehicle battery. Do not connect harness

to a secondary power source.

Coil

Excess Wire

Here

Hitch Adapters

Bumper Mount

( Be sure to comply with

vehicle's bumper rating )

CLASS 1

( Flat Bar Style )

CLASS 2

( 1.25 x 1.25 Solid Bar )

Omit stabilizer

CLASS 3

( 2 x 2 TUBE )

Refer to Section 4 or 5

for proper orientation

( right side up or upside down )

Determines lift's height from

the ground

PINCH BOLT

SLEEVE

FOR AL030 ONLY

( CLASS 1 )

Before installing an outside lift on your vehicle the vehicle must be equipped with the correct hitch. If

you are unsure whether your vehicle has, or can accept a hitch, contact your local hitch installer or

visit www.hitch-web.com for vehicle hitch compatibility information.

Please note, your lift comes equipped with a license plate hold light. To power this light vehicle must

have a standard 4-contact trailer light harness. Contact your local hitch installer for more information.

Trailer light wiring is designed to power license plate light ONLY. Attempting to run your lift

from ANY secondary power sorce may cause your lift to operate poorly and could potentially

cause damadge to the motor. All Harmar lifts must be wired directly to the vehicle battery.

Hitch recievers MUST be installed so that it sits parellel to the ground. An improperly

installed hitch can affect the operation of your lift. Some vehicles will require supen-

sion to be supplemented. Contact your local hitch installer or refer to your vehicle’s

owners manual for further guidance.

The following pages will help

you to determine correct

hitch adapter positioning.

Installing the Lift

Measure from Hitch Bar to ground

5-13" 13-15" 15-17" 17-19"

OMIT

STABILIZER

OMIT

STABILIZER

HITCH

POST

HITCH

ADAPTER

To prepare your lift for installation you muct connect the lift to the Hitch Post

and Hitch Adapter provided. Proper positioning is determined by the height of the vehicle hitch.

1. Measure the distance from the bottom of the hitch reciever on the vehicle to the ground.

2. Refer to Figure 1 below to determine correct placement of the hitch adapter.

3. Connect hitch post to lift.

Figure 1

Once you have determined correct configuration, connect the Hitch

Post to the Hitch Adapter following the diagram to the right using

hardware supplied (1/2 - 13 x 3- 1/2” HHCS and lock nuts).

Position the folded lift to the rear of the vehicle with the motor box

folded away from the vehicle. With assistance, carefully lift the unit

up to the Hitch Post and attach it using the 1/2” bolt, washers and

lock nut provided.

Installing the Lift With Swing Away Option

Measure from Hitch Bar to ground

4-12" 12-14" 14-16" 16-17"

Class I Hitch Adapter may NOT be used

when installing a Swing Away.

To prepare your lift for installation with a Swing Away you muct connect the lift to the Swing Away

and Hitch Adapter provided. Proper positioning is determined by the height of the vehicle hitch.

1. Measure the distance from the bottom of the hitch reciever on the vehicle to the ground.

2. Refer to Figure 1 below to determine correct placement of the hitch adapter.

3. Connect hitch post to lift.

Once you have determined correct configuration, connect the

Swing Away to the Hitch Adapter following the diagram to the

right using hardware supplied (1/2 - 13 x 3-1/2” HHCS and

lock nuts).

Position the folded lift to the rear of the vehicle with the motor

box folded away from the vehicle. With assistance, carefully

lift the unit up to the Swing Away and attach it using the 1/2”

bolt, washers and lock nut provided.

Figure 1

*Drawing depicts Class III application. Class II installation is identical.

Swing Away Operation

The Swing Away is an optional accessory that allows for full access to

vehicle trunk, lift gate or tailgates. A swing away may be added to an

existing lift at any time.

Opening the Swing Away

1. Remove the safety pin

CAUTION! Never operate the swing away with a chair or scooter still on the lift. This will

result in damage to the swing away, lift and potentially cause damage to the vehicle and

scooter or power chair. Always ensure that vehicle is on level grown before operating

swing away. Failure to do so could result in injury or damadge to the lift or vehicle.

2. Pull out on the red handle while

pushing away on the lift.

1. Close swing away as you would

a vehicle door, taking care to

stand clear of latching mechanism.

2. Install safety pin. 3. Verify red knob has fully retracted.

Closing the Swing Away

AL010 Lift Operation

"PLATFORM KEEPER"

Insert Key and switch to "ON" position

Press down on Toggle switch momentarily. Once platform has been lowered at least an

inch, unfold the platform. Continue lowering

to the ground.

Drive scooter onto platform as shown. Raise hold down arm.

Raise platform until hold down foot depresses

scooter's deck or until lift's motor ratchets.

To remove the scooter and prepare the lift

for unloaded travel, follow above steps in

reverse order and reverse the direction

of the arrows.

. Verify that the

platform keeper has

engaged the platform's

pin.

Lift should be raised

with the platform folded

and until the lift's motor

ratchets

Safety and Maintenence

Keep hands feet and other objects clear of platform as it lowers to the ground.

Always verify that scooter is securely held down to the lift before attempting to transport.

On some scooters it may be necessary to temporarily move the steering tiller forward to clear the

hold down arm as it lowers into the locked position

Scooters equipped with pneumatic (air-inflated) tires must have properly

inflated tires at all times. Improper tire inflation may change the height of the deck, thereby

changing the hold-down force required.

Use caution when driving over speed bumps, potholes, railroad tracks or other sudden road changes.

Failure to drive carefully and slowly over such obstacles can result in damage to your lift, vehicle or

scooter.

Use care when entering steep driveways. Enter and exit at an angle to avoid dragging lift on the

ground.

Always confirm that lift platform has been fully raised before transporting scooter or unoccupied lift.

Failure to do so can result in serious damage to you lift or vehicle.

Manual Override Feature

This lift is equipped with a Manual Override feature for use if the vehicle or the lift should ever lose power.

Harmar recommends the manual override be used only by Harmar Mobility Authorized Dealers and qualified

mechanics such as roadside assistance technicians.

To ensure safety the lift must be unplugged and the key turned to the off position before manual backup is

engaged. To engage manual backup remove the cap from the top of motor box cover and, using a 3/8"

socket, turn the wrench clockwise to raise the lift or counter clockwise to lower the lift.

CAUTION: TO AVOID THE RISK OF SERIOUS INJURY, NEVER

ATTEMPT TO OPERATE THE MANUAL OVERRIDE WHILE THE LIFT IS

PLUGGED IN TO THE VEHICLE.

AL030 Lift Operation

"PLATFORM KEEPER"

NOTE: The Platform will not be

allowed to unfold until the platform

has been lowered at least an inch.

Insert Key and switch to "ON" position

Press down on Toggle switch momentarily.

1Once platform has been lowered at least an

inch, unfold the platform. Continue lowering

to the ground. Raise hold down arm.

Roll folded chair onto platform as shown.

3Raise the lift until hold down arm has

contacted wheelchair's arm rests.

Remove key if desired.

To remove the chair and prepare the lift

for unloaded travel, follow above steps in

reverse order and reverse the direction

of the arrows.

. Verify that the

platform keeper has

engaged the platform's

pin.

Lift should be raised

with the platform folded

and until the lift's motor

ratchets

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Harmar Mobility Mobilitätshilfe Handbücher

Harmar Mobility

Harmar Mobility AL690 Montageanleitung

Harmar Mobility

Harmar Mobility AL650 Montageanleitung

Harmar Mobility

Harmar Mobility csl500 Beilage

Harmar Mobility

Harmar Mobility AL065 Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL055 Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL030 Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL003 Montageanleitung

Harmar Mobility

Harmar Mobility HELIX Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL600 Pioneer Bedienungsanleitung

Beliebte Mobilitätshilfe Handbücher anderer Marken

Alber

Alber Scalamobil iQ Bedienungsanleitung

Ferno

Ferno CCT-PX Bedienungsanleitung

Otto Bock

Otto Bock Pheon 3R62 Bedienungsanleitung

NRS Healthcare

NRS Healthcare M11090 Bedienungsanleitung

Medline

Medline MDS86835DSHEC Installationsanleitung

HEPRO

HEPRO Gripo Bedienungsanleitung

Guldmann

Guldmann Twin Turner II Bedienungsanleitung

Drive

Drive ROOMBA Bedienungsanleitung

Gate

Gate Balder Bedienungsanleitung

Decon wheel

Decon wheel TNS Notos Bedienungsanleitung

ExoAtlet

ExoAtlet ExoAtlet-II Bedienungsanleitung

Invacare

Invacare Storm Series Bedienungsanleitung

Rhythm Healthcare

Rhythm Healthcare B3800F Bedienungsanleitung

AMF-BRUNS

AMF-BRUNS PROTEKTOR Bedienungsanleitung

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Bedienungsanleitung

Rhythm Healthcare

Rhythm Healthcare C500U Bedienungsanleitung

Lumex

Lumex RJ4200A Bedienungsanleitung

Rebotec

Rebotec Jumbo Bedienungsanleitung