HARVEY COMPASS ST-1500 Bedienungsanleitung

Contents

1. Introduction......................................................................................................................................................... 3

2. Feature Identification........................................................................................................................................ 3

3. Safety for Sliding Table Saws.........................................................................................................................4

4. Product Specifications..................................................................................................................................... 4

5. Inventory...............................................................................................................................................................5

6. Introduction of Mounting Holes..................................................................................................................... 6

7. Modifying Your Table Saw...............................................................................................................................7

8. Assembly..............................................................................................................................................................8

9. Angle Calibation...............................................................................................................................................11

10. Operations....................................................................................................................................................... 11

11. Maintenance....................................................................................................................................................12

1. 介绍..................................................................................................................................................................... 14

2. 产品组成............................................................................................................................................................. 14

3. 安全条例............................................................................................................................................................. 15

4. 产品规格............................................................................................................................................................. 15

5. 包装清单............................................................................................................................................................. 16

6. 安装孔说明......................................................................................................................................................... 17

7. 改装台锯............................................................................................................................................................. 18

8. 安装..................................................................................................................................................................... 19

9. 角度校准............................................................................................................................................................. 22

10. 操作................................................................................................................................................................... 22

11. 保养................................................................................................................................................................... 23

Exploded View and Parts List..............................................................................................................24

English Version

1. Introduction

Model ST-1500 sliding table attachment can be

easily installed on most table saws to greatly

increase crosscutting capabilities.

This attachment for your table saw features a

telescopic crosscutting fence with an adjustable

flip stop for repetitive cuts, and an industrial-grade

sliding table with a linear guide mechanism for

extremely accurate cuts.

Using the extension fence, you can crosscut work

pieces up to 59” (1500mm), the conveniently

positioned fence can also be rotated 60° left or

right by using the built-in miter gauge.

The Model ST-1500 can be installed on a wide

range of table saw brands and sizes.

Main Fit Model:

------110LG (C300), 110S, 110LC (C200)

------ICS, PCS,CNS (For CNS model, this manual

does not provide installation instructions.

------ G0690, G0691, G0899

------ W1819, W1820, W1824

IMPORTANT NOTICE!

Installation requires permanent modification to

your table saw. Read chapter Modifying Your

Table Saw to determine which type of

modification may be required for your saw.

2. Feature Identification

Fig.1

Sliding Table

Extension Table

Support Leg

Fence

Angle Dial

Crosscut Fence Lock Handle

Extension Fence

Extension Fence Lock Knob

Flip Stop

Sliding Table Lock Knob

(underside of the sliding table)

3. Safety for Sliding Table Saws

This attachment is installed on the table saw

for use, special attention should be paid to the

following safety precautions:

1. Kickback happens when the workpiece is

thrown back toward the operator at a high speed.

Until you have a clear understanding of kickback,

including how it occurs, and how to prevent it, DO

NOT operate the table saw with this sliding table

attachment!

2. To prevent flying metal debris causing serious

injuries, always make sure the sliding table

crosscut fence does not contact with the blade

before starting the table saw.

3. If the workpiece should unexpectedly move and

bind with the blade, kickback could occur. Always

make sure the workpiece is placed in a stable

position on the tables and is either supported by

the rip fence or the crosscut fence during cutting

operations.

4. If kickback occurs, the workpiece will be

ejected in a path that is in-line with the blade.

Never have any parts of your body in-line with the

cutting path of the blade during operations.

5. Avoid awkward body and hand positions where

a sudden slip could cause your hands to move

into the spinning blade.

6. To prevent your hands or arms accidentally

contacting with the spinning blade, never reach

behind or over the blade during cutting

operations.

7. When using the rip fence as a stop block for the

crosscut fence, the rip fence must be in front of

the blade. Otherwise, the workpiece could bind

against the rip fence and kickback could occur.

8. To avoid accidental contact with the spinning

blade, always turn the saw OFF and wait until the

blade has completely stopped before removing

any parts of the workpiece from the table.

4. Product Specifications

Sliding table size ..........9" x 47"(228.5 x 1200mm)

Extension table size...9" x 23-3⁄5"(228.5x 600mm)

Maximum table travel ...................60.6"(1540mm)

Max. rip capacity...........................48.8"(1240mm)

Maximum crosscutting length ..........59"(1500mm)

Miter gauge range………….…............ +60°/-60°

Positive Stops..±60°、±45°、±30°、±22.5°、

0°

Vernier Reading Resolution........................... 0.1°

Fence full length….…......................43” (1090mm)

Fence scale……………..……….. Imperial / Metric

Micro-adjustment Accuracy…....0.02 mm / 0.001”

Net weight ....................................... 77 lbs (35Kg)

Fig.2

5. Inventory

Please check the contents of the shipping box

by the inventory list below and Fig.3.

Note:

If you can't find an item on this list, check the

mounting locations or examine the packaging

materials carefully. Occasionally we pre-install

certain components for shipping purposes.

A. Sliding Table Assembly.................................. 1

B. Extension Table Assembly............................. 1

C. Support Leg Assembly.................................. 2

D. Fence Assembly............................................. 1

E. Flip Stop Assembly......................................... 2

F. Fence Lock Handle Assembly...................... 1

G. Table Mounting Hardware Pack 1

— Cap Screws M10-1.5x 25.......................... 3

— Lock Washer 10mm.................................. 3

— D-style Flat Washer 10mm........................ 3

Fig.3

H. Table Mounting Hardware Pack 2

— Cap Screws M8-1.25x 25.......................... 4

— Lock Washer 8mm.................................... 4

— Flat Washer 8mm...................................... 4

— Nut M8...................................................... 4

I. Auxiliary Hardware Pack

— Cap Screws M6-1 x 16.............................. 6

— Lock Washer 6mm.................................... 6

— Flat Washer 6mm...................................... 9

— Nut M6…………........................................ 3

J. Switch Box Mounting Bracket......................... 1

Note:

The hardware supplied with this product are

only applicable to the model shown in the

manual. For other models, the original

hardware can also be modified to fix the

sliding table.

6. Introduction of Mounting Holes

Fig.4

Note:

Only for “SawStop” machine, there are two kinds of installation for selection as you need, see

Fig.5. For other machines, there is only standard mounting.

Fig.5

7. Modifying Your Table Saw

Before mounting the Sliding Table, you may need

to modify your table saw. Some of the steps below

involve removing/installing your rails and

extension wing. For those steps please refer to

your table saw manual.

WARNING:

Disconnect your table saw from electrical power

before beginning any modifications.

For safe and effective use, the sliding table must

be attached to the left side of the main table, and

in a way that the sliding table top is slightly higher

than the table saw top in the full length.

Modifying Your Table Saw as Next Steps:

1. Disconnect the table saw from power!

2. The sliding table must be attached to the left

side of the main table in a way that the sliding

table top is 0.010"–0.020" higher than the top of

the table saw so that work pieces will not be

dragged.

----if you have a wing attached to the left side of

the saw table, remove it.

----if you do not have a wing attached to the left

side of the table or do not have the correct

mounting holes for the sliding table, you need to

drill and tap three M8-1.25 holes into the saw

table to match the sliding table (see Fig.6).

Fig.6

Tip: Use the side of the sliding table to make a

template for marking the mounting hole

locations on the saw table.

3. If the fence rails on your saw prevent the

installation of the Model, please proceed as

following methods:

Method 1: Remove the left extension wing,

reattach the guide tube by removing it and moving

it to right. The front and rear guide rail do not

require any movement. (Note: This method is only

applicable to Harvey’s ALPHA series table saws .)

Method 2: Find the seam between the table and

the left extension wing (or the left edge of the

table if the wing is not installed). Mark the front rail,

rear rail and main tube at 1/4” to the right of the

seam (or edge). Cut off the ends of the rails as

Fig.7 (this is the easiest and fastest option).

Method 3: Remove the rails, move to the right,

then re-mount the rails, which may also require

you to drill (and possibly tap) new holes in your

table and cut small notches into your rails for

access to T-slots in your saw’s table, see Fig.8.

Fig.7

Fig.8

4. If the power switch on your saw is mounted on

the left as Fig.7, you may need to re-mount it to

the bottom of the sliding table or other location.

Mounting holes are reserved at the bottom of the

sliding table to meet the installation requirements

of the table saws listed in this manual.

8. Assembly

After the modification of your table saw, follow

next steps to install the Model ST-1500:

1. Thread the foot pad assemblies into the

bottom of the support legs, as shown in Fig 9.For

now, do not tighten the jam nuts up to the legs so

that you can adjust the height of the legs in a later

step.

2. Turn the sliding table upside down, slide the

support leg T-Bolts into the sliding table T-slot

(Fig.10), then hand-tighten the legs clockwise to

secure them in place.

Note: For the best support, position the

support legs near the ends of the sliding table,

as shown in Fig10.

Fig.9

Fig.10

3. With the help of at least one other person to

support the weight, turn the sliding table assembly

over, and position it against the left side of the

saw table.

4. Pull out the locking knob underneath the

sliding table, then slide the top part to one side to

expose two of the mounting holes, as shown in

Fig.11.

Fig.11

5. Referring to Fig. 4, confirm the right mounting

holes for your table saw. Align the mounting holes,

then thread two cap screws, lock washers, and

flat washers through the sliding table into the

mounting holes of the saw table side.

6. Slide the table surface in the opposite direction

and install the remaining cap screw, lock washer,

and flat washer.

Note: For different types of table saw, there

are differences in the specification and

quantity of hardware, please refer to Chapter 5:

Inventory

7. Adjust the foot pads on the bottom of the legs

to fully support the sliding table, then tighten

them.

Note: Use the precision straightedge to make

sure the table top is parallel with the sliding

table top as you adjust the height of the legs.

8. If the sliding table does not travel exactly

parallel to the saw blade, the workpiece could

bind and kickback toward the operator, causing

serious personal injury. You MUST make sure

that the sliding table travels parallel with the saw

blade before any operation to avoid kickback

injuries. You can shim or post crepe paper on the

side of the table as shown in Fig.12 to adjust the

parallelism (≤0.1 mm).

Fig.12

9. Insert the T-nuts of the extension table into the

T-slot on the outside edge of the sliding table,

then tighten the lock nuts to secure the extension

table in place, as shown in Fig. 13.

Fig.13

10. Slide the miter gauge bar into the T-slot on

the sliding table top near the blade, as shown in

Fig. 14. For full cutting capacity, the miter gauge

bar should be positioned flush with the front edge

of the sliding table. Use a 4mm wrench to turn the

lock screw at the front and rear of the miter gauge

bar COUNTERCLOCKWISE to lock the miter

gauge bar in place.

Fig.14

11. Pivot the crosscut fence counterclockwise

until the left end of the long slot on the crosscut

fence is away off the sliding table. Remove the

T-screw from the crosscut fence Lock Knob and

insert the T-screw up through the slot on the fence

as shown in Fig. 15. Pivot the fence clockwise

and slide the T-screw into the T-slot in the left side

of the sliding table top and screw in the crosscut

fence Lock Knob. Do not tighten the Lock Knob at

this time.

Fig. 15

12. Use a 5mm hexagon wrench to slightly

loosen the crosscut fence from the miter gauge as

shown in Fig. 16. With the blade guard installed,

raise the saw blade to the highest elevation. Pivot

the crosscut fence until it is parallel to the front

edge of the saw table. Slide the crosscut fence

until the right side of the crosscut fence is about

2-1/8 inches (55.5mm) from the left side of the

blade. Re-tighten the screws.

Note: If you want to position the crosscut

fence closer to the blade, be careful not to run

the crosscut fence into the blade guard or

anti-kickback pawls.

Fig.16

Inhaltsverzeichnis

Andere HARVEY Inneneinrichtung Handbücher

HARVEY

HARVEY 57990 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung