Harvil RM-1 Bedienungsanleitung
ASSEMBLY MANUAL RM-1
RM-1 1
e
Hydraulic Resistance
Rowing Machine
The information contained in this manual is subject to change without notice.
We work around the clock and around the globe to ensure that Harvil products
maintain the highest possible quality. However, in the rare instance that your
product is defective or missing parts, contact your retailer to submit parts
requests or warranty claims. Please read the warranty information at the back
of these assembly instructions for further details.
IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS
IN ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT
Thank you for your purchase of this Harvil Product
2
SAFETY INSTRUCTIONS
RM-1
e
1. Save these instructions and ensure that other exercisers read this manual prior to using
the Hydraulic Rowing Machine for the rst time.
2. Read all warnings and cautions posted on the equipment.
3. The Harvil Hydraulic Resistance Rowing Machine should only be used after a thorough
review of the Owner’s Manual. Make sure that it is properly assembled and tightened
before use.
4. We recommend this product to be assembled by 2 people.
5. Keep children away from the Hydraulic Rower. Do not allow children to use or play on
the equipment. Keep children and pets away from the rower when in use.
6. It is recommended that you place this exercise Hydraulic Rower Machine on an
equipment mat.
7. Set up and operate the Harvil Hydraulic Resistance Rowing Machine on a solid level surface.
Do not position the equipment on loose rugs or uneven surfaces.
8. Make sure that adequate space is available for access to and around the Machine.
9. Keep ngers clear of all pinch point when folding and unfolding the equipment.
10. Before using, inspect the equipment for worn or loose components, and securely tighten
or replace any worn or loose components prior to use.
11. Shocks on rowers get HOT during use. To avoid burns, do not touch the shock until it
has time to cool.
12. Consult a physician prior to commencing an exercise program and follow his/her
recommendations in developing your tness program. If at any time during exercise you
fee faint, dizzy, or experience pain, stop and consult your physician.
13. Always choose the workout which best ts your physical strength and exibility level.
Know your limits and train within them. Always use common sense when using the
equipment.
14. Do not wear loose or dangling clothing while using the equipment.
15. Never exercise in bare feet or socks; always wear proper footwear such as running, walking,
or cross training shoes that t well, provide foot support, and feature non-skid rubber soles.
16. Be careful to maintain your balance while using, mounting, dismounting, or assembling
the equipment, loss of balance may result in a fall and serious bodily injury.
17. Do not use the seat to move the equipment. The Seat will move and the Seat Carriage
may pinch your hands or ngers.
18. The equipment should not be used by persons weighing over 250 pounds.
19. The equipment should be used by only one person at a time.
20. The equipment is for consumer use only. It is not for use in public or semipublic facilities.
3RM-1
THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY: Allen Wrench (5mm)
Allen Wrench (5mm)
Wrench (13mm)
Center Beam
Extension Arm
Extension Arm
Pivot Connector
Shock
Rear
Support
Stabilizer
Cap
Seat
Left Handlebar
Right Handlebar
Front Cover
Front Support
Meter
Meter Post
Pedal
Front
Stabilizer
Left
Stand Cap
Warning Label
Pedal Strap
e
SAFETY INSTRUCTIONS
Exercise can present a health risk. Consult a physician before beginning any
exercise program with this equipment. If you feel faint or dizzy, discontinue
use of this equipment immediately. Serious body injury may occur if the
equipment is not assembled and used correctly, or not following the
instructions correctly. This is especially important if you are over the age of 35,
have never exercised before, are pregnant, or suer from any health problem.
This product is for home use only. Do not use in institutional or commercial
applications.
Keep others and pets away from the equipment when in use. Always make sure
all bolts and nuts are securely tightened prior to each use. Please follow through
all safety instructions in this manual.
This product contains a chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
WARNING
PARTS IDENTIFIER
PRODUCT PARTS DRAWING
RM-1 4
FRONT
BACK
PARTS LIST
RM-1 5
PART# PART NAME QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
73
44
45
46
47
Center Beam
Center Beam Cap
Seat Stopper
Rear Support
Stabilizer Cap
Stabilizer Pad
Threaded Support Plate
handlebar Support
Sensor Support Plate
Pivot Connector
Pivot Bushing
Bumper Knob
Locking Knob
Extension Arm
Exension Arm Bushin
Large Washer (M12)
Left Handlebar
Right Handlebar
Securing Cap
Foam Grip
Handlebar Cap
Shock
Support Plate
Front Cover
Sleeve
Front Support
Support Ring
Front Stabilizer
Left Stand Cap
Right Stand Cap
Meter Post
Pedal Shaft
Pedal Spacer
Pedal
Pedal Strap
Large Washer (M8)
Meter
Grommet
Extension Wire
Sensor Wire
Magnet
Seat
Seat Carriage
Roller
Round Plug (25mm)
Nut Cap (M10)
Screw, Round Head (M2.9 x 10mm)
1
1
4
1
1
1
3
1
1
1
2
2
2
2
4
2
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
4
2
2
4
RM-1 6
PART# PART NAME QTY
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Wave Washer (ø20 x ø23.5 x 0.5mm thick)
Screw, Round Head (M5 x 0.8 x 12mm)
Bolt, Round Head (M6 x 1 x 15mm)
Bolt, Button Head (M8 x 1.25 x 15mm)
Bolt, Button Head (M8 x 1.25 x 20mm)
Bolt, Button Head (M8 x 1.25 x 25mm)
Bolt, Button Head (M8 x 1.25 x 50mm)
Bolt, Hex Head (M8 x 1.25 x 30mm)
Bolt, Hex Head (M8 x 1.25 x 41mm)
Bolt, Hex Head (M10 x 1.5 x 120mm)
Washer (M6)
Washer (M8)
Washer (M10)
Spring Washer (M8)
Nylon Nut (M8 x 1.25)
Nylon Nut (M10 x 1.5)
Allen Wrench (5mm)
Wrench (13mm)
Owner’s Manual
Warning Label
Screw, Round Head (M3.5 x 15mm)
4
4
4
8
8
6
2
4
2
1
4
26
2
10
10
3
2
1
1
1
5
PARTS LIST
e
7
HARDWARE IDENTIFICATION CHART
RM-1
length
length
mm.
in.
INCHES
This chart is provided to help identify the fasteners used in the assembly process. Place the washers or
the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to
check the length of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat
heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.
After unpacking the unit, open the hardware bag and make sure that you have all the following
fasteners. Some fasteners may be already attached to the parts.
MILLIMETERS
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1/2 1/2 1/2 1/2 1/2 1/21 2 3 4 5 6
6 8 10 12
3/16" 1/4" 5/16" 3/8" 1/2"
Part No. and Description Qty
36 Large Washer (M8) 2
59 Washer (M8) 8
51 Bolt, Button Head (M8 x 1.25 x 15mm) 8
53 Bolt, Button Head (M8 x 1.25 x 25mm) 2
49 Screw, Round Head (M5 x 0.8 x 12mm) 2
62 Nylon Nut (M8 x 1.25) 2
8
ASSEMBLY INSTRUCTIONS
RM-1
Place all parts from the box in a cleared area and position them on the oor in front of you. Remove
all packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed. Read each step carefully before beginning.
STEP 1
Lay the Main Frame Assembly on the oor as shown in the illustration. Now refer to inset drawing A. Make
sure the Key Rib in the STABILIZER CAP(5) aligns with the slot in the REAR SUPPORT(4), then press the
STABILIZER CAP(5) onto the REAR SUPPORT(4). Turn the Main Frame Assembly to the normal upright
position and make sure the STABILIZER PAD(6) is secured to the STABILIZER CAP(5).
Key Rib
A.
9
ASSEMBLY INSTRUCTIONS
RM-1
STEP 2
Insert the Bracket on FRONT STABILIZER(28) into the FRONT SUPPORT(26). Attach the METER POST(31)
to the FRONT SUPPORT(28), then bolt the METER POST(31), FRONT SUPPORT(26), and FRONT
STABILIZER(28) together with BUTTON HEAD BOLTS(M8x1.25x15mm)(51) and WASHERS(M8)(59).
Please do not tighten any of these bolts until all six bolts are attached.
NOTE: Be careful not to damage the EXTENSION WIRE(38) when assembling the METER POST(32).
STEP 3
Connect the EXTENSION WIRE(39) to the SENSOR WIRE(40).
10
ASSEMBLY INSTRUCTIONS
RM-1
STEP 4
Insert the PEDAL SHAFT(32) through holes located on the METER POST(31). Place a PEDAL SPACER(33)
and a PEDAL(34) onto each end of the PEDAL SHAFT(32) and slide them toward the METER POST(31).
Then secure the PEDALS(34) with BUTTON HEAD BOLTS(M8x1.25x15mm)(51) and LARGE WASHERS
(M8)(36) at both ends of the PEDAL SHAFT(32). You need to use two Allen Wrenches to tighten the
BUTTON HEAD BOLTS(M8x1.25x15mm)(51) at both ends of the PEDAL SHAFT(32) at the same time.
STEP 5
Remove the LOCKING KNOBS(13) from the PIVOT CONNECTOR(10).
Inhaltsverzeichnis
Andere Harvil Heim-Fitnessstudio Handbücher
Beliebte Heim-Fitnessstudio Handbücher anderer Marken
Horizon Fitness
Horizon Fitness OXFORD 6 Bedienungsanleitung
Energetics
Energetics Multi Trainer 5.1 Bedienungsanleitung
Matrix
Matrix MG-PL Series Bedienungsanleitung
Reebok
Reebok Tbr2i Bedienungs- und Wartungshandbuch
Weider
Weider 8300 Hard Drive Bedienungsanleitung
Pure Fitness
Pure Fitness 8526HE Bedienungsanleitung
