Havis-Shields Dome Light KR-DL Bedienungsanleitung
Dome Light KR-DL
Installation Instructions
Warning: Please read all instructions and warnings prior to installation of the Dome Light.
TOOLS REQUIRED:
Phillips Screw Driver
Wire Cutter
HARDWARE: (Supplied in Kit)
Qty. Description Qty. Description
2 #8-32 Machine Screw 2 #8 Fender Washer
2 #8 KEP Nut 2 #8 Sheet Metal Screw
INSTALLATION:
1. Mounting:
• A drill template is provided on the back of this instruction sheet. Detach the
template, position it on the desired location for installation, and mark drill locations.
Caution: Before drilling holes, ensure that the mounting surfaces are clear and that the
screws will not damage the internal parts of the vehicle.
Caution: Ensure that the Dome Light is installed in areas recommended by the vehicle
manufacturer.
• Drill the mounting holes.
• Connect the power leads using wire splices.
• Remove the template prior to installing the fixture. Secure the base of the fixture in
position using the supplied machine screws, washers, and nuts.
Caution: Thread forming screws are supplied for alternate installations. If the fixture needs to
be mounted with thread forming screws, please note that it may not always be sufficiently
secured. It is at the sole discretion of the installer to determine the suitability of using thread-
forming screws for a particular installation.
• The fixture is supplied with two clear lenses and two red lenses. Install two lenses
suitable for the vehicle.
• Test the fixture for proper operation.
KR-DL-INST-9-05
Caution: The Dome Light uses bulbs which can be VERY HOT! Do not touch a bare bulb
when it is lighted.
2. Operation:
• The fixture has two switches, which control each of the two lamps independently.
• Pressing each switch once turns the lamp on, and pressing it a second time turns the
lamp off.
3. Troubleshooting:
• In the event of improper operation, first check that the switches are turned on.
• Second, check the each bulb and replace if burned out.
• Third, check the fuse (if installed) and replace if necessary.
• Finally, use a voltmeter to ensure that the fixture is receiving adequate power. The
light requires nominally 12 VDC for correct operation. Voltage must be measured
using the fixture power leads, not the vehicle chassis. Correct any faults found.
REPLACEMENT PARTS:
Part # Description
KRM89073-17 Automotive Type 918 Replacement Lamp, 7 Watt, 12 VDC
TEMPLATE: ∅0.17 (11/64” Drill)
Mounting Holes
5-5/16”
Cli
p
Here
Cli
p
Here
Wirewa
y
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Havis-Shields Arbeitsleuchte Handbücher
Havis-Shields
Havis-Shields Magnafire 3000 Bedienungsanleitung
Havis-Shields
Havis-Shields C-MAP-S Bedienungsanleitung
Havis-Shields
Havis-Shields LED Gooseneck Map Light Bedienungsanleitung
Havis-Shields
Havis-Shields Magnafire 5000 Bedienungsanleitung
Havis-Shields
Havis-Shields Roof Mounted Load Light KK-RLL Bedienungsanleitung
Beliebte Arbeitsleuchte Handbücher anderer Marken
PowerSmith
PowerSmith PWLD080T Bedienungsanleitung
MaxLite
MaxLite 73683 Bedienungsanleitung
Heitronic
Heitronic Trend 27867 Bedienungsanleitung
Monzana
Monzana Gore MZCL10 Bedienungsanleitung
EINHELL
EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung
Bayco
Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung