Havis-Shields LED Gooseneck Map Light Bedienungsanleitung
LED Gooseneck Map Light
Installation Instructions
Warning: Please read all instructions and warnings prior to installation of the LED Gooseneck Map Light.
TOOLS REQUIRED:
Phillips Screw Driver
Wire Cutter/Stripper
HARDWARE: (Supplied in Kit)
Qty. Description Qty. Description
2 #6 Machine Screw 2 #6 Split Lock Washer
2 #6 Thread Forming Screw 2 #6 Flat Washer
INSTALLATION:
1. Mounting:
• A drill template is provided on the back of this instruction sheet. Detach the
template, position it on the desired location for installation, and mark drill locations.
Caution: Before drilling holes, ensure that the mounting surfaces are clear and that the
screws will not damage the internal parts of the console or vehicle.
Caution: Ensure that the Gooseneck Map Light is installed in areas recommended by the
vehicle manufacturer—outside of the airbag zone.
• Drill the mounting holes.
• Remove the template prior to installing the fixture. Secure the base of the fixture in
position using the supplied machine screws and washers.
• The supplied super clip may be used to secure the gooseneck in position if desired.
Caution: Thread forming screws are supplied for alternate installations requiring the fixture to
be mounted from above. If the fixture needs to be disassembled for such installation, please
note that this will void your warranty.
2. Wiring:
• Connect the black lead to negative (ground.)
• Connect the red lead to hot (power.)
Note: It is recommended to install an in-line fuse holder and 1 Amp fuse on the red (hot) lead.
• Test the light for proper operation.
H:\Cons\Misc\LED-Map-Light-Inst-8-08.doc
3. Operation:
• Power is supplied through a three-position switch. The center position is “off,” and
the up and down positions provide red or white light.
4. Troubleshooting:
• Use a voltmeter to ensure that the fixture is receiving adequate power. The light
requires nominally 12 VDC for correct operation. Correct any faults found.
• A bad ground connection can cause improper operation. Use a negative wire instead
of connecting power to the vehicle chassis to avoid any ground issues.
• The light will not be able to turn on if polarity is reversed.
TEMPLATE:
∅0.16 (5/32” Drill)
Mounting Holes
∅0.50 (1/2” Drill)
Wireway
1-23/3221/32
Cli
p
Here
Cli
p
Here
To Switch,
Circuit and
LEDs
+12 VDC
Power 1A Fuse
(Recommended)
User-Supplied
Connector
(Optional)
Ground
HOT - RED
COMMON - BLACK
Note:
Fuse, fuse holder, and connector are
not supplied by Havis-Shields.
Inhaltsverzeichnis
Andere Havis-Shields Arbeitsleuchte Handbücher
Havis-Shields
Havis-Shields Roof Mounted Load Light KK-RLL Bedienungsanleitung
Havis-Shields
Havis-Shields Magnafire 3000 Bedienungsanleitung
Havis-Shields
Havis-Shields C-MAP-S Bedienungsanleitung
Havis-Shields
Havis-Shields Dome Light KR-DL Bedienungsanleitung
Havis-Shields
Havis-Shields Magnafire 5000 Bedienungsanleitung
Beliebte Arbeitsleuchte Handbücher anderer Marken
PowerSmith
PowerSmith PWLD080T Bedienungsanleitung
MaxLite
MaxLite 73683 Bedienungsanleitung
Heitronic
Heitronic Trend 27867 Bedienungsanleitung
Monzana
Monzana Gore MZCL10 Bedienungsanleitung
EINHELL
EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung
Bayco
Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung