HAWK ENTERPRISES REDTAIL2014 Bedienungsanleitung

HAWK ENTERPRISES 2902 Park Six Court, Elkhart, IN 46514 (574) 294-1910 (888) 289-4295

www.hawkenterprises.com

Operation Care Service

HAWK Red Tail 2014

Surface Prep Orbital Floor Machine

Surface Preparaon, Scrubbing, Reﬁnishing

HAWK

ENTERPRISES

Speciﬁcaaons

Model# REDTAIL 2014

Part# F-REDTAIL-2014

Pad Size 20” x 14”

Pad Speed 1725 RPM

Weight 112 lbs.

Pad Pressure 0.4 lbs/in

Motor 1.0 HP, 56 frame, TEFC, dual capacitor AC motor

Power Source 115-230V, 50/60 Hz power

Power Cord 50 . 14-3 JT power cord with molded plug

Amp Draw 7.8 Amp

Drive System Essentric balanced orbital drive

Vibraon Isol tor (4) primary, (6) secondary

dB Rang 66 - Meets GS42 standard.

SERVICE INFORMATION

To obtain consistent performance over the life of your equipment, read though these

instructions and save them for future reference. If you require service, contact the

dealer from which the machine was purchased or an authorized service station.

Always refer to your limited Warranty for complete service information.

The model, type, and serial number are indicated on the data plate on the side of the

handle. From prompt and complete service, refer to these numbers when

inquiring about service.

Write the model and serial number of your

unit in the space provided. Refer to the

data plate on unit.

SERIAL # MODEL #

Retain this owners manual for future reference.

SERIAL NO. MODEL

VOLTS

MOTOR

PHASE

AMPS

H.P.

Service Information .................................................................................................2

Machine Specications ............................................................................................3

Features....................................................................................................................3

Important Safety Instructions...................................................................................4

Grounding Instructions ........................................................................................5-6

Operations ...............................................................................................................7

Guidelines For Operations.......................................................................................7

Controls...............................................................................................................7

Adjustments.........................................................................................................8

Cord Storage .......................................................................................................8

Clean Up And Storage .............................................................................................8

Limited Warranty....................................................................................Back Cover

Model # REDTAIL2014

Part # F-REDTAIL-2014

Pad Size 20” X 14”

Pad Driver Type Combination Pad

Holder/Diamond Pad Driver

Power Source 115V 60Hz

Motor/HP 1.0 HP TEFC

1740 Rpm

Amp Draw 7.8

Vibration

Compensator 1.25 Inches

Cord 50’14-3 SJT

Pad Pressure (lbs/in2)*** .40

Total Weight ** 162

Shipping Weight 198

**Weight is calculated without the power cord

***Pad pressure does not include the weight of the power

cord.

Specications subject to change without notice.

Features

• Twin (dual) capacitor 56-frame TEFC

(totally enclosed fan cooled) motor

keeps out dirt and dust for longer motor

life.

• Extra heavy duty spring steel cord

strain relief with a 50’14-3 power cord

• Low current draw

• Thumb-operated safety switch

• Negative pressure on/off switch

• Dual steel operating triggers for left- or

right-hand operation

• One-piece industrial powder coated

heavy duty steel handle for optimum

durability

• Welded frame for rugged, reliable

performance

• Non-marking, 2x6” ball bearing

wheels

• Multiple position handle adjustment

for operator comfort and safety

• Comfortable vinyl handle grips for

ease of use

• Full wraparound dust skirt

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

WARNING:

ELECTRIC SHOCK CAN CAUSE SERIOUS

INJURY OR BE FATAL. PLEASE READ THE

FOLLOWING INSTRUCTIONS ON THE USE

AND OPERATIONS OF FLOOR FINISHING

MACHINES.

• Your TigerHawk is equipped with a safety switch lock and power switch triggers de-

signed for your safety. Do not attempt to bypass or defeat the safety switch lock. Never

use any device to lock the power switch triggers in the “ON” position.

• Do not leave the TigerHawk plugged in. Turn off the switch and unplug the electrical

cord when not in use and before servicing or changing the brushes or pads.

• Do not allow the machine to be used as a toy. Close attention is necessary when used

near children. Do not leave the machine connected to an electrical outlet unattended.

• Use only as described in this manual. Use only manufacturer’s recommended attach-

ments.

• Do not use with a damaged cord or plug. If the machine is not working as it should, has

been dropped, damaged, or left outdoors, return it to a service center before using.

• Use care to keep the electrical supply cord around sharp edges or corners. Keep the cord

away from the heated surfaces.

• Connect to properly grounded (3-wire) outlet only. Refer to Grounding Instructions,

Page 5-6.

• Do not use extension cords or outlets with inadequate current carrying capacity.

• Turn off all controls before unplugging.

• Do not unplug by pulling on the cord. To unplug, grasp the plug and pull.

• Do not handle the plug or TigerHawk with wet hands.

• Wind the cord no tighter than is necessary to retain it during storage. Refer to Cord

Storage, Page 8.

• Use extra care when working on or near stairs.

• Do not use in conjunction with ammable or combustible liquids such as gasoline, or

use in areas where explosive vapor or dust may be present.

• Store your TigerHawk indoors in a cool, dry area.

• Keep your work area well lighted.

• WARNING: To avoid electrical shock, use indoor only.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or break down, grounding provides a

path of least resistance for electric current to reduce the risk of electric shock. This appliance is

equipped with a cord that has an equipment-grounding conductor and grounding plug. The plug

must be plugged into an appropriate outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

FOR FLOOR FINISHING MACHINES RATED LESS THAN

150 VOLTS

Improper connection of an equipment grounding conductor can result in risk of electric shock.

Check with a qualied electrician or service person if you are in doubt as to whether the outlet is

properly grounded. Do not modify the plug provided with the appliance. If it will not t the outlet,

have a proper outlet installed by a qualied electrician. This appliance is for use on a nominal 120

volt circuit and has a grounding plug that looks like the plug illustrated in Figure 1.

A temporary adapter which looks like the adapter illustrated in Figure 2 may be used to connect this

plug to a two pole receptacle, as shown, if a properly grounded outlet is not available. The temporary

adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a qualied

electrician. The green colored rigid ear, lug, or the like extending from the adapter must be connected

to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it

must be held in place by metal screw.

FOR FLOOR FINISHING MACHINES RATED 150-220 VOLTS:

If the machine is provided with an attachment plug cap as shown in Figure 3, it is intended for use on

a 240 volt (nominal) circuit. No adapter is available for this cap.

WARNING:

RISK OF EXPLOSION. FLOOR SANDING

MACHINE CAN RESULT INAN EXPLOSIVE

MIXTURE OF FINE DUSTAND AIR. USE FLOOR

SANDING MACHINE ONLY IN A

WELL-VENTILATED AREA, FREE FROM ANY

FLAME OR MATCH

WARNING:

DO NOT USE GROUNDING

ADAPTERS ON TIGERHAWKS IN

CANADA. CHECK WITH CANADIAN CODE

FOR PROPER EQUIPMENT USAGE.

IMPROPER USE OF GROUND ADAPTORS CAN

CAUSE SERIOUS INJURY, FIRE, OR BE FATAL.

Grounding Instructions (Continued)

CONTROLS

TO TURN THE MACHINE ON

The operating handle must be lowered and locked to the proper operating position before switching the

machine ON. Place both hands rmly on the handle grips with your ngers around the power triggers.

Do NOT apply pressure on the triggers before the safety switch lock is disengaged.

Disengage the safety switch lock by pushing it forward with one thumb. Then, while holding the safety

switch lock in the disengaged position, squeeze the power triggers toward the handle grips and return

your thumb to the handle grip.

To stop the machine, simply release the triggers. The safety switch lock will automatically return to the

engaged position.

GUIDELINES FOR OPERATION

• Your RedTail is a very sensitive, powerful unit. When in operation, it should be guided gradually and

smoothly without sudden or rough motions. You will want to practice with your machine on a smooth

surface until you have experience in operating it.

• For ease of operation, always keep the brush or pad surface level, balanced, and at on the oor at all

times.

• Always adjust the operating handle to a comfortable height at which the brush or pad surface is

balanced before starting the machine. (See Handle Adjustment Page 4)

• Your RedTail will operate differently on various surfaces. For example, there will be much more

resistance when the machine is used on a rough surface, than when it is used on a smooth surface. The

operator should be prepared to adjust for these differences.

• BEGIN OPERATING THE REDTAIL

•

• WITH THE PAD SURFACE LEVEL, BALANCED AND FLAT ON THE FLOOR.

• To move the machine to the right, turn the unit to the right.

• To move the machine to the left, turn the unit to the left.

• To move the machine forward or backward, keep the brush or pad at on the oor and push or pull the

machine in the desired direction.

Push forward to disen-

gage safety switch lock.

CLEANUPAND STORAGE

After being used, your TigerHawk can be wiped clean with a soft damp cloth and should be

stored in a clean, dry place.

ADJUSTMENTS

HANDLE ADJUSTMENT

The handle can be adjusted to any desired work position by simply pulling on the pull

pin and move the handle to the desired position. Firmly push the pull pin back into the

adjustment holes. This will lock the handle in position.

Figure 5

Pull Knob

CORD STORAGE

When not in use, loosely coil the power cord and hang on

the handle.

Inhaltsverzeichnis

Andere HAWK ENTERPRISES Bodenreinigungsmaschine Handbücher

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513HD Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP 1517 HD Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES TigerHawk 1410 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES TH-2014 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-2S Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1517-180TEXHD MERLIN Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513XHD Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES EYAS.5 HP series Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-XHD2S Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-TEXHD Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES MINI-VACTOR Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-1500 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung