Hayward GLX-PCB-HPC-4 Bedienungsanleitung

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

GLX-PCB-HPC-4

Main Printed Circuit Board (PCB) for ECOMMAND 4

Compatibility

The GLX-PCB-HPC-4 is a replacement main board for the ECOMMAND 4 (HPC-4) pool control. This circuit

board is compatible with all ECOMMAND 4 models including HPC-4, HPC-4-ACT, HPC-4-RC, and HPC-4-ACT-

RC.

Circuit Board Replacement

1. Record the System Settings: The Conﬁguration, Timers, and Settings menus contain all of the informa-

tion regarding how the ECOMMAND 4 is programmed to operate a speciﬁc pool system. This information

is stored on the main PCB and it is very important that all of this information gets transferred from the old

PCB to the new PCB. Record all programming information (Conﬁguration menu, Timers menu, and Set-

tings menu) before attempting to replace the board.

2. Remove the old board: Make sure that ALL circuit breakers are OFF prior to PCB removal.

a. Remove metal panel to expose the local display and circuit board.

b. Remove the local display by pulling up and unplugging cable.

c. Unplug the sensor and display communication terminal blocks from the old PCB - you don’t need to

disconnect/reconnect individual wires.

d. Remove transformer wires and any other wires that are connected to the old board, making note of

their locations.

e. Remove the board by loosening the 2 mounting screws and sliding the board forward and up. When

the board comes loose from the enclosure, pull it up and out.

3. Install the new GLX-PCB-HPC-4 circuit board:

a. Install the new board using the two mounting screws.

b. The locations of the transformer lugs may be different from the old board.

c. Connect the remaining wires including the sensor and display communication terminal blocks onto

the new circuit board. If there are any questions about wiring locations, refer to your Installation

manual.

d. Plug in and install the local display.

e. Replace metal panel.

092449 RevB

Hayward Industries

400 Connell Drive, Suite 6100

Berkeley Heights, NJ 07922

Phone: (908) 355-7995

www.hayward.com

USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS

4. Turn power on and initialize the new PCB:

a. Turn power back on to the Pro Logic and conﬁrm that the board is working properly.

b. To initialize the new PCB, hold down the Menu, Lights and Aux2 buttons at the same time until you

hear a series of beeps. The GLX-PCB-HPC-4 is now initialized and ready to conﬁgure.

5. Turn power on and reset Conﬁguration to Default:

a. Reset all of the Conﬁguration parameters to their Default values using the following instructions:

b. Enter the prior programming information using the Conﬁguration, Timers and Settings menus.

Pool/Spa

Filter

Lights

Service

Aux 1

Aux 2

Lights

button

Aux 2

button

Configurat ion

Menu-Unlocked

Configurat ion

Menu-Locked

Press repeatedly until “Configuration Menu” is displayed

Press left arrow button

Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock

Reset Config. t o

Default Press +

Are you sure?

+ t o proceed

Config. reset

Confirmed

Initiate reset of all configuration parameters

Reset all configuration parameters

Move to previous/next configuration menu (config. not reset)

Move to previous/next menu (config. not reset)

Move to previous/next configuration menu

Hayward Industries

400 Connell Drive, Suite 6100

Berkeley Heights, NJ 07922

Phone: (908) 355-7995

www.hayward.com

Inhaltsverzeichnis

Andere Hayward Controller Handbücher

Hayward

Hayward HCC 4000 Bedienungsanleitung

Hayward

Hayward CAT-1000-ORP Bedienungsanleitung

Hayward

Hayward VS Omni Bedienungsanleitung

Hayward

Hayward E-Command® 4 Bedienungsanleitung

Hayward

Hayward ColorLogic LKCUS1100 Bedienungsanleitung

Hayward

Hayward OmniPL HLBPRO4SW Bedienungsanleitung

Hayward

Hayward HLXPLCONTROL Bedienungsanleitung

Hayward

Hayward Aqua Solar Technisches Datenblatt

Hayward

Hayward Aqua Plus® Bedienungsanleitung

Hayward

Hayward Aqua Plus® Bedienungsanleitung

Hayward

Hayward CAT 1000 Bedienungsanleitung

Hayward

Hayward OmniPL Retrofit Kit Bedienungsanleitung

Hayward

Hayward HCC 2000 Bedienungsanleitung

Hayward

Hayward HCC 1000 Bedienungsanleitung

Hayward

Hayward HRSN3 series Handbuch

Hayward

Hayward E-Command® 4 Bedienungsanleitung

Hayward

Hayward Aqua Plus® Bedienungsanleitung

Hayward

Hayward CAT 5000 Bedienungsanleitung

Hayward

Hayward ECP3 Series Handbuch

Hayward

Hayward Pool Rx LT Bedienungsanleitung

Hayward

Hayward HRSN2 series Handbuch

Hayward

Hayward Aqua Solar GL-235 Technisches Datenblatt

Hayward

Hayward EAU129 Series Handbuch

Hayward

Hayward HLXPLCONTROL Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung