Hayward AQR100 Bedienungsanleitung

Andere Handbücher für AQR100

2

Dieses Handbuch passt für folgende Modelle

1

Andere Hayward Controller Handbücher

Hayward

Hayward OmniLogic HTG-OL150c Administratorhandbuch

Hayward

Hayward CAT 5000 Bedienungsanleitung

Hayward

Hayward ECP3 Series Handbuch

Hayward

Hayward HCC 1000 Bedienungsanleitung

Hayward

Hayward GVA-24 Bedienungsanleitung

Hayward

Hayward Aqua Solar Technisches Datenblatt

Hayward

Hayward CAT-1000-ORP Bedienungsanleitung

Hayward

Hayward GLX-PCB-HPC-4 Bedienungsanleitung

Hayward

Hayward HRSN3 series Handbuch

Hayward

Hayward CAT 4000 Bedienungsanleitung

Hayward

Hayward HCC 4000 Bedienungsanleitung

Hayward

Hayward Aqua Solar GL-235 Technisches Datenblatt

Hayward

Hayward HLXPLCONTROL Bedienungsanleitung

Hayward

Hayward HRSN6 series Handbuch

Hayward

Hayward HLXPLCONTROL Bedienungsanleitung

Hayward

Hayward ECP8 Series Bedienungsanleitung

Hayward

Hayward EAU129 Series Handbuch

Hayward

Hayward CAT-2000 Bedienungsanleitung

Hayward

Hayward E-Command® 4 Bedienungsanleitung

Hayward

Hayward HRSN2 series Handbuch

Hayward

Hayward ColorLogic LKCUS1100 Bedienungsanleitung

Hayward

Hayward E-Command® 4 Bedienungsanleitung

Hayward

Hayward OmniPL Retrofit Kit Bedienungsanleitung

Hayward

Hayward Aqua Plus® Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

Hayward Pool Products

620 Division Street, Elizabeth NJ 07207

Phone (908)-355-7995

www.hayward.com

AQR100

Replacement PCB for AQR100

Installation Manual

GLXAQR100PCB

Contents

Description............................1

Installation............................1

092004 RevA

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Description

The GLXAQR100PCB is a replacement printed circuit board (PCB) for the AQR100 chlorine genera-

tor only.

Installation

DANGER of Death, Injury or Property Damage if procedure not followed. This component

connects to the main circuit and chlorinator cell inside of the AQR100 enclosure. Separating the

enclosure is required. Power to the AQR100 MUST be shut off before the enclosure is separated.

1. Completely remove power to the AQR100.

2. Remove the AQR100 from the mounted surface.

3 Remove the 10 stainless steel screws from the back of the AQR100.

4. As you carefully separate the enclosure, reach in and remove the ribbon cable connector.

After the cable has been disconnected, remove the front half of the enclosure and put it

aside.

Remove the 10

fasteners shown

using a #2 Phillips

head screwdriver.

Pull straight up on the

connector to remove

the ribbon cable before

fully separating the

enclosure.

1

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

5. Looking down into the enclosure. Locate and remove the two connectors from the PCB as

shown.

6. There is a green wire that is connected to the PCB as shown below. Pull up on this wire to

disconnect it.

Separate this connector by

pinching the two outer tabs and

pulling up.

Pull straight up to remove the green conductor.

Separate this connector by

pushing down on the top lever

and pulling apart.

7. You can now remove the 4 Phillips head screws that fasten the PCB to the enclosure and then

remove the PCB.

8. To install the new PCB, reverse the previous steps.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

2

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

2

For further information or consumer

technical support, visit our website at

www.hayward.com

Hayward is a registered trademark and AQR100 is

a trademark of Hayward Industries, Inc. © 2019 Hayward Industries, Inc.

All other trademarks not owned by Hayward are the property of their respective owners.

Hayward is not in any way afﬁliated with or endorsed by those third parties.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS