Hayward HLPMPCONV Bedienungsanleitung

Hayward Industries

400 Connell Drive, Suite 6100

Berkeley Heights, NJ 07922

Phone: (908) 355-7995

www.hayward.com

Omni Controls

VSP Communication Board for Omni Controls

Installation Manual

HLPMPCONV

Contents

Overview................................1

Installation.............................1

Operation..............................5

092757 RevA

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Overview

The HLPMPCONV is a communication board bundled with a cable and enclosure. The HLPMPCONV

will allow full control of up to 3 Pentair variable speed pumps (VSPs) by Omni Control products. The

Omni Control can turn the pump on and off as well as vary speeds based on schedules and speed

settings.

Install and setup the pump for remote control according to its included instructions. Install and wire

the HLPMPCONV according to the instructions in this manual. After installation is complete, your

Omni Control manual will explain how to conﬁgure and control the pump.

IMPORTANT: Before attempting this installation, completely disconnect power to the pump

and to the Omni Control.

Installation

Disconnect power to both the Omni Control and the pump(s) at the circuit breakers before instal-

lation.

Mounting the Enclosure

The enclosure will hold the communication board which is wired to both the Omni Control and the

Pentair pump. Find a suitable mounting location for the enclosure that will allow wire runs to both

the pump (using the Pentair communication cable) and the control (using the included 15' cable).

Use appropriate hardware to fasten the enclosure to the mounting surface.

Wiring

The HLPMPCONV will be wired to the Omni Control and the Pentair pump using two 4 position screw

terminal connectors. These connectors can be removed from the board (pull straight up) for more

convenient access. Do not attempt to install the board into the enclosure until wiring is complete.

Omni Control - Connect the included 15' 4 conductor communication cable from the Omni Con-

trol's low speed bus connector (refer to your Omni Control Installation manual for VSP connection) to

the left connector on the HLPMPCONV as shown on the top of page 2.

Pentair Pump - The Pentair pump communication cable (supplied with the pump) will only have 2

conductors and attaches to the right connector on the HLPMPCONV. Up to two pumps can be wired

to this single connector as shown on the top of page 2. For 3 pumps, use a jumper as shown at the

bottom of page 2.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

RedBlackWhite

Green

From Omni Control

Yellow

Green

From Pentair Pump(s)

VSP 2 VSP 3

12 AWG Wire to RS485 Connector

Electrical

Wire Nuts

VSP 1

Use a jumper for sys-

tems with 3 pumps

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Installing HLPMPCONV into the Enclosure

After wiring is complete, insert the HLPMPCONV into the enclosure as shown.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Wires are sandwiched at exit and open

end of foam strip should be ﬂush with

enclosure.

Routing wires through the wiring channel

Route the cables through the wiring channel and out the exit of the enclosure. Sandwich the cables

at the exit point using one of the two tear out foam strips that are attached to the cover gasket. At

the exit, lay the cables in the center of the strip and fold the strip in half. Insert the folded side down

into the lowest section of the wiring channel as shown below. The open ends of the strip should be

ﬂush with the enclosure as shown.

Install the cover back on to the enclosure and power on the Omni Control and Pentair pump(s).

Proceed to Operation.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Operation

Update Firmware

Before attempting to operate your pump, your control's ﬁrmware must be updated. The control was

shipped with the version of ﬁrmware that was available at the time of release which may not sup-

port the HLPMPCONV. To ensure proper support, update to the latest ﬁrmware version by going to

https://www.hayward.com/ﬁrmware and downloading the latest Omni Control ﬁrmware ﬁles. Refer

to the Release Notes on that page for upgrade instructions. After the update is complete, the pump

can be conﬁgured.

Conﬁguration and Operation

The Pentair VSP will need to be conﬁgured using your Omni Control's Conﬁguration Wizard or Quick

Edit function. Refer to your Omni Control's Installation manual for information on how to conﬁgure

your pump. After conﬁguration, you can set the run time, schedules and speed of the pump. This is

explained in the Omni Control's Operation manual.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

For further information or consumer

technical support, visit our website at

www.hayward.com

Hayward is a registered trademark

All other trademarks not owned by Hayward are the property of their respective owners.

Hayward is not in any way afﬁliated with or endorsed by those third parties.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Inhaltsverzeichnis

Andere Hayward Controller Handbücher

Hayward

Hayward HRSN6 series Handbuch

Hayward

Hayward HCC 2000 Bedienungsanleitung

Hayward

Hayward HRSN2 series Handbuch

Hayward

Hayward CAT 5000 Bedienungsanleitung

Hayward

Hayward Aqua Plus® Bedienungsanleitung

Hayward

Hayward GLX-PCB-HPC-4 Bedienungsanleitung

Hayward

Hayward OmniPL Retrofit Kit Bedienungsanleitung

Hayward

Hayward Aqua Plus® Bedienungsanleitung

Hayward

Hayward HCC 4000 Bedienungsanleitung

Hayward

Hayward Aqua Solar Technisches Datenblatt

Hayward

Hayward Aqua Plus® Bedienungsanleitung

Hayward

Hayward CAT 4000 Bedienungsanleitung

Hayward

Hayward HLXPLCONTROL Bedienungsanleitung

Hayward

Hayward GVA-24 Bedienungsanleitung

Hayward

Hayward ColorLogic LKCUS1100 Bedienungsanleitung

Hayward

Hayward HRSN3 series Handbuch

Hayward

Hayward EAU129 Series Handbuch

Hayward

Hayward ECP8 Series Bedienungsanleitung

Hayward

Hayward Pool Rx LT Bedienungsanleitung

Hayward

Hayward CAT-1000-ORP Bedienungsanleitung

Hayward

Hayward HRSN2 series Handbuch

Hayward

Hayward HLXPLCONTROL Bedienungsanleitung

Hayward

Hayward Aqua Plus® Bedienungsanleitung

Hayward

Hayward OmniPL Retrofit Kit Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch