Hayward MakoShark 2 Bedienungsanleitung



ISRC9403RevB

KingShark2

Limited Warranty

MakoShark 2

KingShark

KingShark 2

KingShark 2 w/Remote

TigerShark 2

Tiger Shark 2 Plus

Your Hayward Pool Cleaner has been manufactured, tested and inspected in accordance with carefully specified

engineering requirements. It is warranted to be free from defects in materials and workmanship for a period of one year.

Coverage is provided to the original owner only and is not transferrable. This limited warranty includes both parts and labor

for the cleaners listed above. This warranty gives you specific legal rights. You may also have other rights, which vary from

state to state

EXCEPTIONS AND EXCLUSIONS FROM WARRANTY

Damage, malfunctions or other failures of the cleaner arising from improper electrical supply levels are excluded

from this warranty. Malfunctions, failure or damage of the cleaner caused by improper, unreasonable, or negligent use or

abuse by the consumer, are excluded from this warranty.

Any repair that is made on your cleaner during the warranty period by anyone other than an Authorized Hayward

Warranty Service Center (designated to perform such work) will void this warranty and other warranty rights you may have.

Filter cartridges and debris bags are not covered by this warranty

INSTRUCTIONS TO OBTAIN WARRANTY REPAIR

To obtain repair of your Hayward cleaner under this warranty, the following procedure must be followed:

• Locate and deliver the cleaner to the nearest Hayward Factory Authorized Warranty Service Center. Your Authorized

Hayward Warranty Service Center can be located by visiting www.haywardnet.com. You may also call 908-355-7955 to

locate you nearest authorized service center. Cost of transportation, if required, is at the sole expense of the owner. Proof

of purchase is required.

TERMS

If a warranty claim is made and the product delivered to an Authorized Hayward Warranty Service Center within the

warranty period, your Hayward cleaner will be repaired at no charge (parts & labor) to you. Listed warranty exclusions

apply.

No dealer, distributor, or other similar person has any authority to make any warranties or representations

concerning Hayward Pool Cleaner products or to extend this warranty beyond the express items contained herein.

Accordingly, Hayward Pool Products assumes no responsibility for any such warranties or representations beyond the

express items contained in this limited warranty.

WARRANTY REGISTRATION CARD

You can register your unit on-line by visiting www.Haywardnet.com or by filling out the registration

card and returning it to:

Hayward Industries

Attn Warranty Department

620 Division Street

Elizabeth, NJ 07207

KingShark2

CONTENTS

Safety Precautions ................................................................2

General Information...............................................................3

Motor Information ..................................................................4

Trouble Shooting ...................................................................5

Speciﬁcations ........................................................................7

Machine Assembly/Parts .......................................................8

Filter Assembly/Parts...........................................................10

Accessories .........................................................................11

Preventive Maintenance......................................................13

Parts Ordering Instructions..................................................14

Rev. 3/10

KingShark2

SAFETY PRECAUTIONS

The KingShark2 automatic swimming pool vacuum cleaner has been

manufactured with the highest degree of care and concern

for safety. We suggest the following safety precautions become part of your

pool safety regulations:

1. ALWAYS PUT THE MACHINE INTO THE WATER BEFORE CON-

NECTING IT TO THE ELECTRICAL OUTLET.

2. IT IS IMPORTANT FOR SWIMMERS’ SAFETY TO REMOVE

THE UNIT IMMEDIATELY FOLLOWING USE. THIS WILL ALSO

IMPROVE THE OPERATING LIFE OF YOUR KINGSHARK2.

3. BE CERTAIN THE MACHINE IS ONLY PLUGGED INTO A

GROUNDED ELECTRICAL OUTLET EQUIPPED WITH A

GROUND FAULT CIRCUIT INTERRUPTER.

4. DO NOT HANDLE MACHINE WHILE IT IS PLUGGED INTO THE

ELECTRICAL OUTLET.

5. DO NOT USE AN EXTENSION CORD. THIS COULD CREATE A

SAFETY HAZARD AND/OR DAMAGE YOUR UNIT.

6. ALWAYS STAY OUT OF THE POOL WHILE CLEANER IS IN

OPERATION.

7. NEVER ALLOW PLUG TO ENTER THE POOL.

8. DO NOT OPERATE THE MACHINE OUT OF WATER. THIS WILL

DAMAGE THE MOTOR SEAL AND VOID THE WARRANTY.

9. DO NOT DRAG THE MACHINE OUT OF THE POOL AGAINST

THE SIDE WALL. THIS COULD DAMAGE UNIT AND/OR YOUR

POOL WALL.

10. SOME POOLS HAVE A CORNER OR A CORNER STEP CON-

FIGURATION THAT MAY CAUSE THE UNIT TO “HANG-UP;”

THEREFORE, DO NOT LEAVE THE UNIT COMPLETELY

UNATTENDED FOR MORE THAN 1/2 HOUR. OCCASIONAL

OBSERVATION AND ATTENDANCE CAN ALSO REDUCE ANY

TENDENCY FOR THE CORD TO TWIST.

While the KingShark2 has been made to operate as safely as possible,

we suggest you exercise reasonable care in the handling of the vacuum and

inspect the electrical cord frequently for damage or wear, as with any other

electrical appliance. After use, remove the unit and rinse with fresh water and

remove any twists that may be present in the cord.

KingShark2

GENERAL INFORMATION

You have purchased the ﬁnest piece of equipment in the pool cleaner industry. If you

treat it as such, your KingShark2 automatic swimming pool vacuum cleaner will give you

years of satisfactory service. As a suggestion, the unit should be stored in the original

shipping container for safekeeping during the off season.

ADJUSTMENT

THERE IS ONE ADJUSTMENT THAT MAY BE NECESSARY FOR USE IN YOUR

POOL. PLEASE TAKE THE FEW MINUTES NECESSARY TO UNDERSTAND THIS

SIMPLE PROCEDURE:

The height of the sensor bar #3210 (Page 9, Key 2) is pre-set at the factory for

average pools. It may be necessary to readjust the height of the sensor bar for the

machine to operate satisfactorily in your pool.

In “Free Form” or “Bowl Shaped” pools, the sensor bar may have to be raised to a

higher setting to allow the machine to climb out of the deep end and clean up the

radius or slope as far as possible without the machine turning over.

Adjustment of the sensor bar #3210 (Page 9, Key 2) is made by loosening adjust-

ing arm bolts #2121 B (Page 9, Key D) located just ahead of the intake. With the

machine sitting on a level surface, loosen both adjusting arm bolts, and move sensor

bar to desired position. Make certain the sensor bar is parallel to the level surface

and retighten the adjusting arm.

It may be necessary to reset the sensor bar several times to ﬁnd the best position

for operation in your pool. Sensor bar should glide freely. This can be checked by

pushing back on the sensor bar which will activate the reversing arms.

OPERATING INSTRUCTIONS

Select nearest grounded outlet supply of 110/115/220/240 voltage.

CAUTION: avoid overloaded circuits as low or high voltage can damage your mo-

tor. A connected ground is most important. Plug into outlet. Observe machine as it

travels over bottom of pool.

Allow machine to travel around the pool until it is clean. Average 75' x 150' pool will

required approximately 4 hours. If the pool has a heavy accumulation of debris, it

may be necessary to clean the ﬁlter several times during the vacuuming period.

Upon completion of vacuuming the pool, allow the unit to travel to the shallow end

of the pool. Before it reaches the pool wall, turn power off, raise the unit by the white

nylon rope #1312, then remove the unit from the water by use of the handle. Allow

excess water from the ﬁlter to drain into the pool with the KingShark2 resting on the

edge or coping. Do not leave machine in water after disconnecting.

KingShark2

REMOVE THE UNIT IMMEDIATELY AFTER USE.

ALLOWING UNIT TO COOL IN WATER AFTER

RUNNING CAN CAUSE MOTOR SEAL DAMAGE.

To clean the cartridge ﬁlters #7807 (Page 10, Key 7) remove the ﬁlter housing

assembly #3400 (Page 10, Key 13) by removing the ﬁlter knob and releasing the

ﬁlter box.

Cleaning the ﬁlters after each use is an important part of maintaining your King-

Shark2. Clean ﬁlters will allow the machine to function most efﬁciently.

Disassemble the ﬁlter housing assembly #3400 (Page 10, Key l3) by removing the

four (4) ﬁlter knobs #3405 (Page 10, Key 3) The ﬁlter backplate #3416 (Page 10,

Key 10) and ﬁlter cartridges #7807 can then be removed.

Clean cartridges with a water hose using a pressure nozzle.

Use the KingShark2 on a regular basis to keep your pool clean.

MOTOR INFORMATION

The Motor in your KingShark2 has automatic overload protection. The overload

switch will protect the motor against burning out when an obstruction stops the

machine. When an obstruction stops the machine, UNPLUG THE CORD FROM

THE OUTLET and remove the unit from the pool. Turn the machine over and

with the aid of a long screw driver or needle-nose pliers, rotate the impeller and

dislodge any foreign object. All large objects should be removed from the pool

before the KingShark2 is put into operation.

KingShark2

TROUBLE SHOOTING

Where to set Sensor Bar

(Make adjustments in 1/4" Increments)

Machine fails to come out of deep end:

Raise sensor bar to allow the machine to climb the incline to shallow end.

Machine turns in circles and twists cord:

Sensor bar too high, hitting hood, or is not level.

Thread on reversing arm #2203 (Page 9, Key 16) is worn or stripped,

not allowing reversing mechanism to disengage.

Drive wheel broken.

Drive belt broken.

Is the unit being run in the pool for too great a length of time? Four

hours in operation in the larger pools should be sufﬁcient with not more

than a few twists in the cord, which should be straightened out after

each vacuuming.

Machine does not pick up:

Filter may be clogged and not permitting the ﬂow of water through the

ﬁlter cartridges, (clean ﬁlter cartridges).

Large object lodged in the intake or in the impeller housing (remove

object).

Machine does not move:

Not connected to live outlet, (check electrical source).

Object lodged in impeller, (remove object).

A short in the motor, (check the ground fault interrupter for tripping).

KingShark2

TROUBLE SHOOTING

Unit runs for short distance but stops. Check for overloaded circuit or

possible faulty motor. *Contact service center*

(DO NOT USE EXTENSION CORDS.)

Motor runs but unit becomes motionless (gear box worm is worn or the

drive pin is sheared).

Machine tips over backwards before sensing wall:

Improper sensor bar adjustment, (too high).

Cord too short for pool length. *Contact service center.*

You may need optional ﬂoat Part No. 7 (Page 13 ) call factory or local

dealer/service center.

Machine tips over before tripping or sensing wall:

Lower sensor bar to ensure it will engage and reverse unit.

KEEP SENSOR BAR LEVEL AT ALL TIMES!

KingShark2

SPECIFICATIONS

MOTOR:

Type ...................................................................... Submersible

Voltage .................................................................. 110/115 Volts ................................ 230/240 Volts

Frequency ............................................................. 60 Cycle ...........................................60/50 Cycle

Speed .................................................................... 1725 RPM ..........................................1425 RPM

Bearing .................................................................. Ball Bearings

Housing ................................................................. Aluminum Anodized

Motor Seals ........................................................... Double Lip Wave

Overload Protection .............................................. Thermal Overload

Electrical Cord .......................................................

#16 Wire Encased in Flotation Jacket; 150' in length

DRIVE:

Rear Wheel Drive ................................................. Planetary Gear System

Front Wheel Driven by .......................................... Continuous Belt

FILTER:

Type ...................................................................... Self Contained

Filter Media ........................................................... Corrugated Resin Impregnated Element

Porosity ................................................................. 50 Microns

Filter Area .............................................................. 40 Square Feet

Housing ................................................................. Molded Plastic

Gallons Circulated ................................................. 70-75 Per Minute/4200-4500 Per Hour

SHAFT and AXLE:

All parts such as axle, shafts, pins, fasteners, rods, etc., are corrosion resistant.

(KingShark2) SPECIFICATIONS WITHOUT SWIVEL

UNIT DIMENSIONS UNIT WEIGHT UNIT CORD LENGTH

Height 15 in. (38.1 cm) 86.5 lbs. (39.2 Kg) 150 ft. (45.7m)

Width 24 in. (60.0 cm)

Length 29 in. (73.6 cm)

(KingShark2) SPECIFICATIONS WITH SWIVEL

UNIT DIMENSIONS UNIT WEIGHT UNIT CORD LENGTH

Height 19.5 in. (49.5cm) 89.0 (40.5 Kg) 150 ft. (45.7m)

Width 24 in. (60.0 cm)

Length

29 in. (73.6 cm)

(KingShark2) W/BOX SPECIFICATIONS

UNIT BOX DIMENSIONS UNIT BOX WEIGHT UNIT BOX VOLUME

Height 19.5 in. (49.5 cm) 105 lbs. (47.6 Kg) 9.38 ft3 (.3m3)

W/Swivel 23.5 in. (59.7 cm)

Width 26.0 in. (66.0 cm) 109 lbs. (49.4 Kg) 11.31 ft3 (.36m3)

Length 32.0 in. (81.3 cm) w/optional Swivel w/optional Swivel

CADDY CART W/BOX SPECIFICATIONS

CART BOX DIMENSIONS CADDY CART WEIGHT CART BOX VOLUME

Height 12.5 in. (31.8 cm) 16.5 lbs. (7.5 Kg) 6.92 ft3(0.2m3)

Width 22.5 in. (57.2 cm) WITH BOX

Length 42.5 in. (107.0 cm) 29.0 lbs. (13.2 kg)

EXPORT ONLY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hayward Schwimmbadroboter Handbücher

Hayward

Hayward Viio Turbo AE5500 Bedienungsanleitung

Hayward

Hayward DYNA-SKIM SP1091LX Bedienungsanleitung

Hayward

Hayward TigerShark Bedienungsanleitung

Hayward

Hayward TriVac 700 Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Hayward

Hayward AquaVac 500 Bedienungsanleitung

Hayward

Hayward Navigator Bedienungsanleitung

Hayward

Hayward AquaVac 250 Bedienungsanleitung

Hayward

Hayward Navigator Bedienungsanleitung

Hayward

Hayward Navigator Bedienungsanleitung

Hayward

Hayward AquaNaut Bedienungsanleitung

Hayward

Hayward MAGIC CLEAN Bedienungsanleitung

Hayward

Hayward DV4000 Bedienungsanleitung

Hayward

Hayward Pool Vac XL™ Bedienungsanleitung

Hayward

Hayward NAVIGATOR POOLVAC V-Flex Bedienungsanleitung

Hayward

Hayward Pool Vac Ultra Bedienungsanleitung

Hayward

Hayward DV5000 Bedienungsanleitung

Hayward

Hayward AquaVac Bedienungsanleitung

Hayward

Hayward AquaVac 600 Bedienungsanleitung

Hayward

Hayward Navigator Pro Konfigurationshandbuch

Hayward

Hayward KingShark 2 Plus Bedienungsanleitung

Hayward

Hayward TigerShark Series Bedienungsanleitung

Hayward

Hayward SharkVAC XL Bedienungsanleitung

Hayward

Hayward AquaVac 250Li Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

Zodiac

Zodiac Baracuda G3 Bedienungsanleitung