Hayward TRX-20 Bedienungsanleitung

TRX-20

OWNERS MANUAL

2 WHEEL SUCTION-SIDE

POOL CLEANER

Hayward Pool Products Canada

2880 Plymouth Drive

Oakville, ON L6H 5R4

888.238.7665 / haywardpool.ca

TRX20-13

TRX-20

SELF ADJUSTING TURBINE VANES

The TRX-20 cleaner has the patented self-adjusting turbines, which maximize the power from the water ow. This turbine is similar to a

paddle wheel with blades that are adjustable. This feature allows the TRX-20 to still move at low suction and low pressure. In addition the

folding vanes of the turbine allow for the easy passage of larger debris through the cleaner.

STEERING SYSTEM

The 2x Suction TRX-20 has an internal programmed steering system, that causes the left wheel to periodically reverse, allowing the

TRX-20 to turn and then move into another direction. For the 2x Suction TRX-20 there are ve different programmed turns ranging from 90

to 450 degrees. This feature allows the TRX-20 to cover not only the deep end, but also the shallow end.

This steering system allows for the 2x Suction TRX-20 to travel 8 to 10 ft. before it turns. The TRX-20 cleans more in the shallow end than any

other cleaner and has no problem with uneven surfaces or strange shapes. It won’t stick in a corner, or get hung up by a main drain.

ROBUST TIRE TREADS

One look and you will see that the patented tire treads give the TRX-20 better climbing ability and obstacle maneuverability. The tires come

with tread wear markers that show you when to replace your tires. The front tires of the TRX-20 have humps (raised treads) that allow the

TRX-20 to overcome any reasonable obstacles such as the main drain and uneven surfaces. This makes the TRX-20 ideal for all pool

surfaces and shapes.

SELF-CLEANING SWIVEL

This is a feature that allows the TRX-20 to turn freely without interference from the hose due to debris buildup in the swivel hose cone. By

self-cleaning, the swivel prevents the hose from coiling.(Note: Sometimes with severe debris one needs to hold it under a water faucet

for cleaning).

ADJUSTABLE SKIRT

The TRX-20 has patented adjustable skirts that allow the cleaner to maintain optimal suction under the machine even when it encounters

obstacles. When the TRX-20 encounters an obstacle one (or more) of the skirts will lift up (adjust) over the obstacle while maintaining suction

under the cleaner.

TRX-20 works so that you can experience pool pleasure.

The rst thing you will notice when you look at the TRX-20 is that it is of highest quality.

The TRX-20 is robust and if maintained properly will result in many years of pool

cleaning. We use only the highest quality materials to ensure the best pool cleaning

products. The TRX-20 is proudly made in the usa. This cleaner was invented, designed

and built with years of experience in the pool industry. Every cleaner is tested to ensure the

nest quality.

The TRX-20 uses your existing pump and lter for power. The cleaners plug into either

your designated suction port or the skimmer.

THANK YOU FOR PURCHASING A TRX-20 CLEANER

FEATURES

INCLUDED WITH YOUR 2 WHEEL MODEL

INCLUDED COMPONENTS

IMPORTANT FACTS

1 2X Suction TRX-20

1 Regulator Valve and Water Gate

1 Hose Cone (Valve adapter)

9 Sections of hose

1 Leader Hose (with gray adapter)

2 Snap On Floats (already on hose)

2WHEEL

MODEL

REGULATOR

VALVE

WATER

GATE

HOSE CONE

( valve

adapter )

NORMAL HOSES (9 sections (2 Wheel) OR 11 sections (4Wheel))

one LEADER HOSE (note the grey cu)

AND

2 SNAP

ON FLOATS

• The TRX-20 should NEVER be used to remove plaster debris in new pools

• ALWAYS remove the TRX-20 before you chemically shock your pool

• ALWAYS remove the TRX-20 when swimmers enter the pool

• When removed from the pool, store the TRX-20 in a shaded safe area

• When removed from the pool DO NOT coil the hoses. THEY MUST BE STORED STRAIGHT

• The TRX-20 is NOT a toy and not intended for children

• Keep the TRX-20 and hoses away from chewing pets

• REMOVE the TRX-20 when performing backwash

• Remember Safety First

INCLUDED WITH YOUR 2 WHEEL MODEL

INCLUDED COMPONENTS

IMPORTANT FACTS

1 2X Suction TRX-20

1 Regulator Valve and Water Gate

1 Hose Cone (Valve adapter)

9 Sections of hose

1 Leader Hose (with gray adapter)

2 Snap On Floats (already on hose)

2WHEEL

MODEL

REGULATOR

VALVE

WATER

GATE

HOSE CONE

( valve

adapter )

NORMAL HOSES (9 sections (2 Wheel) OR 11 sections (4Wheel))

one LEADER HOSE (note the grey cu)

AND

2 SNAP

ON FLOATS

• The TRX-20 should NEVER be used to remove plaster debris in new pools

• ALWAYS remove the TRX-20 before you chemically shock your pool

• ALWAYS remove the TRX-20 when swimmers enter the pool

• When removed from the pool, store the TRX-20 in a shaded safe area

• When removed from the pool DO NOT coil the hoses. THEY MUST BE STORED STRAIGHT

• The TRX-20 is NOT a toy and not intended for children

• Keep the TRX-20 and hoses away from chewing pets

• REMOVE the TRX-20 when performing backwash

• Remember Safety First

STEP 1

1. Manually clean/vacuum your pool.

2. Perform a backwash, clean your ﬁlter,

skimmer baskets and pump basket.

3. Make sure your chemical balance is

correct. If not, now is the time to correct it. If you

chemically shock the pool, wait a day or two before continuing.

4. Point all your return ﬁttings downward.

Preparing your pool . . .

STEP 2 Connecting the hoses . . .

POINT RETURN FITTINGS DOWN

1. Take the Leader Hose (the one with the gray cuff) and attach the ﬂoat halves 24 inches

(60 cm) from the gray end. OR if you have the 2 snap on ﬂoats snap them at 20 to 25

inches from the gray cuff. This is the section of hose that attaches to the TRX-20

in Step 3. (We have already done this step for you).

2. Connect all the hoses (except the Leader Hose).

Connect male to female. If need be wet the hoses

for easier assembly. Now connect Leader Hose to

the end.

3. The connected hoses should be one to two

lengths longer than the furthest point from the

vacuum source (skimmer or wall ﬁtting).

LEADER HOSE

wall fitting

skimmer

One to two

lengths over

20-25" (50-60cm)

Gray Cu

2 Snap On

Floats

Float 1

Float 2

STEP 3

STEP 4

Getting your TRX-20 wet

Attaching the TRX-20

1. Connect the TRX-20 to the gray

cuff end on the leader hose.

2. Connect the opposite end (end of all the

hoses NOT gray) to the Adjustable

Regulator Valve. (This is needed for

skimmer applications and where there

is no 3-way valve for suction control).

See pg 6.

3. Connect the Adjustable Regulator Valve

to the Hose Cone (Valve Adapter) .

Lower the TRX-20 into the

water. While your pump is running,

take the end of the hose with the

Adjustable Regulator Valve (if you need it)

and hold it against one of the return ﬁttings

to expunge all of the air in the hose

and the TRX-20.

With the pump turned off, lower the

TRX-20 and then vertically push

the hose down into the water until the hose is

completely ﬁlled with water.

YOU DO NOT WANT ANY AIR TO REMAIN

IN THE HOSE AND THE TRX-20

AIR

push

hose

down

1. MAKE SURE THE POWER SUPPLY TO YOUR PUMP

IS OFF. SUCTION CAN BE VERY DANGEROUS!!!

Your cleaner came with both a Regulator Valve and a Water Gate.

2. If you are hooking into a skimmer tightly press the Regulator

Valve and the Hose Cone (Valve Adapter) end into the bottom

of your skimmer.

3. If you are hooking into a designated threaded suction

port/line (1 1/2”) then screw in the Water Gate and insert the

Regulator Valve OR insert the hose directly into the Water

Gate (you will probably have to adjust 3-way or ball valve

to get the correct performance when the Regulator Valve is not used).

3. Switch the pump power back ON.

Adjusting your TRX-20 (Adjusting your RegulatorValve) . . .

This valve regulates the suction so that the TRX-20 does not exceed the optimal

11-13 RPM(revolutions per minute). It does so by opening to bypass water when

necessary. This will ensure the best possible performance from your TRX-20.

The valve can be adjusted by:

1. Screwing the top in you will bypass less water, increasing the RPM (speed). If it is all

the way in and you still are below 11 RPM adjust the 3-way valve for more suction

and/or clean the lter. Remove the valve.

2. Screwing the top out you will bypass more, decreasing the RPM (speed). If it is screwd

all the way out and you still are above 14 RPM adjust the 3-way valve to give less suction.

Note: If the line you are hooked to (skimmer or inlet) has a 3-way valve or ball valve you

may have to adjust the 3-way valve or ball valve even if you are using the regulator valve.

MAX

MIN

MAX

MIN

1 2

Screw top in.

Bypass less water.

Speed cleaner up.

Unscrew top.

Bypass more water.

Slow cleaner down.

STEP 5

STEP 6

STEP 6 CONT’D. . .

1. The First Plumbing System: Single Line Suction.

This is when you have only one pipe

coming from your pool to your pump. If

this is the case there are no added

adjustments necessary, as the Automatic

Bypass Valve will regulate your

TRX-20. You are done with step 6!

2. The Second Plumbing System:

Adjustable three-way valve.

This is when you have a three-way valve

regulating ﬂow between the pump and the

main drain and the skimmer(s). This allows

you to adjust your system while ensuring

the best possible performance from your

TRX-20. (See next step).

3 WAY

VALVE

3. ADJUSTING WHEEL RPM (Optimal setting 11-14 RPM)

For the TRX-20 to run optimally the revolutions per minute should be between 11

and 13 (Note it will still clean as low as 8 RPM but will NOT climb walls).

While the TRX-20 is running take it by the leader hose so that the TRX-20

is just below the water. (KEEP THE CLEANER BELOW THE WATER LEVEL or else it will suck air).

Now count the number of revolutions made per minute by the RIGHT FRONT WHEEL by using

the hump (raised treads) as your marker. If it is between 11 and 13 RPM you are done.

If it is above 14 RPM adjust your three-way valve toward the main drain until the RPM drops

below 13. Once it has dropped below 14 RPM, you are done with Step 6.

If it is below 11 RPM adjust your three-way valve so that more water ﬂows through the

TRX-20 and skimmer until it is above 11 RPM. Once it is above 11 RPM, you are

done with Step 6.

NOTE: This is equivalent to 7 to 10 inches of mercury on a vacuum gauge. A vacuum gauge

is NOT included with the TRX-20

but is available at your local pool store.

Count RPM here

at the hump on the

RIGHT FRONT WHEEL

KEEP THE TRX-20 BELOW THE WATER LEVEL ! ! !

In general there are 2 plumbing styles that will determine

whether or not you need to make any adjustments.

FRONT

BACK

RPM=revolutions per minute

TRX-20 OBSTRUCTION

TURBINE VANES/BLADES

1. Rotate the right front wheel forward (the grill is the front) . If it wont move there is an obstruction. 2. Remove the

three screws that hold the Shroud ( Top Cover ). 3. Remove the Shroud. 4. Remove the turbine cover ( wiggle it up and off ).

5. Visually inspect the cleaner. Remove any debris found in the turbine, reduction gears, wheel hubs etc.. If you remove

the turbine vanes/blades please be sure to replace them correctly (see below). Replace the turbine cover and repeat

step one before placing the shroud back on, drop 3 screws into slots and secure.

1 2 3 4 5

The turbine vanes have to be placed in the turbine hub a certain

direction. We use the following mnemonic “ The turbine vanes

are like a wave breaking on the grill”. In the front of the unit

the vanes are convex ( like a mountain ) in the back they

are concave ( like a valley ). NOTE: The large elliptical end of

the vanes is placed into the turbine.

round

larger elliptical

(or turbine vane replacement)

BEFORE YOU DO ANYTHING, TURN THE PUMP OFF. SUCTION CAN BE DANGEROUS!!!

TIRES

The tires must be replaced when they are worn

down to the tread wear indicators. Note: if you cant

see them you are worn past them.

Please note: in order to replace

back tires you will ﬁrst have to remove

the shroud, then remove the wheel

and only then can you take the tires

off the wheel hub.

wear marks

(wear indicators)

TIRE REMOVAL & REPLACEMENT

1. Place the cleaner on a work surface. Using only

your hands (other tools may damage the cleaner)

simply fold the tire off from top to bottom.

Note: The front tires always have humps and the

back tires do not. To remove back tires you will need

to remove the shroud and the wheels (see next page).

2. To replace stretch the tire over the wheel hub (starting from one side and

folding it back on). Make sure it is on correctly. If need be do this closer to your

body for better leverage.

WHEEL OR BEARING REMOVAL & REPLACEMENT

SKIRT AND INLET REMOVAL & REPLACEMENT

1. Align a ﬂat head screwdriver into the slot at the center of the wheel and pop out the

clip holding the wheel. 2. Remove the the clip holding the wheel and place it aside.

3. Remove the wheel hub (Rim). 4. (Only if bearing is worn) Remove the bearing by pushing it from the outside

to the inside of the wheel. 5. (Only if bearing is worn) Replace the bearing by pushing the new bearing from

the inside of the wheel until it bottoms out. MAKE SURE THAT THE FLAT PARTS OF BOTH THE BEARING AND

WHEEL HUB ALIGN. 6. Place the wheel hub back onto the TRX-20 body and take the clip and clip it

back in. Make sure you hear it clip. If not you didnt align the ﬂat parts in step 5. When the unit is reassembled

turn the right front wheel (looking from behind) and make sure everything turns smoothly.

1. Turn the unit upside down and press with both ﬁnders on both sides

of the inlet. While pushing down pull up on the inlet. 2. Remove the inlet.

3. Once the inlet is removed you can remove any debris that is in the

turbine chamber. You can also remove and replace the skirt/bracket

assemeblies. One of the middle skirt/brackets can be easily pulled out.

Once one assembly is out you can slide the others out easily to replace.

4. Once any debris has been removed or the skirts have been replaced

replace the inlet. Note it can only be inserted in one direction and once it is

in it should clip on both sides. Note: if it does not clip in then you have it

the wrong way around (it is marked L and R).

123

BEFORE YOU DO ANYTHING, TURN THE PUMP OFF. SUCTION CAN BE DANGEROUS!!! 9

CLICK

(can also be used to remove debris)

L R

Inhaltsverzeichnis

Sprachen:

Andere Hayward Schwimmbadroboter Handbücher

Hayward

Hayward TRIVAC series Bedienungsanleitung

Hayward

Hayward ABOVE GROUND SERIES Bedienungsanleitung

Hayward

Hayward ABOVE GROUND SERIES Bedienungsanleitung

Hayward

Hayward Viio Turbo 5500TC Bedienungsanleitung

Hayward

Hayward ISSC100 Bedienungsanleitung

Hayward

Hayward AquaNaut Bedienungsanleitung

Hayward

Hayward TigerShark QC Bedienungsanleitung

Hayward

Hayward Navigator Pro Konfigurationshandbuch

Hayward

Hayward ISSC100AU Bedienungsanleitung

Hayward

Hayward Phantom 6000 Bedienungsanleitung

Hayward

Hayward AquaVac 500 Bedienungsanleitung

Hayward

Hayward DYNA-SKIM SP1091LX Bedienungsanleitung

Hayward

Hayward NAVIGATOR POOLVAC V-Flex Bedienungsanleitung

Hayward

Hayward AquaVac 250 Bedienungsanleitung

Hayward

Hayward DV4000 Bedienungsanleitung

Hayward

Hayward TigerShark Bedienungsanleitung

Hayward

Hayward Viio Turbo AE5500 Bedienungsanleitung

Hayward

Hayward TriVac 700 Bedienungsanleitung

Hayward

Hayward Phantom Turbo 6000 Bedienungsanleitung

Hayward

Hayward Navigator Bedienungsanleitung

Hayward

Hayward Pool Vac Classic Bedienungsanleitung

Hayward

Hayward Blu Bedienungsanleitung

Hayward

Hayward ABOVE GROUND SERIES Bedienungsanleitung

Hayward

Hayward Navigator V-Flex Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

Zodiac

Zodiac Baracuda G3 Bedienungsanleitung