Hayward ColorLogic® 4.0 Bedienungsanleitung

ColorLogic®4.0 Installation Guide

Table of Contents

Safety Precautions Page 1

Overview Page 2

Program Table Page 3

Network Module Installation Page 4

Wiring Lights Pages 5-6

Configuring Lights Page 7

Resetting Lights To Default Page 11

Auxiliary Configuration Page 12

Auxiliary Programming Page 13

Light Show Programming Pages 14-15

Fixed Color Programming Pages 16-17

Troubleshooting Pages 18-20

FAQ’s Pages 21-23

Wiring Diagrams Pages 24-26

Safety Precautions

Page 1

Hazardous voltage can shock, burn, cause serious injury and or death. To reduce the risk of

electrocution and or electric shock hazards:

•Ground Fault Circuit protection must be used in the circuit, however, all electrical wiring

MUST be in conformance with all applicable local codes, regulations, and the National

Electric Code (NEC).

•Replace damaged wiring immediately

•Reference NEC codes for all wiring standards including, but not limited to, grounding,

bonding and other general wiring procedures.

•Networked ColorLogic Lights and related electrical connections are receiving electrical power

at all times, even when the lights are OFF! Turn off power at the main breaker before

servicing ColorLogic lights.

Warning !

Compatibility

•The AQL-COLOR-MODHV is compatible with all Goldline Controls Pro Logic PS controls

operating with software version 4.00 or greater and whose enclosures provide a cutout for

installation.

•The ColorLogic Network Module will only operate with Generation 4 or later Hayward

ColorLogic 120VAC pool/spa light(s).

Description

•The ColorLogic Network Module is used with the Pro Logic to fully control the color, speed,

motion and brightness of pre-set light shows in a compatible Hayward ColorLogic pool/spa

light(s). After installing the ColorLogic Network Module and enabling the function in the Pro

Logic, the user can program various parameters to fully customize their pool/spa light(s)

operation.

•The ColorLogic Network Module can be used to control up to 32 pool or spa lights

simultaneously. This method of control features 2 user defined programs; five fixed colors

and eleven color-changing shows. All fixed colors and shows can be modified or changed.

The factory set colors and shows are listed in the Program Table on the next page and can

also be found on the color laminated card included with the light. A color chart can be found

on the same card and will help when programming colors for the ColorLogic lights.

Overview

Page 2

Program Table

Page 3

Network Module Installation

Holding the modem at an angle,

insert the top of the modem into

the cutout.

Step A

Insert the bottom of the modem in place and rotate

the modem until it seats into the cutout.

Step B

Page 4

Remove the plastic plate by sliding it

towards the front of the enclosure.

Step C

The ColorLogic Network Module uses 120VAC power line communications to individually

control each networked light. The same bus must be used to power both the Network

Module and any networked light(s).

Network Module Wiring

NOTE: When using more than one circuit breaker to power Generation 4 ColorLogic

Lights, be sure that the breakers AND the Network Module feed are on the same

phase of power. Page 5

Network Module Wiring

Connect neutral wire (white) from module to neutral bus bar of controller.

Connect load power wire (black) from breaker to module.

Step E

Step D

Connect data cable from module to any open Comm connector on PCB.

Step F

Page 6

ColorLogic Lights Wiring

Connect the pig-tail

wire of the GFCI

breaker to the

neutral bus bar.

Step G

Connect the line power wire

(from breaker) and load power

wire (to lights) to the Lights

Relay.

Step H

To light(s)

Connect the load neutral wire

(from light) to the GFCI breaker.

Step I

From light(s) Page 7

Configuring Lights

Note: Once the ColorLogic configuration process begins,

there is no way to exit and the process must be completed.

During ColorLogic configuration, the Pro Logic will find all networked lights in the

system and assign an identification number to each using the prefix "LT".

Press the + button to activate

ColorLogic options

Step J Press the + button to find ColorLogic

lights

Step K

Page 8

Andere Handbücher für ColorLogic® 4.0

Inhaltsverzeichnis

Andere Hayward Unterwasserbeleuchtung Handbücher

Hayward

Hayward SP0512 Series Bedienungsanleitung

Hayward

Hayward UCL Niches Bedienungsanleitung

Hayward

Hayward ColorLogic SP0536AF Bedienungsanleitung

Hayward

Hayward Proseries SP9120 Bedienungsanleitung

Hayward

Hayward 7016849 Bedienungsanleitung

Hayward

Hayward Universal ColorLogic Bedienungsanleitung

Hayward

Hayward UCL Niches Bedienungsanleitung

Hayward

Hayward Universal ColorLogic Bedienungsanleitung

Beliebte Unterwasserbeleuchtung Handbücher anderer Marken

Keldan

Keldan VIDEO 18X 25000lm CRI82 Bedienungsanleitung

Oase

Oase ProfiLux Garden LED RGB Bedienungsanleitung

Oceanled

Oceanled DISCOVER D3 Bedienungsanleitung

NORBIT

NORBIT AQUA FCL600 Bedienungsanleitung

Keldan

Keldan VIDEO 8XR Ambient 18000lm Bedienungsanleitung

Ikelite

Ikelite PCm - LED Light Bedienungsanleitung

LIGMAN

LIGMAN NEMO 2 Bedienungsanleitung

Oase

Oase Lunaqua 2 Handbuch

Kripsol

Kripsol 061511213000 Bedienungsanleitung

Wibre

Wibre 4.0291 Bedienungsanleitung

Certikin

Certikin PU9CS Bedienungsanleitung

lumishore

lumishore SMX53-SUPRA Bedienungsanleitung

Pyle

Pyle PLEDFN8 Bedienungsanleitung

Filix

Filix Arpool XM Bedienungsanleitung

Aqualuma

Aqualuma Pathway Light Bedienungsanleitung

HEISSNER

HEISSNER U 130-T Bedienungsanleitung

emaux

emaux NP300 Series Bedienungsanleitung

Oceanled

Oceanled XD16 Bedienungsanleitung