HBM Operating Manual Bedienungsanleitung
Quick Start Guide | Kurzanleitung | Guide rapide |
Guía rápida | クイックスタートガイド |
English Deutsch Français Español
QuantumX
Hottinger Baldwin Messtechnik GmbH
Im Tiefen See 45
D-64293 Darmstadt
Tel. +49 6151 803-0
Fax +49 6151 803-9100
www.hbm.com
Mat.: 7-0102.0004
DVS: A02361_05_Z00_01 HBM: public
07.2020
EHottinger Baldwin Messtechnik GmbH.
Subject to modifications.
All product descriptions are for general information only.
They are not to be understood as a guarantee of quality or
durability.
Änderungen vorbehalten.
Alle Angaben beschreiben unsere Produkte in allgemeiner
Form. Sie stellen keine Beschaffenheits- oder Haltbarkeits
garantie dar.
Sous réserve de modifications.
Les caractéristiques indiquées ne décrivent nos produits
que sous une forme générale. Elles n'impliquent aucune
garantie de qualité ou de durabilité.
Reservado el derecho a modificaciones.
Todos los datos describen nuestros productos de manera
general. No representan ninguna garantía de calidad o de
durabilidad.
のはされるがあります。
にのすべてのはのため
のです。やをするも
のではありません。
留变更的权利。
所有息是对我品的般性描。在性能或者耐性方
它并提证。
Quick Start Guide | Kurzanleitung | Guide rapide |
Guía rápida | クイックスタートガイド |
English Deutsch Français Español
QuantumX
2A02361_05_Z00_01 HBM: public QuantumX
English
1 Safety instructions 3........................................
2 Electro magnetic conformity 9...............................
3 Markings used 11............................................
3.1 The markings used in this document 11..........................
3.2 Symbols on the device 12......................................
4 Introduction 13..............................................
4.1 About the QuantumX documentation 13.........................
4.2 The QuantumX family 14......................................
4.3 Module overview/transducer technologies 18.....................
5 Software 19.................................................
6 Connecting individual QuantumX modules 20.................
6.1 Connecting the supply voltage 20...............................
6.2 Connection to a PC 20........................................
6.3 Anschluss an Datenrekorder und Module mit Gateway-Funktion 21..
6.4 Other connection options 23....................................
Safety instructions
QuantumX A02361_05_Z00_01 HBM: public 3
1 Safety instructions
Notice
The safety instructions described here also apply to the power pack NTX001
and the active backplane BPX001, BPX002 and BPX003.
Appropriate use
A module with connected transducers is to be used exclusively for
measurement tasks and Test tasks. Use for any purpose other than the above
is deemed to be non-designated, inappropriate use.
In the interests of safety, the module should only be operated as described in
the Operating Manuals. It is also essential to comply with the legal and safety
requirements for the application concerned during use. The same applies to
the use of accessories.
Before commissioning the module for the first time, you must first run a project
planning and risk analysis that takes into account all the safety aspects of
automation technology. This particularly concerns personal and machine
protection.
Additional safety precautions must be taken in plants where malfunctions could
cause major damage, loss of data or even personal injury. In the event of a
fault, these precautions establish safe operating conditions.
This can be done, for example, by mechanical interlocking, error signaling, limit
value switches, etc.
Notice
The module must not be connected directly to a power supply system. The
supply voltage must be 10 V … 30 V (DC).
Safety instructions
4A02361_05_Z00_01 HBM: public QuantumX
General dangers of failing to follow the safety instructions
Every module is a state of the art device and as such is failsafe. The module
may give rise to residual dangers if it is inappropriately installed and operated
by untrained personnel. Any person instructed to carry out installation,
commissioning, maintenance or repair of the modules must have read and
understood the Operating Manuals and in particular the technical safety
instructions.
The scope of supply and performance of the modules only covers a small area
of measurement technology. In addition, equipment planners, installers and
operators should plan, implement and respond to the safety engineering
considerations of measurement technology in such a way as to minimize
residual dangers. On-site regulations must be complied with at all times. There
must be reference to the residual dangers connected with measurement
technology. After making settings and carrying out activities that are
password-protected, you must make sure that any controls that may be
connected remain in safe condition until the switching performance of the
module has been tested.
Conditions on site
For modules in the housing with degree of protection IP20:
SProtect the modules from dirt and moisture or the effects of weather such
as rain, snow, etc.
SThe permissible relative humidity at 31 oC is 80% (non-condensing); linear
reduction to 50% at 40 oC.
SMake sure that the side ventilation openings are not covered.
For all modules:
SDo not expose the modules to direct sunlight.
SPlease observe the permissible maximum ambient temperatures stated in
the specifications.
SEnsure there is adequate ventilation for installation in the BPX001 back
plane.
Safety instructions
QuantumX A02361_05_Z00_01 HBM: public 5
Maintenance and cleaning
The modules are maintenance-free. Please note the following points when
cleaning the housing:
SBefore cleaning, disconnect all connections.
SClean the housing with a soft, slightly damp (not wet!) cloth. Never use
solvent as this could damage the labeling or the housing.
SWhen cleaning, ensure that no liquid gets into the module or connections.
Outputs
If using outputs such as analog voltage, digital 5/24 V alarms or protocol sig
nals via CAN FD, EtherCAT, PROFINET or others of a module, particular at
tention must be paid to safety. Make sure that status or control signals cannot
initiate any actions that may pose a danger to persons or the environment.
Product liability
In the following cases, the protection provided for the device may be adversely
affected. Liability for device functionality then passes to the operator:
SThe device is not used in accordance with the operating manual.
SThe device is used outside the field of application described in this section.
SThe operator makes unauthorized changes to the device.
Warning signs and danger symbols
Important instructions for your safety are specifically identified. It is essential to
follow these instructions in order to prevent accidents and damage to property.
Safety instructions are structured as follows:
WARNING
Type of danger
Consequences of non-compliance
Averting the danger
Safety instructions
6A02361_05_Z00_01 HBM: public QuantumX
SWarning sign: draws attention to the danger
SSignal word: indicates the severity of the danger (see table below)
SType of danger: identifies the type or source of the danger
SConsequences:describes the consequences of non-compliance
SDefense: indicates how the danger can be avoided/bypassed.
Danger classes as per ANSI
Warning sign, signal word Meaning
WARNING This marking warns of a potentially dangerous situ
ation in which failure to comply with safety require
ments may result in death or serious physical injury.
CAUTION This marking warns of a potentially dangerous situ
ation in which failure to comply with safety require
ments may result in slight or moderate physical injury.
Note This marking draws your attention to a situation in
which failure to comply with safety requirements may
lead to damage to property.
Working safely
The supply connection, as well as the signal and sensor leads, must be
installed in such a way that electromagnetic interference does not adversely
affect device functionality (HBM recommendation: "Greenline shielding design",
downloadable from the Internet at http://www.hbm.com/Greenline).
Automation equipment and devices must be covered over in such a way that
adequate protection or locking against unintentional actuation is provided (e.g.
access checks, password protection, etc.).
When devices are working in a network, these networks must be designed in
such a way that malfunctions in individual nodes can be detected and shut
down.
Safety precautions must be taken both in terms of hardware and software, so
that a line break or other interruptions to signal transmission, e.g. via the bus
interfaces, do not cause undefined states or loss of data in the automation
device.
Safety instructions
QuantumX A02361_05_Z00_01 HBM: public 7
Error messages should only be acknowledged once the cause of the error is
removed and no further danger exists.
Conversions and modifications
The module must not be modified from the design or safety engineering point
of view except with our express agreement. Any modification shall exclude all
liability on our part for any resultant damage.
In particular, any repair or soldering work on motherboards (exchanging
components) is prohibited. When exchanging complete modules, use only
original parts from HBM.
The module is delivered from the factory with a fixed hardware and software
configuration. Changes can only be made within the possibilities documented
in the manuals.
Qualified personnel
Important
This device is only to be installed and used by qualified personnel strictly in
accordance with the specifications and with the safety rules and regulations
which follow.
Qualified persons means persons entrusted with the installation, fitting,
commissioning and operation of the product who possess the appropriate
qualifications for their function. This module is only to be installed and used by
qualified personnel, strictly in accordance with the specifications and the safety
rules and regulations.
This includes people who meet at least one of the three following requirements:
SKnowledge of the safety concepts of automation technology is a require
ment and as project personnel, you must be familiar with these concepts.
SAs automation plant operating personnel, you have been instructed how to
handle the machinery and are familiar with the operation of the modules and
technologies described in this documentation.
Safety instructions
8A02361_05_Z00_01 HBM: public QuantumX
SAs commissioning engineers or service engineers, you have successfully
completed the training to qualify you to repair the automation systems. You
are also authorized to activate, ground and label circuits and equipment in
accordance with safety engineering standards.
It is also essential to comply with the legal and safety requirements for the
application concerned during use. The same applies to the use of accessories.
Inhaltsverzeichnis
Sprachen:
Andere HBM Datenlogger Handbücher
HBM
HBM QuantumX Bedienungsanleitung
HBM
HBM eDAQXR-lite Bedienungsanleitung
HBM
HBM QuantumX Bedienungsanleitung
HBM
HBM QuantumX CX22-W Bedienungsanleitung
HBM
HBM SomatXR MX Series Bedienungsanleitung
HBM
HBM espressoDAQ DQ401 Bedienungsanleitung
HBM
HBM PMX Bedienungsanleitung
HBM
HBM QuantumX Bedienungsanleitung
HBM
HBM QuantumX CX22 Bedienungsanleitung
HBM
HBM SomatXR CX23-R Bedienungsanleitung
