Headsight TS-JD9x10 Bedienungsanleitung
TS-JD9x10
Manual 09050102b
i
About TrueSight
Contacting Headsight
Headsight, Inc
3529 Fir Rd
Bremen, IN 46506
Phone:574-546-5022
Fax: 574-546-5760
Web: www.headsight.com
About this Manual
How to use this manual
The numbered sections are instructions which should be completed for each
system. The lettered appendices are information which may be of interest, but is
not required for ordinary use.
This icon designates information of which you should take note.
This icon designates an important instruction.
Disclaimers
Headsight and TrueSight are trademarks of Headsight, Inc.
John Deere, JD, CaseIH, AFX, CAT, LEXION, AGCO, New Holland, Trimble,
Outback, WeatherPack, MetriPak, AutoTrac, AccuGuide, EZ-Steer, OnTrac,
AutoTrac, AutoPilot and all other trademarks are property of their respective
owners.
Suggestions
If you have any suggestions to improve this manual –please call 574-546-5022 or
ii
Table of Contents
About TrueSight i
Contacting Headsight i
About this Manual i
How to use this manual i
Disclaimers i
Suggestions i
1Quick-Start Guide 1
1.1Identify the components 1
1.2Install the system 5
1.3Learn how to use TrueSight 5
1.4Perform the initial calibration steps 5
1.5Complete in-field tuning 8
2Installation 9
2.1Harness installation 9
2.1.1Wiring overview 9
2.1.2Access panel 11
2.1.3Feeder clutch 11
2.1.4Power supply 12
2.1.5Auxiliary switch 12
2.1.6Remote controller 13
2.1.7Base controller 13
2.1.8Safety connectors 14
2.1.9Optional: Feeder position sensor 14
2.1.10Crop sensor 14
2.1.11Speed sensor 14
2.1.12Wheel angle sensor wiring 15
2.2Wheel angle sensor installation 15
2.3Steering device wiring 17
2.3.1Trimble AutoPilot 17
2.3.2OnTrac motor 18
2.3.3EZ-Steer motor 18
2.3.4Outback valve 19
2.4Crop sensor installation 20
2.4.1Sensor assembly 20
iii
2.4.2Width adjustment 21
2.4.3Safety reminder 21
2.4.4Snout choice 21
2.4.5Sensor mounting 22
2.4.6Wiring instructions 23
3Operation 24
3.1Controls description 24
3.2Run screen controls 25
3.3Menu controls 25
4Settings 26
4.1Range (Default = 40) 26
4.2Tilt range (Default = 20) 26
4.3Auxiliary engage 27
4.4Alert timer 27
4.5LCD backlight (Default = 10) 27
4.6LCD contrast (Default = 10) 27
4.7Gain (Default = 6) 27
4.8Deadband (Default = 8) 27
4.9Auto-engage delay (Default = 2.5 sec) 28
4.10Override value (Default = 6) 28
4.11Speed select (Default = GPS) 28
4.12Speed value (Default = 10,700) 28
4.13Gain balance (Default = 0) 28
4.14Left Deadzone (Default = Calibrated Value, 0 if not calibrated) 29
4.15Right Deadzone 29
4.16System select 29
4.17Fine Control (Default = 0) 29
4.18Range2 (Default = 20) 29
5Calibration 30
5.1Bump centering calibration 30
5.2Wheel angle sensor calibration 30
5.3Auto-engage sensor calibration 31
iv
5.4Speedometer calibration 31
5.5Tilt calibration 31
5.6Auto Dead Zone 31
AMenu Layout 32
BTroubleshooting 33
1Troubleshooting by TrueSight™ service code 33
Error 1 or 3 – Comm Failed 33
Error 2 – Wheel Angle Not Done 33
Error 11 - Crop Sensor > 4.7V 34
Error 12 - Crop Sensor < 0.3V 35
Error 21 - Wheel Angle Sensor > 4.7V 37
Error 22 - Wheel Angle Sensor < 0.3V 38
Error 23 - Wheel Angle Swing < 1V 40
Error 24 - Wheel Angle Not Found 41
Error 31 - Feederhouse > 4.7V 42
Error 32 - Feederhouse < 0.3V 43
Error 46 or 47 - Speed out of Range 44
Error 54 - Encoder Not Detected 46
Error 66 – Steering Wheel Moving 47
Error 74/78/88 – No 12V or 5V Safety 48
Error 99 – Outputs are Reversed 48
2Troubleshooting by symptom 49
System is engaged, but doesn’t steer 49
When the system is engaged, it steers fully to the right or left 50
3Wiring Information 51
JD9x10 series 51
EZ-Steer & Ontrac 52
Outback 53
Trimble AutoPilot 54
CSoftware Updates 55
1Basic preparation 55
v
2Updating the Base controller 55
3Updating the Remote controller 56
4Finishing up 56
D Sensor Parts 57
1
1Quick-Start Guide
Note: Follow the steps in order in this Quick-Start section when
installing the system for the first time. All of the calibration and tuning steps
will be available in the TrueSight menu.
1.1 Identify the components
1. Remote controller
1- -Remote
1- -Mount kit
2. Base controller
1- -Base
3. Crop sensor assembly
1- HT2501 -Crop sensor asm
For parts breakdown see
appendix.
2
4. Crop whiskers
2- HT2695 -Arm TrueSight
5. Crop sensor mounting kit
oMay vary based on header
1- B2711 -Mounting kit
1- HT2711 -Bracket
2- 08200115 -Bolt M10x50
2- 08200134 -Bolt 5/16” x .75”
2- 08200133 -Washer 5/16”
AR- 08100101 -Cable clamp small
AR- 08100102 -Cable clamp large
AR- 08300102 -Zip ties
6. Main harness
oMay vary based on system
type
1- TS-JD010-TREZ-harness
7. Wheel angle sensor asm
1- HT2503 -Wheel sensor asm
For parts breakdown
see appendix.
3
8. Feedback sensor hardware kit
1- BTSF1 -hardware kit
1- HT2693 -tie rod asm
1- HT2784 -bracket tie rod clip
2- 08100111 -3” hose clamp
2- 08200181 -Bolt 5/16” x 2.25”
2- 08200151 -Nut flange 5/16
1- 08100137 -Clip
9. Feedback sensor bracket kit
1- B2712 -bracket kit
1- 08200176 -bolt 3/4” x 7”
1- 08200165 -nylon lock nut 3/4
10. Wheel angle sensor wiring
extension
1- PFB23 -23’ wiring extension
4
11. Footswitch
AR- HT2810 -footswitch
12. Footswitch adapter
AR- HT2806 -footswitch adapter
When applicable
13. Harness attaching hardware
1- BTS1 -hardware kit
1- 08300109 -3/16 allen wrench
1- 08300108 -5/32 allen wrench
AR- 08100101 -Cable clamp small
AR- 08300102 -Zip ties
14. GPS
1- HT-GPS -GPS unit
1- HT2735 -GPS mount
Inhaltsverzeichnis
Andere Headsight Controller Handbücher
