3
15. Insertthe leg ofthe top pivotbracket up intothe hole in
thedoortrack. Line up thetoppivot bracket with holein
the corner brace on top of the door and attach with the
slottedhinge screw andsteel washer (bothdoors).
16. Align doors by readjusting the pivot brackets and steel
washers and sliding the doors in or out.
17. Insert the ball stud into the hole in the ball stud plate.
Slide into the door as shown in Figure 6.
OPERATING PRECAUTIONS AND
INSTRUCTIONS
Theglassdoorsandthefireplacefluedampermustbothbe
inthe fully openposition before startingyour fire.
Follow the procedure for building and starting a fire as de-
tailedinyourfireplace homeowners manual. Youmayclose
the doorsAFTER the fire is well started.THE FIRST FEW
FIRESMUSTBE SMALLTOALLOWTHEPROPERTEM-
PERING OF THE GLASS AND TO PREVENT GLASS
BREAKAGE.
Donot,however, close the doors on anexcessivelyhotfire.
The glass must be allowed to warm slowly. Keep the fire
well back from the doors and never let flames contact the
glass.
Ifthe fire gets toolarge at anytime,open both setsofglass
doors.Thiswill quickly reduce the heatinthefirebox. Push
the logs or other fuel to the center of the firebox and rear-
range into single layer. Let the fire burn to a smaller size
beforeclosing the glassdoors again.
WARNING: FIREPLACES EQUIPPED WITH DOORS
SHOULD BE OPERATED ONLY WITH DOORS FULLY
OPENOR DOORSFULLYCLOSED. IF DOORSARELEFT
PARTLYOPEN,GASANDFLAMEMAYBEDRAWN OUT
OF THE FIREPLACE OPENING, CREATING RISKS OF
BOTHFIREANDSMOKE. MAKESURETHEFIREPLACE
SCREENISCLOSEDWHENTHEDOORSAREOPEN.
Thefollowingchecklistsummarizesthekeystepsdiscussed
underOPERATINGINSTRUCTIONS:
1. Opendoorsandfireplacedamper.
2. Buildfire as describedinfireplace manual.
3. Close doors after the fire is started IF fire is normal
size.
4. Iffiregetstoolarge,opendoorsandreducesizeoffire.
5. Keep damper open until fire is completely out and all
smoking has stopped.
Formaximumbenefitandefficientusage,referto operating
instructionsin owner's manual.
Figure 6
18. Attachtheballstudreceiverbracketstothebottomdoor
track. Use the 4 1/4" screws as shown in Figure 7.
Figure 7
19. Line up the ball studs and receiver brackets by sliding
the receiver brackets up and down, and the ball studs
leftand right. Once thesepartsare aligned, tightenthe
screws on the receiver brackets and turn the ball stud
1/4turnpasthandtight. DONOTOVERTIGHTENTHE
BALLSTUD.
20. If the ball studs and receiver brackets are not holding
the doors closed, you may need to compress the gas-
ketmaterialonthebackof the door by pressingitdown
withyourfingers.
NOTE:The ball studmayneed to be adjustedafterthe first
couple of fires. Periodically check the alignment of the ball
studwith the ball studreceiver bracket andadjustif neces-
sary.
BALL STUD
BALL STUD
PLATE
BALL STUD
RECEIVER BRACKETS
REPLACEMENT PARTS KITS
GD415ATBPB GD485ATPB
Side Filler 690-105 690-105
Front Filler 690-106 691-106
Top/Bottom Tracks 690-108 691-108
Left Door 690-390A 691-390A
Right Door 690-391A 691-391A
Hardware Kit Includes:
Hinge: Bottom Left & Right
Hinge: Top Left & Right
Ball Stude & Plate
Ball Stud Receiver Bracket
Handles & 3/4" Screws for Handles
Slotted Hinge Screws
Washers
1/2" Sheetmetal Screws
1/4" Screws for Ball Stud
Receiver Bracket
690-100A 690-100A
REPLACEMENT PARTS
