Heat & Glo 6000TRSI-AUC Bedienungsanleitung

Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

MODEL: 6000TRSI-AUC

AUSTRALIAN GAS ASSOCIATION CERTIFIED

CERTIFICATE NUMBER 5668

THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED

BY HOMEOWNER FOR OPERATION AND MAINTENANCE.

HEAT & GLO, a brand of Hearth & Home Technologies Inc.

20802 Kensington Boulevard, Lakeville, MN 55044, USA, www.heatnglo.com

INSTALLATION AND OPERATION INSTRUCTIONS

THIS PRODUCT MAYBE COVERED BY ONE OR MORE OF THE FOLLOWING PATENTS:

(UnitedStates)4593510,4686807,4766876,4793322,4811534,5000162,5016609,5076254,5113843,5191877,5218953,5263471,5328356,5341794,5347983,5429495,5452708,5542407,

5601073,5613487,5647340, 5688568,5762062,5775408, 5890485,5931661,5941237, 5947112,5996575, 6006743,6019099,6048195, 6053165,6145502, 6170481, 6237588,6296474,

6374822,6413079,6439226,6484712,6543698,6550687,6601579,6672860,6688302B2,6715724B2,6729551,6736133,6748940,6748942,D320652,D445174,D462436;(Canada)1297749,

2195264,2225408; (Australia) 543790;586383; (Mexico) 97-0457; (New Zealand)200265; orother U.S. and foreign patents pending.

2Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

IMPORTANT: Read all instructions carefully before starting installation.

Failuretofollowtheseinstallation instructions mayresult in apossible fire

hazardand will voidthe warranty.Save thismanual for futurereference.

MODEL6000TRSI-AUC

ISAUSTRALIAN GASASSOCIATION

APPROVED FOR NATURALGAS OR PROPANE

ASABALANCED FLUE HEATER.

Referto theappliance dataplates forgas consump-

tionsand pressures.

Installation of this appliance should only be carried

outby an authorized personin accordance withthe

manufacturers instructions.All relevant codes and

regulations laid down by the gas fitting authorities,

municipalbuildingregulations,electrical wiringregu-

lations, and the requirements of the AGA Gas In-

stallationCode must beobserved.

This appliance and its components are tested and

safewhen installed inaccordance with this Installa-

tion Manual. Report to your dealer any parts dam-

aged in shipment, specifically check glass condi-

tion.The gas logs andflue system componentsare

in separate packages. Read all instructions before

PLEASE READ THIS MANUAL BEFORE INSTALLING AND

USING THIS APPLIANCE.

starting installation and follow these instructions

carefullyduringinstallationtoensuremaximum ben-

efit and safety. Failure to follow them will void your

warrantyand may present a fire hazard.

TheHeat& Glowarrantywill bevoidedby,andHeat

& Glo disclaims any responsibility for the following

actions:

• Installationof anydamaged heater orflue sys-

temcomponent

• Modificationof the heateror balancedflue sys-

teminstallationotherthan as instructedbyHeat

& Glo.

• Improperpositioningofthegaslogsortheglass

door

• Installation and/or use of any component part

not manufactured or approved by Heat & Glo,

not withstandinganyindependenttesting labo-

ratory or other party approval of such compo-

nent part or accessory.

Heat & Glo, a brand of Hearth & Home Technologies, Inc.

20802 Kensington Blvd., Lakeville, MN 55044, USA

Heat & Glo Quality Systems

registered by SGS ICS

Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

TABLE OF CONTENTS

1.0 INSTALLATION INSTRUCTIONS. ................................................................... 4

A. Locating theHeater ..................................................................................... 5

B. FramingtheHeater ..................................................................................... 6

C. FlueSystemApprovalsand Installations ...................................................... 8

D. Connectingthe GasSupply ......................................................................... 18

E. Ignition System Wiring ................................................................................. 19

F. MantelClearances ...................................................................................... 21

G. LogPlacement............................................................................................ 22

H. InstallerTesting ............................................................................................ 24

2.0 OPERATING INSTRUCTIONS. ........................................................................ 24

A. Safetyand LightingInformation.................................................................... 26

B. PowerOutage ............................................................................................. 27

C. FanOperation ............................................................................................. 27

3.0 SERVICING AND MAINTENANCE. ................................................................. 28

A. Removalof CoversforServicing ................................................................. 29

B. RemovalofComponentsforService ........................................................... 29

C. PartsReplacement...................................................................................... 29

D. Adjustmentsand ReplacementParts ........................................................... 29

E. Troubleshooting........................................................................................... 30

4.0 REPLACEMENT PARTS. ................................................................................ 33

LimitedWarranty ............................................................................................... 35

4Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

FIGURE1.1 Diagram of the 6000 Series

1.0 INSTALLATION INSTRUCTIONS

When planning a heater installation, it’s necessary

todetermine:

•Where the unit is to be installed.

•The flue system configuration to be used.

•Gas supply piping.

•Electricalwiring.

•Framingand finishing details.

Ifthe heater isto be installedon carpeting ortile, or on

anycombustible materialother thanwood flooring,the

heater should be installed on a metal or wood panel

that extends the full width and depth of the heater.

2-1/2

[]

126.9

[]

686

[]

6-7/8

174

[]

2-3/8

[]

Ø8203[]

9-7/8

250[]

28-3/8 722[]

14-1/4 362

[]

21-1/2

547[]

18-3/4

476[]

31-5/8

803[]

41 1043[]

36-1/8

917[]

965[]

ELECTRICAL

ACCESS

GAS LINE

ACCESS

TOP

STANDOFFS

GLASS

DOOR

DATA BADGE & LABELS

ELECTRICAL

ACCESS

GAS CONTROLS

AND SWITCHES

GAS LINE

ACCESS

(BEHINDACCESSDOOR)

Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

Clearance Requirements

The top, back, and sides of the heater are defined by standoffs.

The minimum clearance to a perpendicular wall extending past the face of the heater is

one inch (25 mm).

For6000 SeriesModels, the backof theheater may be recessed 21-1/2inches (546mm)

into combustible construction.

FIGURE 1.2 Heater Dimensions, Locations and Space Requirements

A. Locating the Heater

Thediagram (seeFigure 1.2) showsspace andclearance requirements for locating aheater withina room.

Minimum Clearances from the Heater to

Combustible Materials

Glass Back of Sides of Top of

Front Floor Heater Heater Heater Ceiling

36 inches 0 1/2inch 1/2inch 3-1/2inches 31 inches

(914mm) (13mm) (13mm) (89 mm) (787mm)

1”MIN. (25mm)

3” (76.2mm)

A B C D E

Inches 42 22 38 53-3/4 76

Millimeters 1066 559 965 1365 1930

Rear Flue

A B C D E

Inches 42 22 36 50-15/16 72

Millimeters 1066 559 914 1294 1829

1” MIN. (25mm)

1/2” MIN. (12.5mm)

Top Flue

For minimum clearances, see the direct flue termination clearance diagrams on page 7.

Minimum Clearances from the Flue Pipe to Combustible Materials

For Horizontal Sections For Vertical

Sections At Wall Firestops

Top Bottom Sides 1 inch

(25mm)

Top Bottom Sides

3 inches

(75mm) 1 inch

(25mm) 1 inch

(25mm) 2-1/2 inches

(63.7mm) 1/2 inch

(13mm) 1 inch

(25mm)

6Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

Framing should be constructed of

2 X 4 lumber or heavier.

ABC DE

42-1/8 in. 38-19/32 in. 22-1/16 in. 26-7/8 in. 47-3/4 in.

(1070mm) (980mm) (560mm) (684mm) (1060mm)

FIGURE1.3 Framing Dimensions

B. Framing the Heater

Framingcan be built before orafter the heater is setin

place. Framing should be positioned to accommodate

wallcoverings andheater facingmaterial. The diagram

belowshows framingreference dimensions.

The framing

headers may rest

on the heater

standoffs.

CAUTION: MEASURE HEATER DIMENSIONSAND

VERIFY FRAMING METHODS AND WALL COVER-

INGDETAILS,BEFORE FRAMING CONSTRUCTION

BEGINS.

* NOTE: Dimension Btaken from finished

hearthframe. DimensionsDand Etaken

frombottom of unit.

86 mm

76 mm

NON-COMBUSTIBLE ZONE

IS DEFINED BY 76MM ABOVE

THE ELBOW FOR THE ENTIRE

WIDTH AND DEPTH (BEHIND

THE FRONT HEADER) OF

THE FIREBOX.

WALL

STUD

Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

NOTES: 1. All distances are measured vertically or horizontally along the wall to a point

in line with the nearest part of the terminal.

2. Prohibited area below electricity meter or fuse box extends to ground level.

3. See clause 5.13.6.6 for restrictions on a flue terminal under a roofed area.

4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a flue

terminal to a LP Gas cylinder. A flue terminal is considered to be a source of ignition.

MINIMUMCLEARANCESREQUIREDFORBALANCED FLUE TERMINALS

ORTHEFLUETERMINALS OF OUTDOORAPPLIANCES

FIGURE1.4

CLEARANCES 'n' (mm)

Space heaters All other appliances

Up to 50 MJ/h

input UP to 50 MJ/h

input Over 50 MJ/h &

to 150 MJ/h

Over 150 MJ/h

input

150 500 1000 1500

a - Below eaves, balconies or other projections: MIN. CLEARANCE (mm)

Appliances up to 50 MJ/h input ........................................................................................... 300

Appliances over 50 MJ/h input ............................................................................................ 500

b - From the ground or above a balcony...................................................................................... 300

c - From a return wall or external corner ..................................................................................... 500

d - From a gas meter (M) ...........................................................................................................1000

e - From an electricity meter or fuse box (P) ............................................................................... 500

f - From a drain or soil pipe......................................................................................................... 150

g - Horizontally from any building structure (unless appliance approved

for closer installation) or obstruction facing a terminal ......................................................... 500

h - From any other flue terminal, cowl, or combustion air intake ............................................... 500

j - Horizontally from an openable window, door, non-mechanical air

inlet, or any other opening into a building, with the exception of

sub-floor ventilation:

Appliances up to 150 MJ/h input ......................................................................................... 500

Appliances over 150 MJ/h input ........................................................................................1500

k - From a mechanical air inlet, including a spa blower .........................................................1500

n - Vertically below an openable window, non-mechanical air

inlet or any other opening into a building, with the exception of ................................. See table

sub-floor ventilation............................................................................................................. below

T = Flue terminal M = Gas meter Shading indicates prohibited

I = Mechanical air inlet P = Electricity meter or fuse box areas for flue terminals

8Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

This model is approved to use DVP-Series flue pipe

components.ADVP-TRAP2TerminationCapmustbe

usedtoterminatefluesystemsinahorizontalposition.

ADVP-TVHWverticalTerminationCapmustbeusedto

terminate flue systems in a vertical position.

Figures 1.7 through 1.14 show the flue systems ap-

provedforthese models.Approvedflue systemcompo-

nents are labeled for identification. NO OTHER FLUE

SYSTEMS OR COMPONENTS MAY BE USED. De-

tailed installation instructions are included with each

flue termination kit and should be used in conjunction

with this manual.

WARNING: THIS GAS APPLIANCE AND FLUE AS-

SEMBLY MUST BE FLUED DIRECTLY TO THE OUT-

SIDEAND MUSTNEVER BEATTACHEDTOACHIM-

NEYSERVINGASEPARATE SOLIDFUELBURNING

APPLIANCE. EACHGAS APPLIANCE MUSTUSE A

SEPARATE FLUE SYSTEM-COMMON FLUE SYS-

TEMSARE PROHIBITED.

CAUTION: UNDER NO CONDITION SHOULD COM-

BUSTIBLEMATERIALBECLOSER THAN 3 INCHES

(2 1/2 INCHES AT WALL FIRESTOPS) FROM THE

TOPOFTHE8 INCH PIPE OR 1- INCH TO THESIDES

AND THE BOTTOM FOR HORIZONTAL SECTIONS

OF THIS FLUE SYSTEM. VERTICAL SECTIONS OF

THIS SYSTEM REQUIRE A MINIMUM OF 1 INCH

CLEARANCE TO COMBUSTIBLE MATERIALS ALL

AROUND THE 8 INCH PIPE.

For alternative installations, other than depicted, con-

tactyour dealer forfurther information.

Refer to Figure 1.4 for required clearances to flue ter-

minals.

MODEL FLUE TERMINATIONAPPROVALS

6000TRSI-AUC DVP-TRAP2, DVP-TVHW

TABLE 1

FIGURE1.5

VERTICALFLUERESTRICTOR

Ifthe heater installationrequires avertical flueexceed-

ing 4.5m above the unit with no horizontal flue or el-

bows a vertical flue restrictor must be installed (see

Figure1.5).

FIGURE1.6

CAP

MAX.RUN

36FT.

(10.97m)

STRAIGHT UP VERTICAL FLUE SYSTEM

Figure 1.6 shows straight up vertical flue system ap-

provedfor use on thismodel.

C. FLUE SYSTEM APPROVALS AND

INSTALLATIONS

RESTRICTOR

PLATE

Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

FIGURE 1.7 Straight Out Horizontal Flueing

MIN.RUN MAX. RUN

13.1"(331mm) 24" (610mm)

FIGURE1.8 Flueing with One 90° Elbow

V H

1´ MIN. (0.30 M) 2´ MAX. (0.61 M)

2´ MIN. (0.61 M) 4´ MAX. (1.22 M)

3´ MIN. (0.91 M) 6´ MAX. (1.83 M)

4´ MIN. (1.22 M) 8´ MAX. (2.44 M)

24´ MAX. (7.32 M) 8´ MAX. (2.44 M)

STRAIGHT OUT HORIZONTALFLUE SYSTEM

Figure 1.7 shows straight out horizontal flue systems

approvedfor use onthis model.

ONE(1)90-DEGREEELBOW

Figures 1.8 and 1.9 show an installation using one (1)

90-degree elbow. Dimension V is listed as MINIMUM

verticaldimensions and dimensionH is listed as corre-

sponding MAXIMUM horizontaldimensions.

TWO(2)90-DEGREEELBOWS

Figures 1.10 and 1.11 show examples of possible in-

stallationsusing two (2) 90-degree elbows. Dimension

V is listed as MINIMUM vertical dimensions, dimen-

sion H is listed as MAXIMUM beginning horizontal di-

mensions,anddimension H+H1islisted ascorrespond-

ing TOTALMAXIMUM horizontaldimensions.

THREE(3)90-DEGREEELBOWS

Figures 1.12 through 1.14 show examples of possible

installationsusing three (3) 90-degree elbows. Dimen-

sions V are listed MINIMUM first vertical dimensions

and dimensions H are listed as beginning MAXIMUM

horizontaldimensions. DimensionsH+H1 andH+H1+H2

arelisted asTOTAL MAXIMUM horizontaldimensions.

DimensionsV+V1are listed asTOTALMAXIMUM ver-

tical dimensions.

ELBOWS

The flue systems installed on this gas heater may

also include one (1), two (2), or three (3) 90 - degree

elbowassemblies.

Figures 1.8 through 1.14 and their corresponding

tables show examples of flue configurations using

elbows. The relationships of vertical rise to horizon-

tal run in flue configurations using elbows MUST be

strictly adhered to.

10 Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

FIGURE 1.10 Flueing with Two 90° Elbows

V FT.) H (FT.) H+H1 (FT.)

1' MIN. (0.30 M) 2' MAX. (0.61 M) 4' MAX. (1.22 M)

2' MIN. (0.61 M) 2' MAX. (0.61 M) 8' MAX. (2.44 M)

3' MIN. (0.91 M) 4' MAX.(1.22 M) 12'MAX. (3.66 M)

4' MIN. (1.22 M) 6' MAX. (1.83 M) 16'MAX. (4.88M)

20' MAX. (6.10M) 6' MAX. (1.83 M) 16'MAX. (4.88M)

V (FT.) H (FT.)

1' MIN. (0.30 M) 4' MAX. (1.22 M)

2' MIN. (0.61 M) 8' MAX. (2.44 M)

3' MIN. (0.91 M) 12' MAX. (3.66 M)

4' MIN. (1.22 M) 16' MAX. (4.88 M)

V+H= 24’ MAX. (7.32 M)

FIGURE1.9 Flueing with One 90° Elbow

NOTE:A6-inch (152mm) sectionof straight pipemust

needto be attachedtothe fireplace beforea 90o elbow.

Andere Handbücher für 6000TRSI-AUC

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo 6000CLX-IFT-S Bedienungsanleitung

Heat & Glo

Heat & Glo SL-350TRS-D Bedienungsanleitung

Heat & Glo

Heat & Glo FB-ZC Bedienungsanleitung

Heat & Glo

Heat & Glo REVO-V12 Bedienungsanleitung

Heat & Glo

Heat & Glo BE-41 Montageanleitung

Heat & Glo

Heat & Glo SL-550TV-D Bedienungsanleitung

Heat & Glo

Heat & Glo Passage Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO48ST Bedienungsanleitung

Heat & Glo

Heat & Glo Heat & Glo RED40 Bedienungsanleitung

Heat & Glo

Heat & Glo ST-550TM-IPI Leitfaden

Heat & Glo

Heat & Glo SOHO-N-CEB Programmierhandbuch

Heat & Glo

Heat & Glo COSMO Bedienungsanleitung

Heat & Glo

Heat & Glo RUTH42-B Bedienungsanleitung

Heat & Glo

Heat & Glo 6000C-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo SL-750TRS-C Montageanleitung

Heat & Glo

Heat & Glo 6000CLX-IPI-T Bedienungsanleitung

Heat & Glo

Heat & Glo 8000TR-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo SOHO24B Bedienungsanleitung

Heat & Glo

Heat & Glo ESCAPE-I35-F Bedienungsanleitung

Heat & Glo

Heat & Glo Pier-HVB-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo Escape-42DV Bedienungsanleitung

Heat & Glo

Heat & Glo EM-415 Bedienungsanleitung

Heat & Glo

Heat & Glo Rutherford-42 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch