Heat & Glo KENWOOD SERIES Bedienungsanleitung

Heat & Glo • Kenwood Corner Surround • 2118-934 • 4/07 1

CAUTION

Sharp Edges

• Wear protective gloves and safety

glasses during installation.

KENWOOD CORNER SURROUND

- Installation Instructions -

• These instructions apply only to the cabinet and facing

material that will surround the ﬁrebox.

• See the ﬁreplace manufacturer’s installation instructions to

ensure that all clearance and installation requirements are

being met.

PREPARATION

Before beginning installation of this mantel, verify that the walls

and ﬂoor in the area of the installation are clean, plumb and

level. Any major deviation should be remedied before installing

the ﬁreplace, marble or the mantel /cabinet.

These questions should also be considered and answered

before beginning installation of the mantel.

a. Is base molding already installed?

b. Where are the electrical outlets or ﬁrebox switch?

c. Is there enough distance between windows and edge

of cabinet?

d. Is the ﬁreplace centered between walls?

e. Where is the return air vent located?

f. Is the ﬁreplace centered between windows?

g. Where are the electrical & cable outlets positioned?

h. What type of ﬁnished ﬂooring is to be installed?

It is recommended that two people assemble this mantel due to

its weight and upright positioning.

CAUTION

WARNING

Risk of Fire

• Improper installation or adjustment can

cause injury or property damage. For

assistance or additional information, contact

a qualiﬁed installer, service agency or the

gas supplier.

• Comply with all minimum clearances to

combustibles as speciﬁed in the ﬁreplace

manual.

CAUTION

Leave this manual with party responsible for

use and operation.

Tools and supplies needed:

#2 Phillips Screwdriver

High Temperature Silicone Caulk

Finishing Nails & Hammer

Level

Figure 1. Kenwood Corner Mantel Shown with Optional Base (Left) or without Base (Right).

Heat & Glo • Kenwood Corner Surround • 2118-934 • 4/072

MANTEL TOP

LEFT LEG

RIGHT LEG

UPPER TRIM

RIGHT TRIM

LEFT TRIM

FACE BOARD

BASE (OPTIONAL)

TOP FINISH SUPPORT

SIDE FINISH

SUPPORT

Parts List and Diagram

MANTEL PARTS:

QTY DESCRIPTION

1 Mantel Top

1 Right Leg

1 Left Leg

1 Face Board

1 Upper Trim

1 Left Trim

1 Right Trim

1 Base (Optional)

2 Side Ledger Board (not shown)

2 Top Ledger Board (not shown)

1 Top Finish Support

2 Side Finish Support

ASSEMBLE MANTEL

1. Remove all components from packaging. Conﬁrm

that all components are included. See Figure 2.

Note: Side and Top ﬁnish material supports may come

pre-assembled to left and right legs and face board. If

they are shipped separately they should be attached

prior to step 2.

2. Position left and right mantel legs laying ﬂat on a

clean ﬂoor.

3. Attach face board to the legs. See Figure 3.

4. Make sure all seams and edges are tight and

square.

5. Carefully lift assembly into upright position.

6. Have someone hold the front and legs from the front,

and set the mantel top into location. Attach the mantel

top. See ﬁgure 4.

Figure 2. Components Overview

Figure 3. Attaching Face Board

Figure 4. Attaching Mantel

Note: Using the optional base will raise the ﬁreplace by

9-1/4 inches above ﬁnished ﬂoor level. All dimensional

requirements of the ﬁreplace installation manual should be

adjusted accordingly. See ﬁreplace installation manual for

more details.

INSTALLATION

1. Position base on the ﬂoor in the desired ﬁreplace

location (optional).

2. Set Fireplace into position.

3. Carefully position mantel in desired location.

Heat & Glo • Kenwood Corner Surround • 2118-934 • 4/07 3

Figure 5. Installed View-Shown prior to installation of

ﬁnishing material

Please contact your Heat & Glo dealer with any

questions or concerns.

For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

Heat & Glo, a brand of Hearth & Home Technologies Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

www.heatnglo.com

4. Adjust ﬁreplace position to align properly with mantel.

5. Mark ﬁnal location of ﬁreplace.

6. Using a sharp pencil, draw lines across the back

edges of the mantel and also on the outside edges

of the vertical legs.

7. Carefully remove the mantel and ﬁreplace from the

base.

8. Measure 3/4 in.down from the top lines, and 3/4 in.

in from the side lines. Mark 2 points off of each line,

and draw corresponding line. These lines will be

used to locate the top and side ledger boards.

9. Using a stud ﬁnder or other method, mark off the lo-

cations of the vertical studs that intersect with the top

edges of the mantel. Attach the top and side ledger

boards using 3” drywall screws.

10. Install ﬁreplace according to instructions in ﬁreplace

installation manual.

Risk of Fire

• When being installed in a corner cabinet, SL-

TRS models (SL-350TRS, SL-550TRS, SL-

750TRS) MUST be rear vented using one 90°

elbow off the rear of the unit and an additional

90° elbow to vent out through the wall. See

ﬁreplace installation manual for more details.

• Failure to vent appropriately may cause

excessive heat and/or ﬁre.

WARNING

11. Place the mantel in the corner with the top resting

on the ledger board. Pre-drill holes down through

the top of the mantel into the ledger board. Pre-drill

holes through the legs of the mantel into the side led-

ger boards. Attach the mantel to the ledger boards

using nails through the pre-drilled holes. Caulk sides

of mantel if needed with silicone caulk.

12. Install non-combustible facing material with a maxi-

mum thickness of 1 inch.

13. To install trim strips, place the top, left and right trim

strips in position. Cut trim strips to length. Pre-drill

holes in trim strips and attach them to mantel using

nails. Be careful not to hit the facing material when

nailing the trim strips in place.

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo SL-550METRO-BU Bedienungsanleitung

Heat & Glo

Heat & Glo SL-350TRS-CE-D Montageanleitung

Heat & Glo

Heat & Glo R-4INS Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO-II-48 Bedienungsanleitung

Heat & Glo

Heat & Glo AT-ZC Montageanleitung

Heat & Glo

Heat & Glo Cosmo SLR Bedienungsanleitung

Heat & Glo

Heat & Glo 6TRSI-AUD Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO-II-48 Bedienungsanleitung

Heat & Glo

Heat & Glo FB-GRAND Bedienungsanleitung

Heat & Glo

Heat & Glo MONTANA-42C Bedienungsanleitung

Heat & Glo

Heat & Glo VRTIKL Bedienungsanleitung

Heat & Glo

Heat & Glo 6000TRI-IPI Montageanleitung

Heat & Glo

Heat & Glo GATEWAY Montageanleitung

Heat & Glo

Heat & Glo SL-350TRS-D Bedienungsanleitung

Heat & Glo

Heat & Glo TRUE-36C Bedienungsanleitung

Heat & Glo

Heat & Glo ST-36TRB-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo XLR-PB-CE Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-50 Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo COSMO-I30 Bedienungsanleitung

Heat & Glo

Heat & Glo TRUE-36C Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CL-IPI-S Bedienungsanleitung

Heat & Glo

Heat & Glo Heat & Glo RED40 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch