Heat & Glo SL-350TRS-CE-D Montageanleitung

- Do not store or use petrol or other flam-

mable vapors and liquids in the vicinity of

this or any other appliance.

-What to do if you smell gas

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from

a neighbor's phone. Follow the gas

supplier’s instructions

• If you cannot reach your gas supplier,

call the fire department.

- Installation and service must be performed

by a qualified installer or competent

person.

Model:

SL-350TRS-CE-D Installers Guide

WARNING: IMPROPER INSTALLATION,

ADJUSTMENT, ALTERATION, SERVICE

OR MAINTENANCE CAN CAUSE INJURY

OR PROPERTY DAMAGE. REFER TO

THIS MANUAL. FOR ASSISTANCE OR

ADDITIONAL INFORMATION CONSULT A

QUALIFIED INSTALLER OR

COMPETENT PERSON.

2033-900G 7/04

READ THIS MANUAL BEFORE INSTALLING OR

OPERATING THISAPPLIANCE. THIS INSTALLERS

GUIDE MUST BE LEFT WITH APPLIANCE FOR

FUTUREREFERENCE.

Please contact your Heat-N-Glo dealer with any

questionsor concerns. Forthe numberof yournearest

Heat-N-Glodealer,pleasecall 1-888-427-3973.

Heat-N-Glo,a brand ofHearth &Home TechnologiesInc.

20802Kensington Blvd.,Lakeville,MN 55044

These instructions are only valid if the

following country symbol is on the appliance.

If this symbol is not present on the appliance,

it is necessary to refer to the technical

instructions which will provide the necessary

information concerning the modification of the

appliance to the conditions of use for the

country.

0087

These instructions are valid for the following

countries: GB, IE

WARNING:

IF THE INFORMATION IN THESE

INSTRUCTIONS IS NOT

FOLLOWED EXACTLY, A FIRE OR

EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE,

PERSONAL INJURY, OR DEATH.

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;

4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)

543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

SAFETY AND WARNING INFORMATION

READ and UNDERSTAND all instructions carefully before starting the installation.

FAILURE TO FOLLOWthese installation instructions may result in a possible fire

hazard and will void the warranty.

Prior to the first firing of the stove, READ the Using Your Fireplace section of theUsers

Guide.

DO NOT USE this appliance if any part has been under water. Immediately CALL a

qualified service technician to inspect the unit and to replace any part of the control

system and any gas control which has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should bePERFORMED by a qualified service person. The

appliance and flue system should beINSPECTED before initial use and at least

annually by a professional service person.

Always KEEP the appliance clear and free from combustible materials, petrol, and

other flammable vapors and liquids.

NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the

appliance CLEAR of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should beLOCATED out of traffic areas

and away from furniture and draperies. Clothing or flammable materialSHOULD NOT

BE PLACED on or near the appliance.

Children and adults should beALERTED to the hazards of high surface temperature

and shouldSTAYAWAYto avoid burns or clothing ignition. Young children should be

CAREFULLYSUPERVISED when they are in the same room as the appliance.

These unitsMUSTuseoneofthe fluingsystems describedin theInstalling theFireplace

section of theInstallersGuide. NO OTHERflue systems or componentsMAYBE USED.

This gas stove and flue assembly MUST be vented directly to the outside andMUST

NEVER be attached to a chimney serving a separate solid fuel burning appliance.

Each gas applianceMUST USE a separate flue system. Common flue systems are

PROHIBITED.

INSPECT the external terminal cap on a regular basis to make sure that no debris is

interfering with the air flow.

The glass door assembly MUST be in place and sealed, and the trim door assembly

MUST be in place on the stove before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door removed, cracked, or broken.

Replacement of the glass door should be performed by a licensed or qualified service

person. DO NOT strike or slam the glass door.

The glass door assembly SHALL ONLYbe replaced as a complete unit, as supplied

by the gas stove manufacturer. NO SUBSTITUTE material may be used.

DO NOT USE abrasive cleaners on the glass door assembly. DO NOT ATTEMPT to

clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified

service technician perform an appliance check-up at the beginning of each heating

season.

Any safety screen or guard removed for servicing must be replaced before operating

this appliance.

This appliance is intended for use on a gas installation with a governed meter.

Table of

Contents

Safety and Warning Information ................................... 2

Service Parts List .......................................................... 4

Section 1: Approvals and Regulations ........................ 6

Appliance Certification..................................................6

Installation Regulations ................................................6

Section 2: Getting Started ............................................ 7

Introducing the Heat-N-Glo Gas Fireplaces .................7

Pre-installation Preparation..........................................7

Section 3: Installing the Fireplace ............................... 9

Step 1 Locating the Fireplace....................................9

Step 2 Framing the Fireplace ..................................10

Step 3 Installing the Flue System ............................ 11

A. Flue System Approvals ............................ 11

B. Installing Flue Components .....................20

C. Flue Termination ......................................24

Step 4 Positioning, Leveling and

Securing the Fireplace .................................29

Step 5 The Gas Control Systems............................29

Step 6 The Gas Supply Line ....................................30

Step 7 Gas Pressure Requirements .......................31

Step 8 Wiring the Fireplace .....................................31

Step 9 Finishing........................................................32

Step 10

Installing Trim, Logs & Ember Material ........

Installing the Trim..........................................33

Positioning the Logs .....................................34

Placing the Ember Material ..........................36

Step 11 Before Lighting the Fireplace........................37

Step 12 Lighting the Fireplace ...................................37

After the Installation ......................................37

Section 4: Maintaining and Servicing

Your Fireplace .......................................... 38

Section 5: Troubleshooting ........................................ 40

u= Contains updated information.

*Partnumberlist onfollowingpage.

9 Log SetAssembly

(NG, LP) Exploded Parts Diagram

Service Parts SL-350TRS-CE-D

Beginning Manufacturing Date: 9-03

Ending Manufacturing Date: _______

16 5

11 12

13 14

ITEM PARTS SERIAL # PART NUMBER

Burner Orifice NG (#44C) 582-844

Burner Orifice LP (#55C) 582-855

Burner Orifice B (#56C) 582-856

1Wire Assembly 049-552A

2Burner NG 2033-007

2Burner B 2033-009

2Burner LP 2033-008

3Glass Door Assembly GLA-350TRS

4Log Grate 2033-013

5Base Refractory NG, LP 2033-105

6Hood 540-174

7Bottom Louver Assembly 540-257A

8Top Louver Assembly 540-256A

9Log Set Assembly LOGS-350CE-D

10 Log 1 SRV327-701

11 Log 2 SRV2033-701

12 Log 3 SRV705-703

13 Log 4 SRV530-716

14 Log 5 SRV438-724

15 Log 6 SRV540-704

16 Flexball Valve Assembly 302-330A

17 Mesh Assembly 540-382A

18 Piezo Ignitor 418-513

19 ON/OFF Rocker Switch 060-511

20 Burner Tube Assembly 383-302A

21 Valve NG 060-524

21 Valve LP 060-526

22 Pilot Assembly NG 529-510A

22 Pilot Assembly LP 529-511A

23 Junction Box 546-250A

24 Pilot Bracket 2033-103

25 Burner Neck Gasket 438-407

26 Valve Plate Gasket 530-431

27 Valve Bracket 529-169

Pilot Orifice NG 529-512

Pilot Orifice LP 529-513

ACCESSORIES

Extended Vertical Baffle Kit BAF-VERT

Wall Switch Kit, Off-white WSK-21

Wall Switch Kit, White WSK-21-W

Conversion Kit NG NGK-350TRSCE-D

Conversion Kit LP LPK-350TRSCE-D

Conversion Kit Butane BGK-350TRSCE-D

(NG, LP) Service Parts List

IMPORTANT: THISISDATED INFORMATION. The most current information is located on your dealers VIP site. When ordering,

supply serial and model numbers to ensure correct service parts.

SL-350TRS-CE-D

Appliance Certification

The Heat-N-Glo fireplace models discussed in this

Installers Guide have been tested to certification

standardsand listedbythe applicable laboratories.

CERTIFICATION

MODEL LABORATORY TYPE STANDARD

SL-350TRS-CE-D

Advantica Gas Fireplace 90/396/EEC

Installation Regulations

Before installation check that local distribution conditions, nature of gas and

pressure, and adjustment of the appliance are compatible.

This appliance must be installed with the rules in force, and used only in a

sufficiently ventilated space. Consult instructions before installation and use of

this appliance.

Approvals

and

Regulations

Heat-N-Glo direct flue gas fireplaces are designed to

operate with all combustion air siphoned from outside

of the building and all exhaust gases expelled to the

outside.

The information contained in this Installers Guide,

unless noted otherwise, applies to all models and gas

control systems.

Gas fireplace diagrams, including the dimensions, are

shown in this section.

This gas fireplace and its components are tested and

safe when installed in accordance with this Installers

Guide. Report to your dealer any parts damaged in

shipment, particularly the condition of the glass. Do

not install any unit with damaged, incomplete, or

substitute parts.

The flue system components and trim doors are

shipped in separate packages. The gas logs are

packaged separately and must be field installed.

Read all of the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benefit. Failure to follow these instructions

will void the owner’s warranty and may present a

fire hazard.

The Heat-N-Glo Fireplace Products, Inc. Warranty will

be voided by, and Heat-N-Glo Fireplace Products, Inc.

disclaims any responsibility for, the following actions:

•Installation of any damaged fireplace or flue system

component.

•Modification of the fireplace or direct flue system.

•Installation other than as instructed by Heat-N-Glo

Fireplace Products, Inc.

•Improper positioning of the gas logs or the glass

door.

•Installation and/or use of any component part not

manufactured and approved by Heat-N-Glo Fire-

place Products, Inc., not withstanding any indepen-

dent testing laboratory or other party approval of

such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A

FIRE HAZARD.

Introducing the

Heat-N-Glo

Gas Fireplaces

Pre-installation

Preparation

Getting

Started

8Figure 1. Diagram of the SL-350TRS-CE-D

RATING PLATE/LABELS

BOTTOM

GRILLE COVER

GAS

ACCESS

GAS

CONTROLS ELECTRICAL

ACCESS

VENT

COLLARS

TOP STANDOFFS

HOOD

CERAMIC

FIBER PAD

When planning a fireplace installation, it’s necessary to determine:

•Where the unit is to be installed.

•The flue system configuration to be used.

•Gas supply piping.

•Electrical wiring.

•Framing and finishing details.

•Whether optional accessories—devices such as a fan, wall switch, or

remote control—are desired.

If the fireplace is to be installed on carpeting or tile, or on any combustible

material other than wood flooring, the fireplace should be installed on a metal

or wood panel that extends the full width and depth of the fireplace.

8 in.

(203mm)

16-5/16 in.

(414mm)

8-13/16 in.

(223mm)

15-13/16 in.

(402mm)

22-11/16 in.

(577mm)

11-3/8in.

(289mm)

29-1/16 in.

(738mm)

14-11/16 in.

(374mm)

3-1/2in.

(90mm)

6-7/8in.

(174mm)

ELECTRICAL

ACCESS

30-5/8 in.

(776mm)

Ø6-5/8 in.

(167mm)

32-7/8in.

(837mm)

28-1/8in.

(714mm)

2-1/4 in.

(57mm)

5-5/8 in.

(143mm)

41-3/4in.

(1061mm)

21-1/2 in.

(542mm)

GAS LINE

ACCESS

AB CDE

83.7cm 41.3cm 72.8cm 100.1cm 141.6cm

Figure 2. Fireplace Dimensions, Locations, and

Space Requirements

1/2” MIN. (13mm)

3” MIN. (76mm)

Installing the

Fireplace

The diagram below shows space and clearance

requirements for locating a fireplace within a room.

Step 1

Locating the

Fireplace

TOP

STANDOFFS

INSTALLED

HEAT SHIELD

Figure 3. Heat Shield

NOTE:

Dimensions are

shown with the

sides, back

and/or corners

of the unit 1/2

inch from the

wall.

The heat shield must be

attached as shown if

combustible materials

are placed directly on

top standoffs (Figure 3).

The minimum clearance

to a perpendicular wall

extending past the face

of the fireplace is 7.62cm.

The back of the fireplac-

es may be recessed

into combustible con-

struction, as shown

below.

MODEL: SL-350TRS-CE-D RECESSED DEPTH: 41.3cm

Clearance Requirements

The top and back of the

fireplace are defined by

stand-offs.

Minimum Clearances from the Fireplace to Combustible Materials

Glass

Front Floor Back of

Fireplace Sides of

Fireplace Top of

Fireplace Ceiling

91.4cm 01.3cm 1.3cm 3.8cm 79cm

Framing should be

constructed of 2 X 4 lumber or heavier.

The framing headers may rest

on the fireplace stand-offs.

A B C D E

86.4 78.7 41.3 108.6 57.2

NOTE: DIMENSIONS SHOWN IN CM.

Figure 4. Framing Dimensions

Minimum Clearances from the Flue Pipe to

Combustible Materials

For Vertical

For Horizontal Sections Sections At Wall Firestops

Top Bottom Sides Top Bottom Sides

7.6 cm 2.54 cm 2.54 cm 2.54 cm 6.4 cm 1.3 cm 2.54 cm

Step 2

Framing the

Fireplace

Fireplace framing can be built before or after the

fireplaceis set inplace.Framingshould be positioned

to accommodate wall coverings and fireplace facing

material. The diagram below shows framing reference

dimensions.

CAUTION MEASURE FIREPLACE DIMENSIONS, AND

VERIFY FRAMING METHODS AND WALL

COVERING DETAILS, BEFORE FRAMING

CONSTRUCTION BEGINS.

The center of the framing hole is

one inch (2.54cm) above the center

of the horizontal flue pipe.

VENT

FRAMING

HOLE

Andere Handbücher für SL-350TRS-CE-D

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo LOGS-2531 Bedienungsanleitung

Heat & Glo

Heat & Glo 8000CF-OAK-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo RH-42 Series Bedienungsanleitung

Heat & Glo

Heat & Glo ST-HVB-CE Bedienungsanleitung

Heat & Glo

Heat & Glo SLR-C (COSMO) Bedienungsanleitung

Heat & Glo

Heat & Glo SUPREME-I30-SP Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO60 Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace HST-48D Bedienungsanleitung

Heat & Glo

Heat & Glo I30X-N-AU Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CLX-IPI-T Bedienungsanleitung

Heat & Glo

Heat & Glo PALOMA-BL Bedienungsanleitung

Heat & Glo

Heat & Glo Firebrick ESCAPE-I35 Bedienungsanleitung

Heat & Glo

Heat & Glo Cosmo SLR Bedienungsanleitung

Heat & Glo

Heat & Glo RHW-485 Bedienungsanleitung

Heat & Glo

Heat & Glo RUTHERFORD-50 Bedienungsanleitung

Heat & Glo

Heat & Glo EM-415 Bedienungsanleitung

Heat & Glo

Heat & Glo SLR-X-AU-L Bedienungsanleitung

Heat & Glo

Heat & Glo RH-36 Series Bedienungsanleitung

Heat & Glo

Heat & Glo 8000TV-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo 8000C-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo Phoenix42-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo SL-750TRSFHHIPI Bedienungsanleitung

Heat & Glo

Heat & Glo 8000TRLP-OAKIPI Bedienungsanleitung

Heat & Glo

Heat & Glo Crescent II Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch