Heat & Glo Pier-HVB-IPI Bedienungsanleitung

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev.M• 8/06 1

Models:

Pier-HVB-IPI

ST-HVB-IPI

LCOR-HVB-IPI

RCOR-HVB-IPI

Underwriters

Laboratories Listed

IntheCommonwealthofMassachusetts:

• installation must be performed by a licensed

plumberorgasfitter;

• a CO detector shall be installed in the room

where the appliance is installed.

- Do not store or use gasoline or other flam-

mablevaporsandliquidsinthevicinityofthis

oranyotherappliance.

- What to do if you smell gas

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Donotuseanyphoneinyourbuilding.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call

thefiredepartment.

- Installationandservicemustbeperformedbya

qualified installer, service agency, or the gas

supplier.

WARNING: IMPROPER INSTALLA-

TION, ADJUSTMENT, ALTERATION,

SERVICE OR MAINTENANCE CAN

CAUSE INJURY OR PROPERTY DAM-

AGE. REFER TO THIS MANUAL. FOR

ASSISTANCE ORADDITIONAL INFOR-

MATION CONSULT A QUALIFIED IN-

STALLER, SERVICEAGENCY, OR THE

GAS SUPPLIER.

READ THIS MANUAL BEFORE INSTALLING OR

OPERATING THISAPPLIANCE. THIS INSTALLERS

GUIDE MUST BE LEFT WITH APPLIANCE FOR

FUTUREREFERENCE.

1.This appliance may be installed in an af-

termarket,permanentlylocated,manufac-

tured(mobile)home,wherenotprohibited

bylocalcodes.

2. Thisapplianceisonlyfor usewiththetype

of gas indicated on the rating plate. This

appliance is not convertible for use with

othergases,unlessacertifiedkitisused.

Please contact your Heat-N-Glo dealer with any

questionsorconcerns.For the number ofyournearest

Heat-N-Glodealer,please call 1-888-427-3973.

Heat &Glo,abrandof Hearth & HomeTechnologiesInc.

20802KensingtonBoulevard,Lakeville,MN55044

WARNING: IF THE INFORMATION

IN THESE INSTRUCTIONS IS NOT

FOLLOWED EXACTLY,AFIRE OR

EXPLOSION MAY RESULT CAUS-

ING PROPERTY DAMAGE, PER-

SONAL INJURY, OR DEATH.

Owner’s Manual

Installation and Operation

Thisproductmaybecoveredbyoneormoreofthefollowingpatents:(United States)4593510, 4686807, 4766876, 4793322, 4811534,5000162,5016609,5076254,5113843,5191877,5218953,5263471,

5328356,5341794,5347983,5429495,5452708,5542407,5601073,5613487,5647340,5688568,5762062,5775408,5890485,5931661,5941237,5947112,5996575,6006743,6019099,6048195,6053165,

6145502,6170481,6237588,6296474,6374822, 6413079, 6439226,6484712,6543698,6550687,6601579,6672860,6688302B2,6715724B2,6729551,6736133,6748940,6748942,6769426,6774802,

6796302,6840261,6848441,6863064,6866205, 6869278, 6875012, 6880275, 6908039,6919884,D320652,D445174,D462436; (Canada) 1297749,2195264, 2225408, 2313972; (Australia) 780250,

780403,1418504 or otherU.S.and foreign patentspending.

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06

These units MUST use one of the vent systems

described in the Installing the Fireplace section of

the Installers Guide.NO OTHER vent systems or

components MAY BE USED.

This gas fireplace and vent assembly MUST be

vented directly to the outside and MUST NEVER be

attached to a chimney serving a separate solid fuel

burning appliance. Each gas appliance MUST USE

a separate vent system. Common vent systems are

PROHIBITED.

INSPECT the external vent cap on a regular basis to

make sure that no debris is interfering with the air

flow.

The glass door assembly MUST be in place and

sealed, and the trim door assembly MUST be in

place on the fireplace before the unit can be placed

into safe operation.

DO NOT OPERATE this appliance with the glass

door removed, cracked, or broken. Replacement of

the glass door should be performed by a licensed

or qualified service person. DO NOT strike or slam

the glass door.

The glass door assembly SHALL ONLY be

replaced as a complete unit, as supplied by the gas

fireplace manufacturer. NO SUBSTITUTE material

may be used.

DO NOT USE abrasive cleaners on the glass door

assembly. DO NOT ATTEMPT to clean the glass

door when it is hot.

Turn off the gas before servicing this appliance. It is

recommended that a qualified service technician

perform an appliance check-up at the beginning of

each heating season.

Any safety screen or guard removed for servicing

must be replaced before operating this appliance.

DO NOT place furniture or any other combustible

household objects within 36 inches of the fireplace

front.

READ and UNDERSTAND all instructions carefully

before starting the installation. FAILURE TO

FOLLOW these installation instructions may result

in a possible fire hazard and will void the warranty.

Prior to the first firing of the fireplace, READ the

Using Your Fireplace section of the Owners Guide.

DO NOT USE this appliance if any part has been

under water. Immediately CALL a qualified service

technician to inspect the unit and to replace any part

of the control system and any gas control which has

been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a

qualified service person. The appliance and venting

system should be INSPECTED before initial use

and at least annually by a professional service

person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding

material, etc. It is IMPERATIVE that the unit’s

control compartment, burners, and circulating air

passageways BE KEPT CLEAN to provide for

adequate combustion and ventilation air.

Always KEEP the appliance clear and free from

combustible materials, gasoline, and other

flammable vapors and liquids.

NEVER OBSTRUCT the flow of combustion and

ventilation air. Keep the front of the appliance

CLEAR of all obstacles and materials for servicing

and proper operations.

Due to the high temperature, the appliance should

be LOCATED out of traffic areas and away from

furniture and draperies. Clothing or flammable

material SHOULD NOT BE PLACED on or near the

appliance.

Children and adults should be ALERTED to the

hazards of high surface temperature and should

STAY AWAY to avoid burns or clothing ignition.

Young childrenshould be CAREFULLYSUPERVISED

when they are in the same room as the appliance.

Safety and Warning Information

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06 3

Safety and Warning Information.................................................. 2

Service Parts List ......................................................................... 4

Approvals and Codes ................................................................ 13

ApplianceCertification ................................................................................. 13

InstallationCodes ........................................................................................ 13

HighAltitude Installations............................................................................. 13

Getting Started............................................................................ 14

IntroducingtheHeat&GloGasFireplaces .................................................. 14

Pre-installPreparation ................................................................................. 14

Installing the Fireplace ............................................................... 18

Step 1. Locating the Fireplace .................................................................... 18

Step 2. Framing the Fireplace..................................................................... 18

Step 3. Installing the Vent System.............................................................. 21

A. Vent SystemApprovals ......................................................... 21

B. Installing Vent Components ................................................... 28

C. VentTermination.................................................................... 30

Step 4. Positioning,Leveling, and Securing the Fireplace ........................... 33

Step 5. The Gas Control System ................................................................ 33

Step 6. The Gas Supply Line ...................................................................... 34

Step 7. Gas Pressure Requirements........................................................... 34

Step 8. Wiring the Fireplace........................................................................ 35

Step 9. Finishing......................................................................................... 37

Step 10. Installing Trim, Logs & Ember Material .......................................... 38

InstallingtheTrim .......................................................................... 38

PositioningtheLogs...................................................................... 38

Shutter Settings ............................................................................ 38

GlassSpecifications...................................................................... 38

PlacingtheEmberMaterial ........................................................... 39

EmberLightBulbReplacement ..................................................... 39

Step 11. Before Lighting the Fireplace........................................................ 40

Step 12. Lighting the Fireplace ................................................................... 40

AftertheInstallation ..................................................................................... 40

Maintaining and Servicing Your Fireplace................................41

Î= Containsupdatedinformation.

Table of Contents

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06 13

Appliance Certification

TheHeat& Glo fireplacemodelsdiscussedin this Installers

Guidehavebeentested tocertificationstandardsand listed

bytheapplicablelaboratories.

Certification

MODELS: PIER-HVB-IPI, ST-HVB-IPI,

LCOR-HVB-IPI, RCOR-HVB-IPI

LABORATORY: UnderwritersLaboratories

TYPE: Vented Gas Fireplace Heater

STANDARD: ANSI Z21.88•CGA2.22•UL307B

Installation Codes

Thefireplaceinstallationmustconformto localcodes.Before

installing the fireplace, consult the local building code

agency to ensure that you are in compliance with all

applicable codes, including permits and inspections.

Intheabsence oflocalcodes,the fireplaceinstallationmust

conformtotheNational FuelGasCodeANSI Z223.1(inthe

United States) or the CAN/CGA-B149 Installation Codes

(in Canada). The appliance must be electrically grounded

in accordance with local codes or, in the absence of local

codes with the National Electric CodeANSI/NFPANo. 70

(inthe UnitedStates),ortothe CSAC22.1CanadianElectric

Code(inCanada).

Thesemodelsmaybeinstalledin a bedroom or bed-sitting

room in the U.S.A. and Canada.

1Approvals and

Codes

HighAltitude Installations

U.L. Listed gas appliances are tested and approved with-

outrequiringchangesforelevationsfrom0to2,000feetin

the U. S.A. and in Canada.

Wheninstallingthisapplianceatanelevationabove2,000

feet, it may be necessary to decrease the input rating by

changingtheexistingburnerorificetoasmallersize.Input

rate should be reduced by 4% for each 1000 feet above a

2000 foot elevation in the U.S.A. or 10% for elevations

between2000and 4500feetinCanada.Iftheheating value

of the gas has been reduced, these rules do not apply. To

identify the proper orifice size, check with the local gas

utility.

Ifinstalling this appliance at an elevation above 4,500 feet

(in Canada), check with local authorities.

Heat & Glo Quality Systems

registeredby SGS ICS

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06

2Getting Started

Introducing the Heat & Glo Gas Fireplaces

Heat&Glodirectventgasfireplaces are designed to oper-

ate with all combustion air siphoned from outside of the

building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless

noted otherwise, applies to all models and gas control

systems.Gasfireplace diagrams,includingthe dimensions,

are shown in this section.

Pre-install Preparation

Thisgas fireplace and its components are tested and safe

when installed in accordance with this Installers Guide.

Report to your dealer any parts damaged in shipment,

particularly the condition of the glass. Do not install any

unit with damaged, incomplete, or substitute parts.

Theventsystemcomponentsare shippedinseparatepack-

ages. The gas logs are packaged separately and must be

fieldinstalled.

Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the

installation to ensure maximum safety and benefit.

Failure to follow these instructions will void the own-

er’s warranty and may present a fire hazard.

TheHeat&GloWarrantywillbevoidedby, and Heat & Glo

disclaims any responsibility for, the following actions:

• Installation of any damaged fireplace or vent system

component.

• Modification of the fireplace or direct vent system.

• Installation other than as instructed by Heat & Glo.

• Improper positioning of the gas logs or the glass door.

• Installationand/oruseof any componentpartnotmanu-

factured and approved by Heat & Glo, not withstanding

anyindependenttestinglaboratoryorotherpartyapproval

of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE

HAZARD.

When planning a fireplace installation, it’s necessary

to determine:

•Where the unit is to be installed.

•The vent system configuration to be used.

•Gas supply piping.

•Electricalwiring.

•Framingandfinishingdetails.

•Whether optional accessories—devices such as a fan,

wallswitch, or remote control—are desired.

If the fireplace is to be installed on carpeting or tile,

or on any combustible material other than wood

flooring, the fireplace should be installed on a metal

or wood panel that extends the full width and depth

of the fireplace.

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06 15

Figure 1. Diagram of the PIER-HVB-IPI

42-5/8

(1082mm)

Ø8

(204mm)

(305mm)

ELECTRICAL

ACCESS

GAS LINE

ACCESS

34-3/4

(882mm)

4-1/16

(102mm)

4-1/2

(114mm) 4-3/4

(121mm)

2-5/16

(58mm) 37-7/16

(950mm)

32-5/16

(820mm) 21

(533mm)

(1067mm)

17-15/16

(455mm)

(610mm)

(533mm)

5-1/4

(133mm)

1/2

(13mm)

(2)

(306mm)

Ø8

(204mm)

8-1/2

(216mm)

REAR VENT

COLLARS

ELECTRICAL

ACCESS

GAS LINE

ACCESS

GAS CONTROLS

& LABELS

SIDE GLASS

DOOR

TOP STANDOFFS

TOP VENT

COLLARS

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06

Figure 2. Diagram of the ST-HVB-IPI

5-14

(133mm)

(306mm)

1/2

(13mm)

(4)

46-5/8

(1183mm)

(1067mm) 32-5/16

(820mm)

(533mm)

36-3/16

(919mm)

2-5/16

(58mm)

4-3/4

(121mm)

4-1/16

(102mm)

4-1/2

(114mm)

ELECTRICAL

ACCESS

GAS LINE

ACCESS

(305mm)

4-1/2

(114mm)

2-9/16

(64mm)

(610mm)

8-1/2

(216mm)

34-3/4

(882mm)

Ø8

(204mm)

Ø8

(204mm)

REAR VENT

COLLARS

ELECTRICAL

ACCESS

GAS LINE

ACCESS

GAS CONTROLS

& LABELS SIDE GLASS

DOOR

TOP STANDOFFS

TOP VENT

COLLARS

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06 17

Figure 3. Diagram of the LCOR-HVB-IPI and RCOR-HVB-IPI

(305mm)

Ø8

(204mm)

34-3/4

(882mm)

4-3/4

(121mm)

37-7/16

(950mm)

ELECTRICAL

ACCESS

GAS LINE

ACCESS

42-5/8

(1082mm

2-5/16

(58mm)

(533mm)

24-1/8

(612mm)

8-1/2

(216mm)

(533mm)

(1066mm

32-5/16

(820m)

17-15/16

(455mm)

2-9/16

(64mm)

1/2

(13mm)

(4)

5-1/4

(133mm)

(305mm)

29-1/4

(743mm)7-1/4

(184mm)

Ø8

(204mm)

(254mm)

REAR VENT

COLLARS

ELECTRICAL

ACCESS

GAS LINE

ACCESS

GAS CONTROLS

& LABELS

END GLASS

DOOR

TOP STANDOFFS

TOP VENT

COLLARS

SIDE GLASS

DOOR

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06

3Installing the Fireplace

Step 1. Locating the Fireplace

The diagram below shows space and clearance require-

ments for locating a fireplace within a room.

Figure 4A. Fireplace Dimensions and Locations

36"

GLASS

36"

GLASS

36"

GLASS

36"

GLASS

36"

PIER-HVB-IPI

TOP VIEW RCOR-HVB-IPI

TOP VIEW

LCOR-HVB-IPI

TOP VIEW

ST-HVB-IPI

TOP VIEW

Clearance Requirements

The top, back, and sides of the fireplace are defined by

stand-offs.Theminimumclearanceto a perpendicular wall

extendingpastthe faceofthefireplaceis oneinch(25mm).

ThemetalendsofthefireplacemayNOT berecessedinto

combustible construction.

Note: Refer to Figure 4B for dimensionsandappliance

locations if installing a Pier-HVB unit with a Catalina

shelf and/or marble package.

Note: Refer to the Catalina installation instruction

included with kit for assembly and installation. Figure 4B.

50-1/2 in.

34-1/2 in.

7 in.

47-1/2 in.

45-1/4 in.

13/16 in.

Marble sizes (inches):

Header.................................. 26 x 8

Side headers ..................45-1/2 x 8

Legs................................33-1/2 x 7

45 -1/4 in.

(1149mm)

FINISHED

WALL

Fireplace Locations/Dimensions with

Catalina Shelf/Marble Package ONLY

Note: This location diagram MUST be followed when in-

stalling a Pier-HVB with a Catalina shelf/marble package

since the fireplace is installed further from finished wall.

Heat&Glo • PIER-HVB-IPI,ST-HVB-IPI,LCOR-HVB-IPI,RCOR-HVB-IPI • 2006-900 Rev. M• 8/06 19

Minimum Clearances

from the Fireplace to Combustible Materials

Inches mm

Glass Sides or Ends.......... 36 .................... 914

Floor ................................... 0 ....................... 0

RearVent...........................1/2 ..................... 13

Metal Sides or Ends ..........1/2..................... 13

Top................................... 2 1/2 ................... 64

Ceiling* .............................. 31 .................... 787

For minimum clearances, see the direct vent termination

clearance diagrams on pages 31 and 32 in this manual.

Minimum Clearances

from the Vent Pipe to Combustible Materials

Inches mm

Vertical Sections. ............. 1 ................ 25

Horizontal Sections

Top..................................... 3 ................ 75

Bottom ............................... 1 ................ 25

Sides ................................. 1 ................ 25

At Wall Firestops

Top.................................. 2 1/2 ............63.7

Bottom ..............................1/2............... 13

Sides ................................. 1 ................ 25

* The clearance to the ceiling is measured from the top of

the unit, excluding the standoffs (see Figures 37 & 38).

Thedistancefromtheunit to combustible constructionisto

be measured from the unit outer wrap surface to the com-

bustible construction, NOT from the screw heads that se-

curetheunittogether.

WARNING: FRAMING DIMENSIONS ASSUME

USE OF 1/2 INCH THICK WALL COVERING

MATERIALSONEXTERIOR OFFRAMINGONLYAND

NO SHEETROCK ON INTERIOR OF FRAMING.

Step 2. Framing the Fireplace

Fireplaceframingcanbe builtbeforeorafter thefireplaceis

set in place. Framing should be positioned to accommo-

date wall coverings and fireplace facing material. The dia-

grambelowshowsframing referencedimensions.

CAUTION: MEASURE FIREPLACE DIMENSIONS AND

VERIFY FRAMING METHODS AND WALL COVERING

DETAILS BEFORE FRAMING.

Andere Handbücher für Pier-HVB-IPI

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo ST-550T-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CMOD-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo LUX36 Bedienungsanleitung

Heat & Glo

Heat & Glo Cosmo SLR Bedienungsanleitung

Heat & Glo

Heat & Glo PIER-40 Bedienungsanleitung

Heat & Glo

Heat & Glo SLR-C (COSMO) Bedienungsanleitung

Heat & Glo

Heat & Glo SL-3X-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo ST-550TM-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo Firebrick ESCAPE-I35 Bedienungsanleitung

Heat & Glo

Heat & Glo FB-GRAND-S Bedienungsanleitung

Heat & Glo

Heat & Glo 8000TR-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo Phoenix42-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36H-C Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CMOD-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo SL-750TRSFHHIPI Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CL-IFTLP-S Bedienungsanleitung

Heat & Glo

Heat & Glo ST-550TM-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo XLR-PB-CE Bedienungsanleitung

Heat & Glo

Heat & Glo 8000CF-OAK-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo MEZZO36 Bedienungsanleitung

Heat & Glo

Heat & Glo 350TRSI-AUF Bedienungsanleitung

Heat & Glo

Heat & Glo 6000PLUS Bedienungsanleitung

Heat & Glo

Heat & Glo MEZZO-1000-AU Bedienungsanleitung

Heat & Glo

Heat & Glo Cosmo SLR Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch