Heat & Glo SL-550TRSI-AUE Bedienungsanleitung

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

INSTALLATION AND OPERATION INSTRUCTIONS

THIS PRODUCT MAY BE COVERED BY ONE OR MORE OF THE FOLLOWING PATENTS:

(United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495,

5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502,

6170481,6237588,6296474,6374822, 6413079,6439226, 6484712,6543698, 6550687,6601579, 6672860,6688302B2, 6715724B2,6729551,6736133, 6748940,6748942, D320652,

D445174, D462436; (Canada) 1297749, 2195264, 2225408; (Australia) 543790;586383; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

HEAT & GLO, a brand of Hearth & Home Technologies Inc.

20802 Kensington Boulevard, Lakeville, MN 55044, USA, www.heatnglo.com

THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED

BY HOMEOWNER FOR OPERATION AND MAINTENANCE.

MODEL: SL-550TRSI-AUE

AUSTRALIAN GAS ASSOCIATION CERTIFIED

CERTIFICATE NUMBER 5666

2Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

MODEL SL-550TRSI-AUE

IS AUSTRALIAN GAS ASSOCIATION

APPROVED FOR NATURAL GAS OR

PROPANE AS A BALANCED FLUE

HEATER.

Refer to the appliance data plates for gas

consumptions and pressures.

Installationof thisapplianceshould only be

carried out by an authorized person in ac-

cordance with the manufacturer's instruc-

tions. Appliance is to be installed in full

compliance with the National Gas Installa-

tion StandardAS5601, the manufacturer's

instructions, and any local authorities' re-

quirements for gas, electrical and building

regulations.

This appliance and its components are

tested and safe when installed in accor-

dancewith this Installation Manual. Report

to your dealer any parts damaged in ship-

ment, speciﬁcally check glass condition.

Thegaslogsandﬂuesystemcomponents

are in separate packages. Read all in-

structions before starting installation and

follow these instructions carefully during

installationto ensure maximumbeneﬁtand

safety. Failure to follow them will void your

warranty and may present a ﬁre hazard.

TheHeat& Glo, a brand of Hearth & Home

Technologies Inc. warranty will be voided

by, and Heat & Glo, a brand of Hearth &

Home Technologies Inc. disclaims any re-

sponsibility for the following actions:

• Installation of any damaged heater or

ﬂue system component

• Modiﬁcation of the heater or balanced

ﬂue system installation other than as

instructed by Heat & Glo, a brand of

Hearth & Home Technologies Inc.

• Improper positioning of the gas logs or

the glass door

• Installationand/oruse ofanycomponent

part not manufactured or approved by

Heat & Glo, brand of Hearth & Home

Technologies Inc.,not withstanding any

independent testinglaboratory or other

party approval of such componentpart

or accessory.

PLEASE READ THIS MANUAL BEFORE INSTALLING

AND USING THIS APPLIANCE.

IMPORTANT: Read all instructions carefully before starting installation.

Failure to follow these installation instructions may result in a possible ﬁre

hazard and will void the warranty. Save this manual for future reference.

Heat & Glo, a brand of Hearth & Home Technologies, Inc.

20802 Kensington Blvd., Lakeville, MN 55044, USA

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

Î= Contains updated information.

TABLE OF CONTENTS

1.0 Installation Instructions .......................................................................................5

1.1 Introduction...................................................................................................6

1.2 Flue System Approvals and Installation........................................................8

1.3 Connecting the Gas Supply........................................................................23

1.4 Ignition System Wiring................................................................................24

1.5 Blower ........................................................................................................25

1.6 Finishing.....................................................................................................26

1.7 Installer Testing...........................................................................................27

1.8 Log Placement............................................................................................28

2.0 Operating Instructions.......................................................................................31

2.1 Safety and Lighting Information..................................................................32

2.2 Power Outage.............................................................................................33

2.3 Fan Operation.............................................................................................33

3.0 Servicing and Maintenance...............................................................................33

3.1 Removal of Covers for Servicing................................................................34

3.2 Removal of Components for Service..........................................................34

3.3 Parts Replacement.....................................................................................34

3.4 Adjustments and Replacement Parts .........................................................34

3.5 Maintenance Tasks.....................................................................................35

3.6 Troubleshooting..........................................................................................36

4.0 Replacement Parts ...........................................................................................37

Limited Warranty...............................................................................................40

4Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

Figure 1. Diagram of SL-550TRSI-AUE

408 mm

593 mm

671mm

913 mm

402 mm

327 mm

653 mm

93 mm

178 mm

58 mm

153 mm

790 mm

414 mm 223 mm

168 mm

816 mm

877 mm

1035 mm

GAS LINE

ACCESS ELECTRICAL

ACCESS

203 mm

TOP STANDOFFS

DRESS GUARD

ACCESS DOOR

GAS LINE ACCESS

GAS CONTROLS

ELECTRIC ACCESS

DATA BADGE & LABELS

HOOD

FLUE COLLAR COVER PLATE

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

Figure 2. Heater Dimensions, Locations, and Space

Requirements

1.0 INSTALLATION INSTRUCTIONS

In planning the installation for the heater it is neces-

sary to determine where the unit is to be installed, the

type of ﬂue system to be used (straight out, corner,

or elevated), and whether optional accessories (wall

switch or remote control) are desired. Gas supply

piping should also be planned. Refer to the appliance

data plate on the base pan of the heater for all gas

pressures and input rate information.

The heater can be mounted on any of the following

surface:

1. A ﬂat surface (minimum 6 mm base).

2. Four (4) corner supports.

(Example: Four (4) concrete masonry blocks). These

supports must be positioned so they contact all four

(4) perimeter edges on the bottom of the unit.

Heaterframingcanbebuilt beforeor aftertheheater is

set in place. Framing should be positioned to accom-

modate wall covering and heater facing material. The

heater framing should be constructed of 2" X 4" (51 x

102 mm) lumber or heavier. The framing headers may

restonthe heaterstandoffs.Refer to Figure2 and Fig-

ure 4 for heater and framing reference dimensions.

NOTE: Not intended for heater insert.

Top Flue

Rear Flue

76 mm MIN.

AB C D E

Millimeter 940 413 749 1070 1511

AB C D E

Millimeter 940 413 889 1219 1803

12.5 mm MIN.

25 mm MIN.

Minimum Clearances

from the Heater to Combustible Materials

Glass Front ........................................914 mm

Floor .......................................................0 mm

Rear......................................................13 mm

Sides.....................................................13 mm

Top .......................................................86 mm

Ceiling*...............................................787 mm

*Theclearance toceiling ismeasured fromthe topof

the unit, excluding the standoffs (see Figure 30).

For minimum clearances, see the balanced ﬂue termi-

nation clearance in Figure 23 and 28.

Minimum Clearances

from the Vent Pipe to Combustible Materials

Vertical Sections.................................25 mm

Horizontal Sections

Top........................................................75 mm

Bottom..................................................25 mm

Sides.....................................................25 mm

At Wall Firestops

Top........................................................75 mm

Bottom..................................................25 mm

Sides.....................................................25 mm

6Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

Figure 3. Framing Dimensions

Framing should be constructed

of 2 X 4 lumber or heavier.

The framing headers

may rest on the heater

stand-offs.

A B C D* E*

940 mm 883 mm 420 mm 1035 mm 593 mm

*NOTE: This dimension is to the center of the ﬂue pipe. The

center of the framing hole MUST BE 25.4 mm above

the center of the horizontal ﬂue pipe.

CAUTION: Measure heater dimensions, and verify

framingmethods andwall coveringdetails beforefram-

ing construction begins.

1.1 INTRODUCTION

This model is designed to operate with all combustion

air being siphoned from the outside of the building

and all exhaust gases expelled to the outside of the

building.

WARNING: THIS UNIT IS NOT FOR USE WITH

SOLID FUEL.

These units MUST use the ﬂue termination described

in the ﬂueing section of the manual.

The control system for this model is an electronic ig-

nition type. It consists of a gas control valve/variable

regulator, a pilot/sensor/electrode and an ON/OFF

switch. The controls are located behind the access

door. Rotate the door down to open. See Figure 1.

Minimum inlet gas supply pressure for purpose of

input adjustment is 1.13 kPa for natural gas and 2.75

kPa for propane. Manifold (outlet) pressures should

be set at .8 kPa for natural gas models and 2.36 kPa

for propane models.

FLUE

FRAMING

HOLE

WALL STUD

86 mm

76 mm

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

NOTES: 1. All distances are measured vertically or horizontally along the wall to a point

in line with the nearest part of the terminal.

2. Prohibited area below electricity meter or fuse box extends to ground level.

3. See clause 5.13.6.6 for restrictions on a ﬂue terminal under a roofed area.

4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a ﬂue

terminal to a LP Gas cylinder. A ﬂue terminal is considered to be a source of ignition.

MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS

OR THE FLUE TERMINALS OF OUTDOOR APPLIANCES

Figure 4.

a - Below eaves, balconies or other projections: MIN. CLEARANCE (mm)

Appliances to 50 MJ/h input...................................................................................................300

Appliances over 50 MJ/h input...............................................................................................500

b - From the ground or above a balcony.........................................................................................300

c - From a return wall or external corner.........................................................................................500

d - From a gas meter (M)..............................................................................................................1000

e - From an electricity meter or fuse box (P)...................................................................................500

f - From a drain or soil pipe............................................................................................................150

g - Horizontally from any building structure (unless appliance approved

for closer installation) or obstruction facing a terminal...............................................................500

h - From any other ﬂue terminal, cowl, or combustion air intake ....................................................500

j - Horizontally from an openable window, door, non-mechanical air

inlet, or any other opening into a building, with the exception of

sub-ﬂoor ventilation:

Appliances up to 150 MJ/h input............................................................................................500

Appliances over 150 MJ/h input...........................................................................................1500

k - From a mechanical air inlet, including a spa blower...............................................................1500

n - Vertically below an openable window, non-mechanical air

inlet or any other opening into a building, with the exception of...................................... See table

sub-ﬂoor ventilation................................................................................................................ below

T= Flue terminal M= Gas meter Shading indicates prohibited

I= Mechanical air inlet P= Electricity meter or fuse box areas for ﬂue terminals

openable

window

door

kdb

See note 2

See note 3

CLEARANCE 'n' (mm)

Space Heaters All other appliances

Up to 50 MJ/h input Up to 50 MJ/h input Over 50 MJ/h input and

Up to 150 MJ/h input Over 50 MJ/h input

150 500 1000 1500

8Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

TABLE 1

1.2 FLUE SYSTEM APPROVALS

Thesemodelshaveﬂuestartingcollarson boththe top

and the back of the unit. Depending upon the instal-

lation, decide which ONE set of starting collars will be

usedtoattach theﬂue system.The startingcollar seal-

ing cap must remain on the starting collar NOT used.

These models use SLP series direct ﬂue components

whenusingthe TOP ﬂue collars andDVP seriesdirect

ﬂue components when using the REAR ﬂue collars.

WARNING: YOU MUST NOT MIX DVP-SERIESAND

SLPSERIES COMPONENTS INANY FLUESYSTEM

CONFIGURATION.

Approved ﬂue system components are labeled for

identiﬁcation. NO OTHER FLUEING SYSTEMS OR

COMPONENTS MAY BE USED. Detailed installation

instructions are included with each ﬂue termination kit

and should be used in conjunction with this manual.

Figure 5 below shows ﬂue system components and

terminations.

Identifying Flue Components

The ﬂue systems installed on this gas heater may

include one, two, or three 90° elbow assemblies. The

relationships of vertical rise to horizontal run in ﬂue

conﬁgurations using 90° elbows MUST BE strictly

adhered to. The rise to run relationships are shown

in the ﬂueing drawings and tables on the next few

pages.

WARNING: THIS GAS APPLIANCE AND FLUE AS-

SEMBLY MUST FLUE DIRECTLY TO THE OUTSIDE

AND MUST NEVER BEATTACHED TOA CHIMNEY

SERVING A SEPARATE SOLID FUEL BURNING

APPLIANCE. EACH GAS APPLIANCE MUST USE

ASEPARATE FLUE SYSTEM-COMMON FLUE SYS-

TEMS ARE PROHIBITED.

CAUTION: UNDER NO CONDITION SHOULD COM-

BUSTIBLE MATERIALBE CLOSER THAN76 MMAT

WALL FIRE-STOPS FROM THE TOP OF THE PIPE

OR 25 MM TO THE SIDESAND THE BOTTOM FOR

HORIZONTAL SECTIONS OF THIS FLUE SYSTEM.

VERTICAL SECTIONS OF THIS SYSTEM REQUIRE

AMINIMUM OF 25 MM CLEARANCE TO COMBUS-

TIBLE MATERIALS ALL AROUND THE PIPE.

For alternative installations, other than depicted, con-

tact your dealer for further information.

RefertoFigure4forrequiredclearancestoﬂueterminals.

Figure 5. Flue Components and Terminations

MODEL

SL-550TRSI-AUE

FLUE TERMINATION APPROVALS

DVP-TRAP2 & SLP-TRAP2 HORIZONTAL TERMINATION CAP

DVP-TVHW & SLP-TVHW VERTICAL TERMINATION CAP

HORIZONTAL

TERMINATION

WALL FIRESTOP

90 DEGREE

ELBOW

VERTICAL

TERMINATION STORM COLLAR

ROOF FLASHING

HORIZONTAL PIPE

SUPPORT

PIPE LENGTH

WALL BRACKET

CEILING

FIRESTOP

DVP SERIES

SLP-TVHW

SLP-TRAP2

SLP SERIES

DVP-TRAP2

DVP-TVHW

Flue system termination kits

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

NOTE: PIPES OVERLAP32 mm AT EACH JOINT

319 mm

286 mm

184 mm

32 mm TYP

13 mm TYP

217 mm

DVP36

DVP48

1219 mm

610 mm

914 mm

102 mm

152 mm

DVP4

DVP6

305 mm

DVP12

51 mm

MIN

DVP12A

310 mm

MAX

DVP24

251 mm

45.0º

260 mm

DVP45

362 mm

DVP90ST

Figure 6. DVP-Series Balanced Flue Component Speciﬁcations (127 mm inner pipe / 203 mm outer pipe)

10 Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. K • 10/08

Figure 7. SLP Series Balanced Flue Component Speciﬁcations (102 mm inner pipe / 168 mm outer pipe)

167 mm

152 mm

165 mm

248 mm

235 mm

184 mm

133 mm

641 mm

946 mm

1251 mm

337 mm

168 mm

SLP90

SLP12

SLP6

SLP4

SLP24 SLP36 SLP48

SLP12A

SLP6A

Note: Pipes overlap 34.93 mm at each joint.

Andere Handbücher für SL-550TRSI-AUE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo 550TRSI-AUF Bedienungsanleitung

Heat & Glo

Heat & Glo R-4INS Bedienungsanleitung

Heat & Glo

Heat & Glo NORTH STAR Handbuch

Heat & Glo

Heat & Glo RED40-N-AU Bedienungsanleitung

Heat & Glo

Heat & Glo MONTANA MONTANA-36 Bedienungsanleitung

Heat & Glo

Heat & Glo CURVE-100S-HS Bedienungsanleitung

Heat & Glo

Heat & Glo NORTHSTAR-BK Bedienungsanleitung

Heat & Glo

Heat & Glo SOLARIS36-ST Bedienungsanleitung

Heat & Glo

Heat & Glo SL-750TRSFHHIPI Bedienungsanleitung

Heat & Glo

Heat & Glo 6000C-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo SL-5LP-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo 6000GLX series Bedienungsanleitung

Heat & Glo

Heat & Glo 6000G-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo SUPREME-N-I30AU Bedienungsanleitung

Heat & Glo

Heat & Glo CF230E-B Bedienungsanleitung

Heat & Glo

Heat & Glo Heat & Glo XLR-PLUS-N-AU Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace HST-48D Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo ESCAPE-I35-C Bedienungsanleitung

Heat & Glo

Heat & Glo TRUE-36G-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo SLF-550TR-IPI-E Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace HST-48D Bedienungsanleitung

Heat & Glo

Heat & Glo BIR50 Bedienungsanleitung

Heat & Glo

Heat & Glo Pier-HVB-IPI Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch