Heat & Glo Townsend I Montageanleitung

- Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of

this or any other appliance.

-What to do if you smell gas

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call

the fire department.

- Installation and service must be performed by a

qualified installer, service agency, or the gas

supplier.

Heat-N-Glo Fireplace

Models:

Townsend I and II

Installers Guide

WARNING: IMPROPER INSTALLA-

TION, ADJUSTMENT, ALTERATION,

SERVICE OR MAINTENANCE CAN

CAUSE INJURY OR PROPERTY DAM-

AGE. REFER TO THIS MANUAL. FOR

ASSISTANCE OR ADDITIONAL INFOR-

MATION CONSULT A QUALIFIED

INSTALLER, SERVICE AGENCY, OR

THE GAS SUPPLIER.

402-982-A 11/98

READ THIS MANUAL BEFORE INSTALLING

OR OPERATING THIS APPLIANCE. THIS

INSTALLERS GUIDE

MUST BE LEFT WITH

THE APPLIANCE FOR FUTURE REFERENCE.

1. This appliance may be installed in an

aftermarket, permanently located,

manufactured (mobile) home, where

not prohibited by local codes.

2.This appliance is only for use with the

type of gas indicated on the rating

plate. This appliance is not convertible

for use with other gases, unless a

certified kit is used.

Please contact your Heat-N-Glo dealer for any

questionsorconcerns.Forthenumberofyour

nearest

Heat-N-Glo dealer, please call 612-890-8367.

Heat-N-Glo, a division of Hearth Technologies Inc.

6665 West Highway 13, Savage, MN 55378

WARNING:IFTHEINFORMATIONIN

THESEINSTRUCTIONSIS NOT

FOLLOWEDEXACTLY,AFIRE OR

EXPLOSIONMAYRESULTCAUSING

PROPERTYDAMAGE,PERSONAL

INJURY,ORDEATH.

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;

4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia) 543790; 586383;

(Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

Underwriters

Laboratories Listed

SAFETY AND WARNING INFORMATION

READ

and

UNDERSTAND

all instructions carefully before starting the installation.

FAILURE TO FOLLOW

these installation instructions may result in a possible fire

hazard and will void the warranty.

Prior to the first firing of the fireplace,

READ

the Using Your Fireplace section of the

Owners Guide

DO NOT USE

this appliance if any part has been under water. Immediately

CALL

qualified service technician to inspect the unit and to replace any part of the control

system and any gas control which has been underwater.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be

PERFORMED

by a qualified service person. The

appliance and venting system should be

INSPECTED

before initial use and at least

annually by a professional service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is

IMPERATIVE

that the

unit’s control compartment, burners, and circulating air passageways

BE KEPT

CLEAN

to provide for adequate combustion and ventilation air.

Always

KEEP

the appliance clear and free from combustible materials, gasoline, and

other flammable vapors and liquids.

NEVER OBSTRUCT

the flow of combustion and ventilation air. Keep the front of the

appliance

CLEAR

of all obstacles and materials for sevicing and proper operations.

Due to the high temperature, the appliance should be

LOCATED

out of traffic areas

and away from furniture and draperies. Clothing or flammable material

SHOULD NOT

BE PLACED

on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature

and should STAY AWAY to avoid burns or clothing ignition. Young children should be

CAREFULLY SUPERVISED when they are in the same room as the appliance.

These units

MUST

use one of the vent systems described in the Installing the Fireplace

section of the

Installers Guide

NO OTHER

vent systems or components

MAY BE USED

This gas fireplace and vent assembly

MUST

be vented directly to the outside and

MUST NEVER

be attached to a chimney serving a separate solid fuel burning

appliance. Each gas appliance

MUST USE

a separate vent system. Common vent

systems are

PROHIBITED

INSPECT

the external vent cap on a regular basis to make sure that no debris is

interfering with the air flow.

The glass door assembly

MUST

be in place and sealed, and the trim door assembly

MUST

be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE

this appliance with the glass door removed, cracked, or broken.

Replacement of the glass door should be performed by a licensed or qualified service

person.

DO NOT

strike or slam the glass door.

The glass door assembly

SHALL ONLY

be replaced as a complete unit, as supplied

by the gas fireplace manufacturer.

NO SUBSTITUTE

material may be used.

DO NOT USE

abrasive cleaners on the glass door assembly.

DO NOT ATTEMPT

clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a

qualified service technician perform an appliance check-up at the beginning

of each heating season.

Any safety screen or guard removed for servicing must be replaced before operating

this appliance.

Table of

Contents

i i

Safety and Warning Information ........................... i

Section 1: Approvals and Codes........................ .1

Approval Listings and Codes ..................................... 1

Appliance Certification ............................................... 1

Installation Codes ...................................................... 1

High Altitude Installations........................................... 1

Section 2: Getting Started .................................... 2

Introducing the Heat-N-Glo Direct Vent Gas Stoves..... 2

Pre-installation Preparation........................................ 2

Section 3: Installing the Stove ............................. 5

Step 1 Locating the Stove ...................................... 5

Step 2 Setting Up the Stove ................................... 6

Step 3 Installing the Vent System ........................... 7

A. Vent System Approvals........................... 7

B.InstallingVentComponents................... 14

C.VentTermination .................................... 19

Step 4 The Gas Control System .......................... 24

Step 5 The Gas Supply Line................................. 24

Step 6 Gas Pressure Requirements .................... 25

Step 7 Wiring the Stove........................................ 26

Step 8 Finishing .................................................... 27

Step 9 Installing Logs and Ember Material ........... 27

Positioning the Logs .................................. 27

Placing the Ember Material ....................... 27

Step 10 Before Lighting the Stove .......................... 28

Step 11 Lighting the Stove...................................... 28

After the Installation................................... 28

Section 4: Maintenance and Servicing.............. 29

Section 5: Replacement Parts

and Accessories ............................... 31

Replacement Parts .................................................. 31

Accessories .......................................................... 35

Approval Listings

and Codes Appliance Certification

The Heat-N-Glo gas stove models discussed in this

Installers Guide

have been tested to certification

standards and listed by the applicable laboratories.

CERTIFICATION

MODEL LABORATORY TYPE STANDARD

Townsend I & II Underwriters Vented Gas ANSI Z21.88• CSA2.33

Laboratories

Fireplace Heater

Installation Codes

Installationmustconformtolocal codes. In the absence of local codes installation

mustconformwiththecurrent National Fuel Gas CodeANSIZ223.1 (in the United

States) or with the current installation code CAN/CGA - B149 (in Canada).

The appliance when installed must be electrically grounded in accordance with

local codes; in absence of local codes, with the current National Electric Code

ANSI/ NFPA NO. 70 (in the United States) or with the current CSA C22.1 Cana-

dian Electric Code (in Canada).

High Altitude Installations

Theseunits are testedandapproved for elevations from0-2000feet. (In theUnited

States) and 0-4500 feet (in Canada).

When installing this unit at an elevation above 2000 feet, (in United States) it may

be necessary to decrease the input rating by changing the existing burner orifice

toasmallersize. Inputshouldbereduced4percentforeach1000 feet above sea

level. Check with your local gas company for help in determining the proper ori-

fice size.

When installing this unit at an elevation above 4500 feet (in Canada), check with

local authorities.

Consult your local gas company for assistance in determining the proper orifice

for location.

Approvals and

Regulations

Heat-N-Glo direct vent gas stoves are designed to

operate with all combustion air siphoned from outside

of the building and all exhaust gases expelled to the

outside.

The information contained in this

Installers Guide

unless noted otherwise, applies to all models and gas

control systems.

Gas stove diagrams, including the dimensions, are

shown in this section.

Pre-installation

Preparation This gas stove and its components are tested and

safe when installed in accordance with this

Installers

Guide

. Report to your dealer any parts damaged in

shipment, particularly the condition of the glass. Do

not install any unit with damaged, incomplete, or

substitute parts.

The vent system components and trim doors are

shipped in separate packages. The gas logs are

packaged separately and must be field installed.

Read all of the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benefit. Failure to follow these instructions

will void the owner’s warranty and may present a

fire hazard.

The Heat-N-Glo Warranty will be voided by, and Heat-

N-Glo disclaims any responsibility for, the following

actions:

• Installation of any damaged stove or vent system

component.

• Modification of the stove or vent system.

• Installation other than as instructed by Heat-N-Glo.

• Improper positioning of the gas logs or the glass

door.

• Installation and/or use of any component part not

manufactured and approved by Heat-N-Glo, not

withstanding any independent testing laboratory or

other party approval of such component part or

accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A

FIRE HAZARD.

Getting

Started

Introducing the

Heat-N-Glo

Direct Vent

Gas Stoves

Figure 1. Diagram of the TOWNSEND-I

When planning a stove installation, it’s necessary to determine:

•Where the unit is to be installed.

•The vent system configuration to be used.

•Gas supply piping.

•Electrical wiring.

•Framing and finishing details.

•Whether optional accessories—devices such as a fan, wall switch, or remote

control—are desired.

If the stove is to be installed on carpeting or tile, or on any combustible material

other than wood flooring, the stove should be installed on a metal or wood panel

that extends the full width and depth of the stove.

Figure 2. Diagram of the TOWNSEND-II

Installing

the Stove

Figure 3. Stove Dimensions, Locations, and Space Requirements

TOWNSEND I

TOWNSEND II

The diagram below shows space and clearance

requirements for locating the stove within a room.

Step 1

Locating the

Stove

Step 2

Setting up the

Stove

Removal of the cast front surround:

1. Remove the two small bolts from underneath the

front of the cast bottom. These bolts can be

discarded.

2. Remove the screw from underneath the front of

the grille.

3. The cast front surround can now be removed by

tilting its top towards the front and lifting it out of

the stove.

4. When the cast front surround is replaced, it can

be held in place with just the one screw in the

top, underneath the grille.

Removal of glass:

1. Remove the Cast Front Surround.

2. For TOWNSEND-I: Remove the six screws

securing the glass and remove the glass.

3. For TOWNSEND-II: Remove the four screws

located at the top, tilt the glass slightly toward

you and pull up and away from the unit.

To replace the glass reverse these steps.

Minimum Clearances from the Vent Pipe to Combustible Materials

For Vertical

For Horizontal Sections Sections At Wall Firestops

Top Bottom Sides Top Bottom Sides

3 inches 1 inch 1 inch 1 inch 2 1/2 inches 1/2 inch 1 inch

(75mm) (25mm) (25mm) (25mm) (63.7mm) (13mm) (25mm)

Minimum Clearances from the Fireplace to Combustible Materials

Glass Sides of Top of

Front Floor Rear Fireplace Fireplace

36 inches 0 4 inches 6 inches 55 inches

(914mm) (100mm) (150mm) (134cm)

The minimum clearance to a perpendicular wall

extending past the face of the fireplace is 6 inches

(150mm).

The back of the fireplace may NOT be recessed

into combustible construction.

Clearance Requirements

For minimum clearances, see the direct vent

termination clearance diagrams on pages 21 and 23

in this manual.

Step 3

Installing the

Vent System

A. Vent System Approvals

This model is approved for 4”/6 5/8” SL D-Series

vent pipe components and terminations. Approved

vent systems components are are labeled for

identification. NO OTHER VENT SYSTEMS OR

COMPONENTS MAY BE USED. Detailed installation

instructions are inclued with each vent termination

kit and should be used in conjuction with this manual.

WARNING:

A minimum 3 foot length of straight vent

pipe MUST be attached to the unit’s

starting collars for all vent systems.

Identifying Vent Components

The vent systems installed on this gas stove may

include one, two, or three 90°elbow assemblies.

The relationships of vertical rise to horizontal run in

vent configurations using 90° elbows MUST BE

strictly adhered to. The rise to run relationships are

shown in the vent drawings and tables. Refer to the

diagrams on the next several pages.

Figure 4. Vent Components and Terminations

Vent System Termination Kits

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo COSMO-I30AU Bedienungsanleitung

Heat & Glo

Heat & Glo 8000TV-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo Tiara Petite Montageanleitung

Heat & Glo

Heat & Glo Crescent II Bedienungsanleitung

Heat & Glo

Heat & Glo TRUE-36C Bedienungsanleitung

Heat & Glo

Heat & Glo NORTHSTAR-BK Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550BE-B Bedienungsanleitung

Heat & Glo

Heat & Glo NORTHSTAR-BK Bedienungsanleitung

Heat & Glo

Heat & Glo RED40-N-AU Bedienungsanleitung

Heat & Glo

Heat & Glo SOHO-N-CEB Programmierhandbuch

Heat & Glo

Heat & Glo SOHO24B Bedienungsanleitung

Heat & Glo

Heat & Glo SOHO24B Bedienungsanleitung

Heat & Glo

Heat & Glo 6000GBV-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550BE Bedienungsanleitung

Heat & Glo

Heat & Glo SLR-C (COSMO) Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550METRO-LP Bedienungsanleitung

Heat & Glo

Heat & Glo SL-3X Bedienungsanleitung

Heat & Glo

Heat & Glo SL350TRSI-N-CE Bedienungsanleitung

Heat & Glo

Heat & Glo FB-GRAND-S Bedienungsanleitung

Heat & Glo

Heat & Glo ST-HVBI-AUB Bedienungsanleitung

Heat & Glo

Heat & Glo ST-42TVFL-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CL-IFT-S Bedienungsanleitung

Heat & Glo

Heat & Glo 6000C-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo SLR32 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch