HeimVision HM243 Bedienungsanleitung
Network Video Recorder
System
HM243
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch
2
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆+44 (0)203 514 4411
Importer
Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz
3
SAFETY CAUTIONS
•Please keep the NVR away from liquid in case of short-circuit.
•Please use the product in an open space and do not block the air vents.
•For your safety, please use the original power supply provided.
•If the NVR starts or works abnormally, please unplug the power adapter and clean
the dust on the mainboard in the NVR device, then restart the NVR.
•Please obey the regulations and policies in your country and area when installing
the product.
ABBREVIATIONS OF TERMS
NVR: Network Video Recorder
HDD: Hard Disk Drive
SATA: Serial ATA, a common hardware interface employed by our NVR.
EseeCloud: A software designed for this product.
FAT32: A file system of your USB Drive.
4
PACKAGE LIST
NVR x1 IP Camera x4 5dB Antenna x4
(Hard Disk Drive (for IP Camera)
not included)
Ethernet Cable x1 DC 12V/2A DC 12V/1A
Power Adapter x1 Power Adapter x4
(for NVR) (for IP Camera)
USB Mouse x1 Screw x4 Screw package x4
(for HDD) (for IP cameras)
Quick Guide x1
5
PRODUCT OVERVIEW
Antenna
HD Output
Ethernet Port
USB Port
DC-In
LED
Installation Hole
Stand
Night Vision Sensor Antenna Ethernet Port DC-In
6
HARD DISK DRIVE INSTALLATION AND SYSTEM
CONNECTIONS
Hard Disk Drive Installation
Notice:
•To record video and play the recorded video, the installation of the Hard Disk Drive
is a must. Otherwise, you can only watch the live picture.
•A Hard Disk Drive is not included in this NVR System.
•This NVR system works with a 3.5” SATA HDD. The HDD should be formatted if it’s
installed.
Step 1:
Loosen the screws on the back of
the NVR and then remove the
cover.
Step 2:
Connect the power cables and
data cables to the corresponding
ports of your HDD.
Step 3:
Fasten the cover and HDD with
the four screws.
Step 4:
Fasten the cover on the back of
the NVR with the two screws.
7
System Connections
Do not fix the IP Camera with the screws before you can see the image on the
screen and know the ideal position to install it.
1. Unwind the antennas of the NVR;
2. Install and tighten the antennas on the IP cameras;
3. Plug the power adapter (12V/2A) into the NVR and the socket;
4. Plug the power adapter (12V/2A) into the IP Camera and the socket;
8
OPERATE NVR SYSTEM
Live Picture
Plug the NVR and cameras in and wait for 2-3 minutes. The live pictures from the
cameras will be displayed on the screen. Then you can connect the mouse to the NVR
and start operating the NVR system.
Notes:
•The default Username for the NVR system is admin, and the default Password is
empty (no need to enter anything);
•This NVR system can be only connected to the network by Ethernet cable currently;
•To protect your privacy, please set the password at your earliest convenience. Right
click the mouse on the main interface, then go to System setup > System Admin >
User > Set password to set a password;
Hard Disk Drive Formatting
Install the HDD first, then right click the mouse on the main interface and go to System
Setup > General Setup > HDD Setup to check its status. If it’s not Formatted, select the
right HDD, then click Format.
9
Video Recording
Right click the mouse on the main interface, then select System Setup > Record Setup >
Record Plan to set the record mode. The default record mode of the NVR is 24/7 all time
record.
Notice: Click Reset before you change the record mode.
Scheduled Record
After reset, select Channel and click Time to start scheduled record setup. Left click
the mouse and then select the day and hour you plan for recording. The area selected
will turn Red and click Apply to save the setting. The system will start recording at a
specific time on a daily/weekly schedule.
Motion Record
After reset, select Channel and click Motion to start motion record setup. Left click
the mouse and then select the day and hour you plan for recording. The area selected
will turn to Green and click Apply to save the setting. The system will start recording
when the camera detects any motion.
Tips:
•Changing the setting from 24/7 recording to motion recording helps to prolong your
HDD storage time.
•External device is required for Alarm record and this NVR does not support it.
10
Video Playback
Right click the mouse on the main interface, then select Video Playback to play the
recorded videos. Select the date with green color, Channel and Record Mode (⑥), then
click Search to list all the filtered videos.
1. Display the timeline by Day/Hour 4. Pause/Play/Fast Forward
2. Video Recording Time 5. Filtered Videos List
3. Area for Video Playing 6. Filters
Option 1: Select one video file from the Filtered Videos List (⑤), then click Play or File
Playback to play the selected video.
Option 2: Left click the mouse on the Red/Green (Red for Scheduled Record and Green
for Motion Record) part of the timeline. The videos recorded from 4 channels can be
played at the same time.
Video Backup
Option 1:
Insert a USB drive (up to 64GB and FAT32 format only), then select Video Playback to
enter the interface below.
Option 2:
Right click the mouse on the main interface then select Video Playback to enter the
interface below.
Inhaltsverzeichnis
Sprachen:
Andere HeimVision Netzwerk-Hardware Handbücher
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
